The nwifi header is padded to 4 bytes. This wasn't
a problem until one tried to (at least) rx 4addr
frames.

This finally allows managed iface to be used in a
bridge.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Makes it easier to determine why some failures
happened.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Implement the get TSF by simply returning 0 so that IBSS
merging is happening. Otherwise, IBSS nodes that have similar
SSID naming won't merge. This is simply fooling the mac80211
that the TSF in the received beacon is higher than the local TSF.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This allows dynamic changes of bandwidth/nss/smps,
e.g. via ht/vht operation mode change
notification.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware ignores SMPS flags in peer assoc command.

For SMPS to work it is necessary to set peer
parameter after peer assoc command so that tx
chainmask is setup properly.

This should fix packet loss and improve throughput
with stations that have SMPS enabled upon
association.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

I modified Michal's commit c930f744 ("ath10k: implement channel switching") to return
when vdev_start() fails, but forgot to release conf_mutex.

Found by coccinelle:

>> drivers/net/wireless/ath/ath10k/mac.c:2745:5-11: preceding lock on line 2663
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes a checkpatch warning in ath10k:

drivers/net/wireless/ath/ath10k/mac.c:1636: WARNING: Avoid CamelCase: <regpair->regDmnEnum>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix a checkpatch warning:

drivers/net/wireless/ath/ath10k/debug.h:95: CHECK: Alignment should match open parenthesis
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

As result deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In case IRQ configuration is unknown possibly enabled MSIs
are left enabled in ath10k_pci_deinit_irq(). This update
fixes the described misbehaviour.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The documentation states that pci_enable_msi_block() returns the number of
requests 'could have been allocated', not 'could allocate'. IOW, MSIs are *not*
enabled if a positive value returned.

kvalo: add commit log based on Alexander's email
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Pass frames with invalid peer status to upper layer.
Next mac80211 will validate frames and drop if required.
This is required to detect spurious frames and pass
this info to user mode (detect CLASS2 CLASS3 frames from
nonauthenticated/nonassociated stations).
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is a workaround for HT-enabled STAs which break the spec
and have no HT capabilities RX mask (no HT RX MCS map).

As per spec, in section 20.3.5 Modulation and coding scheme (MCS),
MCS 0 through 7 are mandatory in 20MHz with 800 ns GI at all STAs.

Firmware asserts if such situation occurs.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In case of warm reset target need to be suspended.
Suspend function is extented to handle both cases
with disabling interrupts and without disabling interrupts.
Warm target reset requires suspend with all interrupts
disabled.

This patch depends on
ath10k: fix device initialization routine
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Suspend/resume callbacks are not protected by configuration mutex
so adding such protection. Also in order to simplify implemetation
of suspend function wait queue is replaced by completion.
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Hardware CUS232 version 2 has some issues with cold
reset that lead to Data Bus Errors or system hangs
in some cases. It's safer to use warm reset when
possible as it shouldn't trigger the
aforementioned issues.

Prefer warm reset over cold reset. However since
warm reset doesn't work after FW crash make sure to
fallback to cold reset when booting up the HW.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was found during testing the nss calculation does not
cover all corner cases. Station could request eq. only MCS8
and MCS9 (nss=2 specific). Next num_rates=2 so the driver
sets nss=(max((2+7)/8, 1))=1. Which is wrong. The in-driver
calculation was introduced prior (commit ddcc347b
mac80211: fix rx_nss calculation for drivers with hw rc).
Since it's fixed, use mac80211 provided value from now.
End user will experience lower throuhputs than expected
if the nss is wrongly calculated.
Signed-off-by: NMarek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This throw a lot of pointless warnings in case of DFS (radar
detection) and PHYERR events from firmware, when firmware may
actually insert more data, than we assume.

Besides of being noisy this debug does not protect or check
anything usefull currently. It was introduced long time ago
while debugging aggregations. So just removing it.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Make it easier to grep for htt rx errors.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Show message length and expected length.  Helps debug
firmware mismatch issues.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ieee80211_rx_status.flags is full. Define a new vht_flag
variable to be able to set more VHT related flags and make
room in flags.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath10k]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Aids in understanding excactly what a firmware is
offering.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ARP frames exchange does not work properly for UAPSD enabled AP.
ARP requests which arrives with access category 0 are processed
by network stack and send back with access category 0. FW changes
access category to 6. This is causing problems when UAPSD associated
STA is sleeping after has sent ARP request. Configure ARP access
category in FW to best effort (0) solves this problem. ARP frames
will be send with access category 0.

Simplify arp ac override functionality by removing redundant entry in
pdev param maping table. There should be only one entry in pdev param
map but enum has different name for different FW.

kvalo: change the warning message
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If recovery failed ath10k returned 0 (success) and
mac80211 continued to call other driver callbacks.
This caused null dereference.

This is how the failure looked like:

ath10k: ctl_resp never came in (-110)
ath10k: failed to connect to HTC: -110
ath10k: could not init core (-110)
BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffffa0b355c1>] ath10k_ce_send+0x1d/0x15d [ath10k_pci]
PGD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: ath10k_pci ath10k_core ath5k ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nf_nat_ipv4 ]
CPU: 1 PID: 36 Comm: kworker/1:1 Tainted: G        WC   3.13.0-rc8-wl-ath+ #8
Hardware name: To be filled by O.E.M. To be filled by O.E.M./HURONRIVER, BIOS 4.6.5 05/02/2012
Workqueue: events ieee80211_restart_work [mac80211]
task: ffff880215b521c0 ti: ffff880215e18000 task.ti: ffff880215e18000
RIP: 0010:[<ffffffffa0b355c1>]  [<ffffffffa0b355c1>] ath10k_ce_send+0x1d/0x15d [ath10k_pci]
RSP: 0018:ffff880215e19af8  EFLAGS: 00010292
RAX: ffff880215e19b10 RBX: 0000000000000000 RCX: 0000000000000018
RDX: 00000000d9ccf800 RSI: ffff8800c965ad00 RDI: 0000000000000000
RBP: ffff880215e19b58 R08: 0000000000000002 R09: 0000000000000000
R10: ffffffff812e1a23 R11: 0000000000000292 R12: 0000000000000018
R13: 0000000000000000 R14: 0000000000000002 R15: ffff88021562d700
FS:  0000000000000000(0000) GS:ffff88021fa80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000001a0d000 CR4: 00000000000407e0
Stack:
 d9ccf8000d47df40 ffffffffa0b367a0 ffff880215e19b10 0000000000000010
 ffff880215e19b68 ffff880215e19b28 0000000000000018 ffff8800c965ad00
 0000000000000018 0000000000000000 0000000000000002 ffff88021562d700
Call Trace:
 [<ffffffffa0b3251d>] ath10k_pci_hif_send_head+0xa7/0xcb [ath10k_pci]
 [<ffffffffa0b16cbe>] ath10k_htc_send+0x23d/0x2d0 [ath10k_core]
 [<ffffffffa0b1a169>] ath10k_wmi_cmd_send_nowait+0x5d/0x85 [ath10k_core]
 [<ffffffffa0b1aaef>] ath10k_wmi_cmd_send+0x62/0x115 [ath10k_core]
 [<ffffffff814e8abd>] ? __netdev_alloc_skb+0x4b/0x9b
 [<ffffffffa0b1c438>] ath10k_wmi_vdev_set_param+0x91/0xa3 [ath10k_core]
 [<ffffffffa0b0e0d5>] ath10k_mac_set_rts+0x3e/0x40 [ath10k_core]
 [<ffffffffa0b0e1d0>] ath10k_set_frag_threshold+0x5e/0x9c [ath10k_core]
 [<ffffffffa09d60eb>] ieee80211_reconfig+0x12a/0x7b3 [mac80211]
 [<ffffffff815a8069>] ? mutex_unlock+0x9/0xb
 [<ffffffffa09b3a40>] ieee80211_restart_work+0x5e/0x68 [mac80211]
 [<ffffffff810c01d0>] process_one_work+0x1d7/0x2fc
 [<ffffffff810c0166>] ? process_one_work+0x16d/0x2fc
 [<ffffffff810c06c8>] worker_thread+0x12e/0x1fb
 [<ffffffff810c059a>] ? rescuer_thread+0x27b/0x27b
 [<ffffffff810c5aee>] kthread+0xb5/0xbd
 [<ffffffff815a9220>] ? _raw_spin_unlock_irq+0x28/0x42
 [<ffffffff810c5a39>] ? __kthread_parkme+0x5c/0x5c
 [<ffffffff815ae04c>] ret_from_fork+0x7c/0xb0
 [<ffffffff810c5a39>] ? __kthread_parkme+0x5c/0x5c
Code: df ff d0 48 83 c4 18 5b 41 5c 41 5d 5d c3 55 48 89 e5 41 57 41 56 45 89 c6 41 55 41 54 41 89 cc 53 48 89
RIP  [<ffffffffa0b355c1>] ath10k_ce_send+0x1d/0x15d [ath10k_pci]
 RSP <ffff880215e19af8>
CR2: 0000000000000000
Reported-By: NBen Greear <greearb@candelatech.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Until now ath10k used a copy-by-value beacon
submission.

The new method passes a DMA address via WMI
command only. This command contains additional
metadata that fixes AP behaviour with regard
to powersave buffering.

This also fixes strange bug when multicast traffic
would freeze TX indefinitely.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Most channel switching logic has been implemented
already so this patch is pretty small. The patch
makes use of mac80211's vif->csa_active for AP CSA
handling.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Until now channel change wasn't propagating to FW
directly because operational channel is abstracted
by VDEVs and it wasn't really necessary since
ath10k implements hwscan and hwroc.

This effectively fixes STA CSA and allows for
future AP-like CSA as well.

kvalo: change error handling in ath10k_bss_info_changed()
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.x FW has no structure member sw_version_1. Thus,
both fw_version_release and fw_version_build are not
available. The provided fw_version_major is also wrong.
Fix this by using the fw_version from struct wiphy.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k handles UAPSD completly in the firmware.
When works in AP mode we have to configure
UAPSD params for each station. Without this
patch we configure UAPSD params before we
send peer assoc command to the FW, which was
wrong. Next FW didn't know what should be trigger
frame, couse UAPSD didn't work correctly in AP mode.
To configure UAPSD params correctly we have to
send them after peer assoc command.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware has a feature to track if the associated STA is not acking the frames.
When that happens, the firmware sends WMI_PEER_STA_KICKOUT_EVENTID event to the
host. Enable that to faster detect when a STA has left BSS without sending a
deauth frame.

Also set huge keepalive timeouts to avoid using the keepalive functionality in
the firmware.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Enable ap_ps_peer_param_cmdid for 10.x FW.
This is used mainly for AP UAPSD.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add set_bitrate_mask callback. Currently
ath10k HW is limited to handle only single
fixed rate setting or limit number of used
spatial streams.

Example:
iw wlanX set bitrates legacy-5 ht-mcs-5 vht-mcs-5 2:9
will setup VHT, nss=2, mcs=9

iw wlanX set bitrates legacy-5 18 ht-mcs-5 vht-mcs-5
will setup legacy, 18Mbps

iw wlanX set bitrates legacy-5 ht-mcs-5 3 vht-mcs-5
will setup HT, nss=1, mcs=3

iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9
will setup nss=1

iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9 2:0-9
will setup nss=2
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware dbglogs can be now enabled through fw_dbglog file. To enable all
possible log messages run:

echo 0xffffffff > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog

And to put back firmare defaults use 0x0:

echo 0x0 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Send firmware WMI debug logs to user space for further processing.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware can send simple ascii strings as debug messages using
WMI_DEBUG_PRINT_EVENTID, print those with ATH10K_DBG_WMI log level.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To not exceed number of allowed clients (AP mode), make sure to
check how many of them are already on the peers list.

10.X firmware support up to 127 peers, non-AP centric firmwares 16.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently ath10k is not using STA KICKOUT firmware functionality.
In order to avoid unwanted WMI_PEER_STA_KICKOUT_EVENT event this functionality
should be disabled when not used.
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add Kconfig option that allow DFS functionality.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This value is no longer used by mac80211, and practically no
driver ever set it to a correct value anyway, so remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>