Use the helper to check and restart autonegotiation for the marvell
fiber page negotiation setting.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use phy_modify_changed() to change the fiber advertisement register
rather than open coding this functionality.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use existing clause 37 advertising/link partner definitions rather than
private ones for the advertisement registers.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

marvell_read_status_page_an() always reads the PHY status register, but
marvell_update_link() has already done this.  Rather than wastefully
reading the register twice in quick succession, read it once in
marvell_read_status_page() and use the result for both.

This makes marvell_update_link() rather pointless, so move it into
marvell_read_status_page().
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than using negative logic:

	if (there is no link)
		set link = 0
	else
		set link = 1

use the more natural positive logic:

	if (there is link)
		set link = 1
	else
		set link = 0
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the initialisation of the link partner state earlier, inside
marvell_read_status_page(), so we don't have the same initialisation
scattered amongst the other files.  This is in a similar place to
the genphy implementation, so would result in the same behaviour if
a PHY read error occurs.

This allows us to get rid of marvell_read_status_page_fixed(), which
became a pointless wrapper around genphy_read_status_fixed().
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rearrange the Marvell PHY driver to use genphy_read_lpa() rather than
open-coding this functionality.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two drivers and generic code which contain exactly the same
code to read the status of a PHY operating without autonegotiation
enabled. Rather than duplicate this code, provide a helper to read
this information.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a helper for restarting autonegotiation(), similar to the clause 45
variant.  Use it in __genphy_config_aneg()
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several drivers code their own version of this, working from the LPA
register, after setting the ethtool link partner advertisement bitmask.
Use the generic function instead.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove initialisers that set .aneg_done to genphy_aneg_done - this is
the default for clause 22 PHYs, so the initialiser is redundant.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit e45d1f52 ("net: phylink: support Clause 45 PHYs on SFP+
modules") added a workaround to support clause 45 PHYs which
dynamically switch their interface mode on SFP+ modules.  This was
implemented by validating the PHYs supported/advertising using
PHY_INTERFACE_MODE_NA, rather than the specific interface mode that
we attached the PHY with.

However, we already have a situation where phylink is used to connect
a Marvell 88X3310 PHY which also behaves in exactly the same way, but
which seemingly doesn't need this.  The reason seems to be that the
mvpp2 driver sets a whole bunch of link modes for
PHY_INTERFACE_MODE_10GKR down to 10Mb/s, despite 10GBASE-R not actually
supporting anything but 10Gb/s speeds.

When testing with drivers that (correctly) take the mvneta approach,
where the validate() method only returns what can be supported /
advertised for the specified link mode, we find that Clause 45 PHYs do
not behave as we expect: their advertisement is restricted to what
the current link will support, rather than what the PHY supports
through its dynamic switching.

Extend this workaround to all such cases; if we have a Clause 45 PHY
attaching via any means, except in USXGMII, XAUI and RXAUI which are
all unable to support this dynamic switching or have other solutions
to it, then we need to validate using PHY_INTERFACE_MODE_NA.

This should allow mvpp2 to switch to a more conformant validate()
implementation.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While testing ethtool with the Methode DM7052 module, it was noticed
that attempting to set the advertising mask results in the mask being
truncated to the support offered by the currently chosen PHY interface
mode.

When a PHY dynamically changes the PHY interface mode, limiting the
advertising mask in this way is not correct - if the PHY happened to
negotiate 10GBASE-T, and selected 10GBASE-R as the host interface, we
don't want to restrict the advertisement to just 10GBASE-* modes.

Rework setting the advertisement to take account of this; do not pass
the requested advertisement through phylink_validate(), but rely on
the advertisement restriction (supported mask) set when the PHY was
initially setup.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

of_phy_attach() hides the return value of phy_attach_direct(), forcing
us to return a "generic" ENODEV error code that is indistinguishable
from the lack-of-phy-property case.

Switch to using of_phy_find_device() to find the PHY device, and then
propagating any phy_attach_direct() error back to the caller.

Link: https://lore.kernel.org/lkml/20191210113829.GT25745@shell.armlinux.org.ukSigned-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Fixes coccicheck warning:

drivers/net/phy/dp83869.c:337:2-3: Unneeded semicolon
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: Nzhengbin <zhengbin13@huawei.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Some 1000BASE-T PHY modules take a while for the PHY to wake up.
Retry the probe a number of times before deciding that the module has
no PHY.

Tested with:
 Sourcephotonics SPGBTXCNFC - PHY takes less than 50ms to respond.
 Champion One 1000SFPT - PHY takes about 200ms to respond.
 Mikrotik S-RJ01 - no PHY
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename sm_retries as sm_fault_retries, as this is what this member is
tracking.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some SFP+ modules have a Clause 45 PHY onboard, which is accessible via
the normal I2C address.  Detect 10G BASE-T PHYs which may have an
accessible PHY and probe for it.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a rudimentary Clause 45 driver for the BCM84881 PHY, found on
Methode DM7052 SFPs.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Broadcom BCM84881 does not appear to send the SGMII control word
when operating in SGMII mode, which causes network adapters to fail
to link with the PHY, or decide to operate at fixed 1G speed, even if
the PHY negotiated 100M.

Work around this by detecting the Broadcom BCM84881 and switch to phy
mode rather than inband mode.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Knowing whether we need to delay the MAC configuration because a module
may have a PHY is useful to phylink to allow NBASE-T modules to work on
systems supporting no more than 2.5G speeds.

This commit allows us to delay such configuration until after the PHY
has been probed by recording the parsed capabilities, and if the module
may have a PHY, doing no more until the module_start() notification is
called.  At that point, we either have a PHY, or we don't.

We move the PHY-based setup a little later, and use the PHYs support
capabilities rather than the EEPROM parsed capabilities to determine
whether we can support the PHY.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split out the configuration step from phylink_sfp_module_insert() so
we can re-use this later.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split link_an_mode between the configured setting and the current
operating setting.  This is an important distinction to make when we
need to configure PHY mode for a plugged SFP+ module that does not
use in-band signalling.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some SFP+ modules have Clause 45 PHYs embedded on them, which need a
little more handling in order to ensure that they are correctly setup,
as they switch the PHY link mode according to the negotiated speed.

With Clause 22 PHYs, we assumed that they would operate in SGMII mode,
but this assumption is now false.  Adapt phylink to support Clause 45
PHYs on SFP+ modules.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to support Clause 45 PHYs on SFP+ modules, which have an
indeterminant phy interface mode, we need to be able to call
phylink_bringup_phy() with a different interface mode to that used when
binding the PHY. Reduce __phylink_connect_phy() to an attach operation,
and move the call to phylink_bringup_phy() to its call sites.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some SFP+ modules have PHYs on them just like SFP modules do, except
they are Clause 45 PHYs.  The I2C protocol used to access them is
modified slightly in order to send the device address and 16-bit
register index.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move phy_start() and phy_stop() into the module_start and module_stop
notifications in phylink, rather than having them in the SFP code.
This gives phylink responsibility for controlling the PHY, rather
than having SFP start and stop the PHY state machine.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When dealing with some copper modules, we can't positively know the
module capabilities are until we have probed the PHY. Without the full
capabilities, we may end up failing a module that we could otherwise
drive with a restricted set of capabilities.

An example of this would be a module with a NBASE-T PHY plugged into
a host that supports phy interface modes 2500BASE-X and SGMII. The
PHY supports 10GBASE-R, 5000BASE-X, 2500BASE-X, SGMII interface modes,
which means a subset of the capabilities are compatible with the host.

However, reading the module EEPROM leads us to believe that the module
only supports ethtool link mode 10GBASE-T, which is incompatible with
the host - and thus results in the module being rejected.

This patch adds an extra notification which are triggered after the
SFP module's PHY probe, and a corresponding notification just before
the PHY is removed.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SFF-8024 is used to define various constants re-used in several SFF
SFP-related specifications.  Split these constants from the enum, and
rename them to indicate that they're defined by SFF-8024.

Add and use updated SFF-8024 extended compliance code definitions for
10GBASE-T, 5GBASE-T and 2.5GBASE-T modules.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't need the EEPROM ID to derive the phy interface mode as we can
derive it merely from the ethtool link modes.  Remove the EEPROM ID
argument to sfp_select_interface().
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 100BASE-FX and 100BASE-LX support assumes a PHY is present; this
is probably an incorrect assumption. In any case, sfp_parse_support()
will fail such a module. Let's stop pretending we support these
modules.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This code changes the TI specific ti,fifo-depth to the common
tx-fifo-depth property.  The tx depth is applicable for both RGMII and
SGMII modes of operation.

rx-fifo-depth was added as well but this is only applicable for SGMII
mode.

So in summary
if RGMII mode write tx fifo depth only
if SGMII mode write both rx and tx fifo depths

If the property is not populated in the device tree then set the value
to the default values.
Signed-off-by: NDan Murphy <dmurphy@ti.com>
Reported-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Nokia GPON module can hold tx-fault active while it is initialising
which can take up to 60s. Avoid this causing the module to be declared
faulty after the SFP MSA defined non-cooled module timeout.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit ef87f7da ("net: phy: dp83867: move dt parsing to probe")
causes regression on TI dra71x-evm and dra72x-evm, where DP83867 PHY is
used in "rgmii-id" mode - the networking stops working.
Unfortunately, it's not enough to just move DT parsing code to .probe() as
it depends on phydev->interface value, which is set to correct value abter
the .probe() is completed and before calling .config_init(). So, RGMII
configuration can't be loaded from DT.

To fix and issue
- move RGMII validation code to .config_init()
- parse RGMII parameters in dp83867_of_init(), but consider them as
optional.

Fixes: ef87f7da ("net: phy: dp83867: move dt parsing to probe")
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver forgets to call pci_release_regions() in remove like that
in probe failure.
Add the missed call to fix it.
Signed-off-by: NChuhong Yuan <hslester96@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The referenced commit below allowed more than one hwmon device to be
created per SFP, which is definitely not what we want. Avoid this by
only creating the hwmon device just as we transition to WAITDEV state.

Fixes: 139d3a21 ("net: sfp: allow modules with slow diagnostics to probe")
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When unbinding, we don't correctly tear down the module state, leaving
(for example) the hwmon registration behind. Ensure everything is
properly removed by sending a remove event at unbind.

Fixes: 6b0da5c9 ("net: sfp: track upstream's attachment state in state machine")
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was reported [0] that since the referenced commit a warning is
triggered in phylib that complains about paged operations being used
with a PHY driver that doesn't support this. The commit isn't wrong,
just for one chip version (RTL8105e) no dedicated PHY driver exists
yet. So add the missing PHY driver.

[0] https://bugzilla.kernel.org/show_bug.cgi?id=202103

Fixes: 3a129e3f ("r8169: switch to phylib functions in more places")
Reported-by: Njhdskag3 <jhdskag3@tutanota.com>
Tested-by: Njhdskag3 <jhdskag3@tutanota.com>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>