Skip to content

K
Kernel

openeuler / Kernel
接近 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 07 10月, 2012 1 次提交
    • L
      ACPI: Add new sysfs interface to export device description · d1efe3c3
      由 Lance Ortiz 提交于 
      Add support to export the device description obtained from the ACPI _STR
method, if one exists for a device, to user-space via a sysfs interface.
This new interface provides a standard and platform neutral way for users
to obtain the description text stored in the ACPI _STR method.  If no
_STR method exists for the device, no sysfs 'description' file will be
created.  The 'description' file will be located in the /sys/devices/
directory using the device's path.

/sys/device/<bus>/<bridge path>/<device path>.../firmware_node/description

Example:

/sys/devices/pci0000:00/0000:00.07.0/0000:0e:00.0/firmware_node/description

It can also be located using the ACPI device path, for example:

/sys/devices/LNXSYSTM:00/device:00/ACPI0004:00/PNP0A08:00/device:13/device:15/description
/sys/devices/LNXSYSTM:00/device:00/ACPI0004:00/ACPI0004:01/ACPI0007:02/description

Execute the 'cat' command on the 'description' file to obtain the
description string for that device.

This patch also includes documentation describing how the new sysfs
interface works

Changes from v1-v2 based on comments by Len Brown and Fengguang Wu
* Removed output "No Description" and leaving a NULL attribute if the
_STR method failed to evaluate.

* In acpi_device_remove_files() removed the redundent check of
dev->pnp.str_obj before calling free.  This check triggered a message
from smatch.
Signed-off-by: NLance Ortiz <lance.ortiz@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
      d1efe3c3
  3. 06 10月, 2012 9 次提交
  5. 03 10月, 2012 1 次提交
  7. 02 10月, 2012 10 次提交
  9. 01 10月, 2012 3 次提交
    • T
      dt: Document general interrupt controller bindings · acc20979
      由 Thierry Reding 提交于 
      In order to use a device as interrupt controller, it needs to be marked
with the DT interrupt-controller property. This commit adds rudimentary
documentation about the required standard properties and describes the
most commonly used interrupt specifiers.

Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
      acc20979
    • S
      mfd: smsc: Add support for smsc gpio io/keypad driver · 8284328c
      由 Sourav Poddar 提交于 
      smsc ece1099 is a keyboard scan or gpio expansion device.
The patch create keypad and gpio expander child for this
multi function smsc driver.

Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
      8284328c
    • S
      pinctrl: add bcm2835 driver · e1b2dc70
      由 Simon Arlott 提交于 
      The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.

Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.

Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
  datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
  implemented are driven by the board, not the GPIO HW block, so don't
  really make sense of a HW block binding, were in general incomplete
  (since they could only know about the few pins hard-coded into the
  Raspberry Pi B board design and not the uncommitted GPIOS), and are
  better represented simply by not writing incorrect data into pin
  configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
  glitches; defer this to gpio_set_direction(). Consequently, removed
  empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
  IRQ handler, thus fixing an issue where the code was indexing into
  enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
  spin_lock_irqsave() and so guarantees it doesn't run concurrently
  with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
  bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
  decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
  directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
  core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
  descriptive.
* Simplified remove(); removed call to non-existent
  pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
  base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NChris Boot <bootc@bootc.net>
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      e1b2dc70
  11. 29 9月, 2012 1 次提交
  13. 28 9月, 2012 2 次提交
  15. 27 9月, 2012 11 次提交
  17. 26 9月, 2012 2 次提交