- 21 5月, 2021 1 次提交
-
-
由 Yufeng Mo 提交于
Currently, the debugfs command for reg is implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, create some files "bios_common/ssu/igu_egu/rpu/ncsi/rtc/ppp/rcb/tqp/mac" for it, and query it by command "cat xxx", return the result to userspace, rather than record in dmesg. The display style is below: $ cat bios_common BP_CPU_STATE: 0x0 DFX_MSIX_INFO_NIC_0: 0xc000 DFX_MSIX_INFO_NIC_1: 0x0 DFX_MSIX_INFO_NIC_2: 0x0 DFX_MSIX_INFO_NIC_3: 0x0 DFX_MSIX_INFO_ROC_0: 0xc000 DFX_MSIX_INFO_ROC_1: 0x0 DFX_MSIX_INFO_ROC_2: 0x0 DFX_MSIX_INFO_ROC_3: 0x0 Signed-off-by: NYufeng Mo <moyufeng@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 18 5月, 2021 1 次提交
-
-
由 Yang Shen 提交于
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:121: warning: expecting prototype for hns_mac_is_adjust_link(). Prototype was for hns_mac_need_adjust_link() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:386: warning: expecting prototype for hns_mac_queue_config_bc_en(). Prototype was for hns_mac_port_config_bc_en() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:607: warning: expecting prototype for hns_mac_set_autoneg(). Prototype was for hns_mac_set_pauseparam() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:236: warning: expecting prototype for hns_ppe_qid_cfg(). Prototype was for hns_dsaf_ppe_qid_cfg() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:623: warning: expecting prototype for dsaf_tbl_tcam_mcast_cfg(). Prototype was for hns_dsaf_tbl_tcam_mcast_cfg() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:1220: warning: expecting prototype for hns_dsaf_tbl_tcam_init(). Prototype was for hns_dsaf_comm_init() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:2121: warning: expecting prototype for dsaf_pfc_unit_cnt(). Prototype was for hns_dsaf_pfc_unit_cnt() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:2153: warning: expecting prototype for dsaf_port_work_rate_cfg(). Prototype was for hns_dsaf_port_work_rate_cfg() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:2745: warning: expecting prototype for hns_dsaf_get_sset_count(). Prototype was for hns_dsaf_get_regs_count() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:2957: warning: expecting prototype for dsaf_probe(). Prototype was for hns_dsaf_probe() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:3011: warning: expecting prototype for dsaf_remove(). Prototype was for hns_dsaf_remove() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c:366: warning: expecting prototype for hns_dsaf_srst_chns(). Prototype was for hns_dsaf_srst_chns_acpi() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c:509: warning: expecting prototype for hns_mac_get_sds_mode(). Prototype was for hns_mac_get_phy_if() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_ppe.c:303: warning: expecting prototype for ppe_init_hw(). Prototype was for hns_ppe_init_hw() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_ppe.c:350: warning: expecting prototype for ppe_uninit_hw(). Prototype was for hns_ppe_uninit_hw() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_ppe.c:391: warning: expecting prototype for hns_ppe_reset(). Prototype was for hns_ppe_reset_common() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_ppe.c:464: warning: expecting prototype for ppe_get_strings(). Prototype was for hns_ppe_get_strings() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_rcb.c:920: warning: expecting prototype for rcb_get_sset_count(). Prototype was for hns_rcb_get_ring_regs_count() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_xgmac.c:112: warning: expecting prototype for hns_xgmac_tx_lf_rf_insert(). Prototype was for hns_xgmac_lf_rf_insert() instead drivers/net/ethernet/hisilicon/hns/hns_dsaf_xgmac.c:122: warning: expecting prototype for hns_xgmac__lf_rf_control_init(). Prototype was for hns_xgmac_lf_rf_control_init() instead drivers/net/ethernet/hisilicon/hns/hns_enet.c:777: warning: expecting prototype for hns_nic_adp_coalesce(). Prototype was for hns_nic_adpt_coalesce() instead drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:202: warning: expecting prototype for hns_nic_set_link_settings(). Prototype was for hns_nic_set_link_ksettings() instead drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:837: warning: expecting prototype for get_ethtool_stats(). Prototype was for hns_get_ethtool_stats() instead drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:894: warning: expecting prototype for get_strings(). Prototype was for hns_get_strings() instead Cc: Yisen Zhuang <yisen.zhuang@huawei.com> Cc: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: NYang Shen <shenyang39@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 15 5月, 2021 16 次提交
-
-
由 Peng Li 提交于
Void function return statements are not generally useful, so remove the redundant return. Signed-off-by: NPeng Li <lipeng321@huawei.com> Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peng Li 提交于
Add the space required before the open brace '{'. Signed-off-by: NPeng Li <lipeng321@huawei.com> Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peng Li 提交于
Spaces at the start of a line will cause checkpatch warning. This patch replaces the spaces by tab at the start of a line. Signed-off-by: NPeng Li <lipeng321@huawei.com> Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peng Li 提交于
Networking block comments don't use an empty /* line, use /* Comment... This patch fix the comments style issue. Signed-off-by: NPeng Li <lipeng321@huawei.com> Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiaran Zhang 提交于
Currently, the debugfs command for ncl config is implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, create a single file "ncl_config" for it, and query it by command "cat ncl_config", return the result to userspace, rather than record in dmesg. The display style is below: $cat ncl_config offset | data 0x0000 | 0x00000028 0x0004 | 0x00000400 0x0008 | 0x08040201 0x000c | 0x00000000 0x0010 | 0x00040004 0x0014 | 0x00040004 0x0018 | 0x00000000 0x001c | 0x00000000 0x0020 | 0x00040004 Signed-off-by:
Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiaran Zhang 提交于
Currently, the debugfs command for m7 info is implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, create a single file "imp_info" for it, and query it by command "cat imp_info", return the result to userspace, rather than record in dmesg. The display style is below: $cat imp_info offset | data 0x0000 | 0x00000000 0x00000000 0x0008 | 0x00000000 0x00000000 0x0010 | 0x00000000 0x00000001 0x0018 | 0x00000000 0x00000000 0x0020 | 0x00000000 0x00000000 0x0028 | 0x00000000 0x00000000 0x0030 | 0x00000000 0x00000000 Signed-off-by:
Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiaran Zhang 提交于
Currently, the debugfs command for reset info is implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, create a single file "reset_info" for it, and query it by command "cat reset_info", return the result to userspace, rather than record in dmesg. The display style is below: $cat reset_info PF reset count: 0 FLR reset count: 0 GLOBAL reset count: 0 IMP reset count: 0 reset done count: 0 HW reset done count: 0 reset count: 0 reset fail count: 0 vector0 interrupt enable status: 0x1 reset interrupt source: 0x0 reset interrupt status: 0x0 RAS interrupt status:0x0 hardware reset status: 0x0 handshake status: 0x80 function reset status: 0x0 Change to the "hclge_show_rst_info" in the "hclge_reset_err_handle", when the reset fails, display reset info immediately. Signed-off-by:
Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiaran Zhang 提交于
Currently, the debugfs command for intr is implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, create a single file "interrupt_info" for it, and query it by command "cat interrupt_info", return the result to userspace, rather than record in dmesg. The display style is below: $cat interrupt_info num_nic_msi: 65 num_roce_msi: 65 num_msi_used: 2 num_msi_left: 128 Signed-off-by:
Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yufeng Mo 提交于
Currently, the debugfs command for loopback is implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, create a single file "loopback" for it, and query it by command "cat loopback", return the result to userspace, rather than record in dmesg. The display style is below: $ cat loopback mac id: 0 app loopback: off serdes serial loopback: off serdes parallel loopback: off Signed-off-by: NYufeng Mo <moyufeng@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yufeng Mo 提交于
Currently, the debugfs command for mng tbl is implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, create a single file "mng_tbl" for it, and query it by command "cat mng_tbl", return the result to userspace, rather than record in dmesg. The display style is below: $ cat mng_tbl entry mac_addr mask ether mask vlan mask i_map ... 00 00:00:00:00:00:00 0 88cc 0 0000 1 0f ... Signed-off-by: NYufeng Mo <moyufeng@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Huazhong Tan 提交于
Currently, the debugfs command for mac list info is implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, create two files "uc" and "mc" under directory "mac_list" for it, and query mac list info by "cat mac_list/uc" and "mac_list/mc", return the result to userspace, rather than record in dmesg. The display style is below: $ cat mac_list/uc UC MAC_LIST: FUNC_ID MAC_ADDR STATE pf 00:18:2d:00:00:71 ACTIVE $ cat mac_list/mc MC MAC_LIST: FUNC_ID MAC_ADDR STATE pf 01:80:c2:00:00:21 ACTIVE Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Huazhong Tan 提交于
Currently, the debugfs command for bd info is implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, add two debugfs directories "tx_bd_info" and "rx_bd_info", and create a file for each queue under these two directories, and query the bd info of specific queue by "cat tx_bd_info/tx_bd_queue*" or "cat rx_bd_info/rx_bd_queue*", return the result to userspace, rather than record in dmesg. The display style is below: $ cat rx_bd_info/rx_bd_queue0 Queue 0 rx bd info: BD_IDX L234_INFO PKT_LEN SIZE... 0 0x0 60 60... 1 0x0 1512 1512... $ cat tx_bd_info/tx_bd_queue0 Queue 0 tx bd info: BD_IDX ADDRESS VLAN_TAG SIZE... 0 0x0 0 0... 1 0x0 0 0... Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiaran Zhang 提交于
Currently, the debugfs command for dev capability and dev spec are implemented by "echo xxxx > cmd", and record the information in dmesg. It's unnecessary and heavy. To improve it, create a single file "dev_info" for them, and query them by command "cat dev_info", return the result to userspace, rather than record in dmesg. The display style is below: $cat dev_info dev capability: support FD: yes support GRO: yes support FEC: yes support UDP GSO: no support PTP: no support INT QL: no support HW TX csum: no support UDP tunnel csum: no support TX push: no support imp-controlled PHY: no support rxd advanced layout: no dev spec: MAC entry num: 0 MNG entry num: 0 MAX non tso bd num: 8 RSS ind tbl size: 512 RSS key size: 40 RSS size: 1 Allocated RSS size: 0 Task queue pairs numbers: 1 RX buffer length: 2048 Desc num per TX queue: 1024 Desc num per RX queue: 1024 Total number of enabled TCs: 1 MAX INT QL: 0 MAX INT GL: 8160 MAX TM RATE: 100000 MAX QSET number: 1024 Signed-off-by:
Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yufeng Mo 提交于
Currently, each debugfs command needs to create a file to get the information. To better support more debugfs commands, the debugfs process is reconstructed, including the process of creating dentries and files, and obtaining information. Signed-off-by: NYufeng Mo <moyufeng@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Huazhong Tan 提交于
Only when RXD advanced layout is enabled, in some cases (e.g. ip fragments), the checksum of entire packet will be calculated and filled in the least significant 16 bits of the unused addr field. So refactor out the handling of RX completion checksum: adjust the location of the checksum in RX descriptor, and use ptype table to identify whether this kind of checksum is calculated. Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Huazhong Tan 提交于
Currently, the driver gets packet type by parsing the L3_ID/L4_ID/OL3_ID/OL4_ID from RX descriptor, it's time-consuming. Now some new devices support RXD advanced layout, which combines previous OL3_ID/OL4_ID to 8bit ptype field, so the driver gets packet type by looking up only one table, and L3_ID/L4_ID become reserved fields. Considering compatibility, the firmware will report capability of RXD advanced layout, the driver will identify and enable it by default. This patch provides basic function: identify and enable the RXD advanced layout, and refactor out hns3_rx_checksum() by using ptype table to handle RX checksum if supported. Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 5月, 2021 4 次提交
-
-
由 Yufeng Mo 提交于
If selftest and reset are performed at the same time, the phy loopback setting may be still in enable state after the reset, and device cannot link up. So fix this issue by disabling phy loopback before phy_start(). Fixes: 256727da ("net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC") Signed-off-by: NYufeng Mo <moyufeng@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yufeng Mo 提交于
HW error and global reset are reported through MSIX interrupts. The same error may be reported to different functions at the same time. When global reset begins, the pending reset request set by this error is unnecessary. So clear the pending reset request after the reset is complete to avoid the repeated reset. Fixes: f6162d44 ("net: hns3: add handling of hw errors reported through MSIX") Signed-off-by: NYufeng Mo <moyufeng@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peng Li 提交于
Currently, netif_tx_stop_all_queues() is used to ensure that the xmit is not running, but for the concurrent case it will not take effect, since netif_tx_stop_all_queues() just sets a flag without locking to indicate that the xmit queue(s) should not be run. So use netif_tx_disable() to replace netif_tx_stop_all_queues(), it takes the xmit queue lock while marking the queue stopped. Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: NPeng Li <lipeng321@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hao Chen 提交于
When skb->ip_summed is CHECKSUM_PARTIAL, for non-tunnel udp packet, which has a dest port as the IANA assigned, the hardware is expected to do the checksum offload, but the hardware whose version is below V3 will not do the checksum offload when udp dest port is 4790. So fixes it by doing the checksum in software for this case. Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: NHao Chen <chenhao288@hisilicon.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 4月, 2021 3 次提交
-
-
由 Jian Shen 提交于
In some cases, the device is not initialized because reset failed. If another task calls hns3_reset_notify_up_enet() before reset retry, it will cause an error since uninitialized pointer access. So add check for HNS3_NIC_STATE_INITED before calling hns3_nic_net_open() in hns3_reset_notify_up_enet(). Fixes: bb6b94a8 ("net: hns3: Add reset interface implementation in client") Signed-off-by: NJian Shen <shenjian15@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yufeng Mo 提交于
The message sent to VF should be initialized, otherwise random value of some contents may cause improper processing by the target. So add a initialization to message in hclge_get_link_mode(). Fixes: 9194d18b ("net: hns3: fix the problem that the supported port is empty") Signed-off-by: NYufeng Mo <moyufeng@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yufeng Mo 提交于
According to the UM, the type and enable status of igu_egu_hw_err should be configured separately. Currently, the type field is incorrect when disable this error. So fix it by configuring these two fields separately. Fixes: bf1faf94 ("net: hns3: Add enable and process hw errors from IGU, EGU and NCSI") Signed-off-by: NYufeng Mo <moyufeng@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 20 4月, 2021 3 次提交
-
-
由 Huazhong Tan 提交于
The SEPARATOR_VALUE macro is used as separator when getting the register value, but the value of this macro is different between pf and vf, it is a bit confusing for the user, so synchronize the value of vf with pf. Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Huazhong Tan 提交于
Modify some inappropriate spaces in comments of struct hlcgevf_tqp_stats. Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Huazhong Tan 提交于
When enter suspend mode the counter of pf reset will be increased twice, since both hclge_prepare_general() and hclge_prepare_wait() increase this counter. So remove the duplicate counting in hclge_prepare_general(). Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 16 4月, 2021 2 次提交
-
-
由 Guangbin Huang 提交于
To reduce the processing of unnecessary mailbox command when PF supports actively push its link status to VFs, VFs stop sending request link status command in periodic service task in this case. Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Guangbin Huang 提交于
Previously, VF updates its link status every second by send query command to PF in periodic service task. If link stats of PF is changed, VF may need at most one second to update its link status. To reduce delay of link status between PF and VFs, PF actively push its link status to VFs when its link status is updated. And to let VF know PF supports this new feature, the link status changed mailbox command adds one bit to indicate it. Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 4月, 2021 1 次提交
-
-
由 Michael Walle 提交于
of_get_mac_address() returns a "const void*" pointer to a MAC address. Lately, support to fetch the MAC address by an NVMEM provider was added. But this will only work with platform devices. It will not work with PCI devices (e.g. of an integrated root complex) and esp. not with DSA ports. There is an of_* variant of the nvmem binding which works without devices. The returned data of a nvmem_cell_read() has to be freed after use. On the other hand the return of_get_mac_address() points to some static data without a lifetime. The trick for now, was to allocate a device resource managed buffer which is then returned. This will only work if we have an actual device. Change it, so that the caller of of_get_mac_address() has to supply a buffer where the MAC address is written to. Unfortunately, this will touch all drivers which use the of_get_mac_address(). Usually the code looks like: const char *addr; addr = of_get_mac_address(np); if (!IS_ERR(addr)) ether_addr_copy(ndev->dev_addr, addr); This can then be simply rewritten as: of_get_mac_address(np, ndev->dev_addr); Sometimes is_valid_ether_addr() is used to test the MAC address. of_get_mac_address() already makes sure, it just returns a valid MAC address. Thus we can just test its return code. But we have to be careful if there are still other sources for the MAC address before the of_get_mac_address(). In this case we have to keep the is_valid_ether_addr() call. The following coccinelle patch was used to convert common cases to the new style. Afterwards, I've manually gone over the drivers and fixed the return code variable: either used a new one or if one was already available use that. Mansour Moufid, thanks for that coccinelle patch! <spml> @a@ identifier x; expression y, z; @@ - x = of_get_mac_address(y); + x = of_get_mac_address(y, z); <... - ether_addr_copy(z, x); ...> @@ identifier a.x; @@ - if (<+... x ...+>) {} @@ identifier a.x; @@ if (<+... x ...+>) { ... } - else {} @@ identifier a.x; expression e; @@ - if (<+... x ...+>@e) - {} - else + if (!(e)) {...} @@ expression x, y, z; @@ - x = of_get_mac_address(y, z); + of_get_mac_address(y, z); ... when != x </spml> All drivers, except drivers/net/ethernet/aeroflex/greth.c, were compile-time tested. Suggested-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NMichael Walle <michael@walle.cc> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 4月, 2021 1 次提交
-
-
由 Colin Ian King 提交于
The reset_prepare and reset_done calls have a null pointer check on ae_dev however ae_dev is being dereferenced via the call to ns3_is_phys_func with the ae->pdev argument. Fix this by performing a null pointer check on ae_dev and hence short-circuiting the dereference to ae_dev on the call to ns3_is_phys_func. Addresses-Coverity: ("Dereference before null check") Fixes: 715c58e9 ("net: hns3: add suspend and resume pm_ops") Signed-off-by: NColin Ian King <colin.king@canonical.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 10 4月, 2021 1 次提交
-
-
由 Salil Mehta 提交于
Some trivial spelling mistakes which caught my eye during the review of the code. Signed-off-by: NSalil Mehta <salil.mehta@huawei.com> Link: https://lore.kernel.org/r/20210409074223.32480-1-salil.mehta@huawei.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>
-
- 09 4月, 2021 2 次提交
-
-
由 Jiaran Zhang 提交于
To implement the system suspend/resume functions, the NIC driver needs to support: 1. When the system enters the suspend mode, the driver needs to implement the suspend callback function of the NIC device. The driver needs to mute the device, stop all RX/TX activities of the device, and unmap the interrupt. 2. When the system enters the resume mode, the driver needs to implement the resume callback function of the NIC device and restore the device to the state before suspension. When the system enters the suspend and resume mode, the NIC driver actually executes the PF function reset process. When the PFs are suspending/resuming, VFs also enter the suspend/resume state because the PFs trigger the VFs to reset, therefore no operation is required when the VF pci_driver is suspending or resuming. Signed-off-by:
Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiaran Zhang 提交于
The flr_prepare/flr_done functions are not only used in the FLR scenario, but also used in the suspend/resume. Change the function names to prepare_for_reset/rebuild_for_reset, change the flr_prepare/flr_done to reset_prepare/reset_done in hnae3_ae_ops. Signed-off-by:
Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 07 4月, 2021 1 次提交
-
-
由 Guangbin Huang 提交于
Currently, the VF down state bit is cleared after VF sending link status request command. There is problem that when VF gets link status replied from PF, the down state bit may still set as 1. In this case, the link status replied from PF will be ignored and always set VF link status to down. To fix this problem, clear VF down state bit before VF requests link status. Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com> Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 06 4月, 2021 3 次提交
-
-
由 Salil Mehta 提交于
Limiting the scope of the variable vector_ring_chain to the block where it is used. Fixes: 424eb834 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC") Signed-off-by: NSalil Mehta <salil.mehta@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Salil Mehta 提交于
Code to defer the reset(which caps the frequency of the reset) schedules the timer and returns. Hence, following 'else-if' looks un-necessary. Fixes: 9de0b86f ("net: hns3: Prevent to request reset frequently") Signed-off-by: NSalil Mehta <salil.mehta@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Salil Mehta 提交于
This removes the left over check and assignment which is no longer used anywhere in the function and should have been removed as part of the below mentioned patch. Fixes: 012fcb52 ("net: hns3: activate reset timer when calling reset_event") Signed-off-by: NSalil Mehta <salil.mehta@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 02 4月, 2021 1 次提交
-
-
由 Lu Wei 提交于
Fix some typos. Reported-by: NHulk Robot <hulkci@huawei.com> Signed-off-by: NLu Wei <luwei32@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-