Add support to show CPSW hardware statistics to user via ethtool
so user can find if there were any error reported by hardware or
the system is over loaded duing high data rate transfer.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The error is found by the checkpatch.pl tools.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need rtnl protection while reading slave_cnt and updating
the .fail_over_mac, and it also follows the logic "don't change
anything slave-related without rtnl". :)
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net/bonding/bond_sysfs.c:1302: ERROR: else should follow close brace '}'
net/bonding/bond_sysfs.c:1314: ERROR: else should follow close brace '}'
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The slave_xxx_netpoll will call synchronize_rcu_bh(),
so the function may schedule and sleep, it should't be
called under spinlocks.

bond_netpoll_setup() and bond_netpoll_cleanup() are always
protected by rtnl lock, it is no need to take the read lock,
as the slave list couldn't be changed outside rtnl lock.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves all enic ethtool hooks from enic_main.c to a new file
enic_ethtool.c
Signed-off-by: NNeel Patel <neepatel@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NNishank Trivedi <nistrive@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch gets rid of the following warning:

net/9p/trans_rdma.c:594:12: warning: ‘rdma_cancelled’ defined but not used [-Wunused-function]
 static int rdma_cancelled(struct p9_client *client, struct p9_req_t *req)

The rdma_cancelled function is not called anywhere in the kernel
Signed-off-by: NAndi Shyti <andi@etezian.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sathya Perla says:

====================
The following patches are mostly for providing MAC
filtering ability for VFs. Pls apply. Thanks!
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the UC-list is being deleted from the HW MAC table, but the primary
MAC is not.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On SH-R and Lancer-R, GET_MAC_LIST cmd is better supported
(instead of NTWK_MAC_QUERY cmd) to query provisioned MAC addresses.
Similiarly, (on SH-R and Lancer-R) SET_MAC_LIST must be used by the PF to
provision a permanent MAC addresses to the VF.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code to configure the permanent MAC in be_setup() has become quite
complicated, with different FW cmds being used for BEx, SH-R and Lancer.
Simplify the logic by moving some of this complexity to be_cmds.c. This
makes the code in be_setup() a little more readable.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For BE3 VFs, the permanent MAC is added by its PF. The VF can retrieve its
pmac_id only via the IFACE_CREATE cmd. This is not true for Lancer and SH-R
VFs which get the pmac_id by issuing a ADD_IFACE_MAC cmd. So, use this
hack only for BE3 VFs.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the current design VFs were not allowed to program MAC/VLAN filters.
Only the PF driver was allowed to configure/provision MAC and transparent
VLANs to a VF. Change this to support MAC/VLAN filtering on a VF by a VM.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the VFs by default don't have the privilege to modify MAC address.
This will change in a subsequent fix wherein VFs will have the ability to
modify MAC/VLAN filters.

Fix be_mac_addr_set() logic to support MAC address modification on a
privileged VF too.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a copy of support for r8a7778/9 with the .rmiimode mode bit
of struct sh_eth_cpu_data set.

Also update R8A7779 to R8A777x.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This register is prsent on the r8a7790 SoC.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "int addrlen" in fib6_add_1 is rebundant, as we can get it from
parameter "struct in6_addr *addr" once we modified its type.
And also fix some coding style issues in fib6_add_1
Signed-off-by: NFan Du <fan.du@windriver.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Seting rt->rt6i_nsiblings to zero is rebundant, because above memset
zeroed the rest of rt excluding the first dst memember.
Signed-off-by: NFan Du <fan.du@windriver.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GRE tunnel and IPIP tunnel already switched to the new
ip tunnel code, VTI tunnel can use it too.

Cc: Pravin B Shelar <pshelar@nicira.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Saurabh Mohan <saurabh.mohan@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the prototpye of the ip6_mr_forward() method to return void
instead of int.

The ip6_mr_forward() method always returns 0; moreover, the return value of this
method is not checked anywhere.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the prototpye of the ip_mr_forward() method to return void
instead of int.

The ip_mr_forward() method always returns 0; moreover, the return value of this
method is not checked anywhere.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
The middle patch adjusts core infrastructure so the bonding code can be
generalized and reused by team.

v1->v2: using msecs_to_jiffies() as suggested by Eric

Jiri Pirko (3):
  team: add peer notification
  net: convert resend IGMP to notifier event
  team: add support for sending multicast rejoins
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to what is implemented in bonding. User is able to ask team
driver to send IGMP rejoins in case port is enabled or disabled. Using
previously introduced netdev notifier.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until now, bond_resend_igmp_join_requests() looks for vlans attached to
bonding device, bridge where bonding act as port manually. It does not
care of other scenarios, like stacked bonds or team device above. Make
this more generic and use netdev notifier to propagate the event to
upper devices and to actually call ip_mc_rejoin_groups().
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When port is enabled or disabled, allow to notify peers by unsolicitated
NAs or gratuitous ARPs. Disabled by default.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for iproute2 command 'bridge fdb replace ...'.
The rtnletlink call back function ndo_fdb_add will be called
with the NLM_F_REPLACE flag set.
Simply return -EOPNOTSUP.

Resubmitted because net-next was closed last week.
Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to replace an existing entry found in the
vxlan fdb database. The entry in question is identified
by its unicast mac address and the destination information
is changed. If the entry is not found, it is added in the
forwarding database. This is similar to changing an entry
in the neighbour table.

Multicast mac addresses can not be changed with the replace
option.

This is useful for virtual machine migration when the
destination of a target virtual machine changes. The replace
feature can be used instead of delete followed by add.

Resubmitted because net-next was closed last week.
Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yuchung Cheng says:

====================
This patch series improve RTT sampling in three ways:
1. Sample RTT during fast recovery and reordering events.
2. Favor ack-based RTT to timestamps because of broken TS ECR fields
3. Consolidate the RTT measurement logic.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If RTT is not available because Karn's check has failed or no
new packet is acked, use the RTT measured from SACK to estimate
the RTO. The sender can continue to estimate the RTO during loss
recovery or reordering event upon receiving non-partial ACKs.

This also changes when the RTO is re-armed. Previously it is
only re-armed when some data is cummulatively acknowledged (i.e.,
SND.UNA advances), but now it is re-armed whenever RTT estimator
is updated. This feature is particularly useful to reduce spurious
timeout for buffer bloat including cellular carriers [1], and
RTT estimation on reordering events.

[1] "An In-depth Study of LTE: Effect of Network Protocol and
 Application Behavior on Performance", In Proc. of SIGCOMM 2013
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Take RTT sample if an ACK selectively acks some sequences that
have never been retransmitted. The Karn's algorithm does not apply
even if that ACK (s)acks other retransmitted sequences, because it
must been generated by an original but perhaps out-of-order packet.
There is no ambiguity. In case when multiple blocks are newly
sacked because of ACK losses the earliest block is used to
measure RTT, similar to cummulative ACKs.

Such RTT samples allow the sender to estimate the RTO during loss
recovery and packet reordering events. It is still useful even with
TCP timestamps. That's because during these events the SND.UNA may
not advance preventing RTT samples from TS ECR (thus the FLAG_ACKED
check before calling tcp_ack_update_rtt()).  Therefore this new
RTT source is complementary to existing ACK and TS RTT mechanisms.

This patch does not update the RTO. It is done in the next patch.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefer packet timings to TS-ecr for RTT measurements when both
sources are available. That's because broken middle-boxes and remote
peer can return packets with corrupted TS ECR fields. Similarly most
congestion controls that require RTT signals favor timing-based
sources as well. Also check for bad TS ECR values to avoid RTT
blow-ups. It has happened on production Web servers.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first patch consolidates SYNACK and other RTT measurement to use a
central function tcp_ack_update_rtt(). A (small) bonus is now SYNACK
RTT measurement happens after PAWS check, potentially reducing the
impact of RTO seeding on bad TCP timestamps values.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fabio Estevam says:

====================
This series improves clock handling in the driver by not enabling/disabling
the optional ptp and enet_out clocks unconditionally, check for the return value
of clk_prepare_enable and also handle clk_ptp in suspend/resume.

Remove an unneeded check in platform_get_resource() and also use
devm_request_irq() that can help to simplify the code.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NFrank Li <lznuaa@gmail.com>

Using devm_request_irq() can make the code smaller and cleaner.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As devm_ioremap_resource() is used, there is no need to explicitely check the
return value from platform_get_resource(), as this is something that
devm_ioremap_resource() takes care by itself.

Also, place platform_get_resource() prior to devm_ioremap_resource() for
better code readability.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

clk_ptp should also be enabled in fec_resume() and disabled in fec_suspend().
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On fec_probe the clocks are enabled in the following order:

clk_ahb -> clk_ipg -> clk_enet_out -> clk_ptp

, so in the error and remove paths we should disabled them in the opposite
order.

Also fix the order in the suspend/resume functions.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

clk_enet_out and clk_ptp are optional clocks, so we should not enable/disable
them unconditionally.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds transmit time stamping to the tun/tap driver. Similar
support already exists for UDP, can, and raw packets.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>