The patch brings infrared remote support for some cx88 based cards.
Such as:
TeVii S460,S420; Omicom SS4; SatTrade ST4200;
TBS 8920,8910; Prof 7300,6200.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This adds an soc-camera / v4l2-subdev driver for the RJ54N1CB0C CMOS camera
sensor from Sharp. The sensor is very picky about initialisation and
configuration sequences. The driver limits artificially maximum window size by
800x600, although the sensor supports 1600x1200. Sizes above 800x600 don't seem
to work correctly, besides, examples from the system integrator use sizes above
640x480 only for still photography. Unfortunately, I had to use "magic"
register-value pairs for undocumented and "reserved" registers. This version of
the driver also omits some functionality, like cropping, which hasn't been
sufficiently tested yet and will be added later.

 create mode 100644 drivers/media/video/rj54n1cb0c.c
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If CEU driver can not receive data from camera,
CETCR has VBP error state.
Then, CEU is stopped and cure operation is needed.
This patch add VBP error cure operation.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add comment about the meaning of the fixed JPEG header bytes used to
create each image.
Signed-off-by: NMarton Nemeth <nm127@freemail.hu>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove redundant register page switching to page 0 when changing the
color control.
Signed-off-by: NMarton Nemeth <nm127@freemail.hu>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The length check in reg_w_var() function is because the buffer contents
is copied to gspca_dev->usb_buf which has the size of USB_BUF_SZ bytes as
defined in drivers/media/video/gspca/gspca.h. Replace the number with
symbol for better readability and maintainability.
Signed-off-by: NMarton Nemeth <nm127@freemail.hu>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Change the magic values 0, 254 and 255 to END_OF_SEQUENCE, LOAD_PAGE4 and
LOAD_PAGE3 respectively for better source code readability.
Signed-off-by: NMarton Nemeth <nm127@freemail.hu>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Change the magic value 0xaa to SKIP for better understandability.
Signed-off-by: NMarton Nemeth <nm127@freemail.hu>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NRafal Milecki <zajec5@gmail.com>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Display i2c adapter id, address and master / slave role in debug output.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert tda18271_rf_tracking_filter_cal.rf_[ab][12] from int to s32.
Convert tda18271_priv.tm_rfcal from unsigned int to u8.
Cast subtractions between u32 values as s32.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use temporary variables for signed calulations between unsigned values
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This adds a forgotten module_param macro needed to set a deemphasis of 50us.
It is the standard setting for commercial FM radio broadcasts outside the US.
Signed-off-by: NHenk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Allow dvb-usb adapter drivers to specify a fe_ioctl_override callback
to enable device-specific handling of DVB frontend operations.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

override set_frontend to allow rf input path switching on the HVR1275
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This changes adds IR Rx keypress input event handling to the CX23885 module.
This change specifically only adds input handling for IR devices implemented as
v4l2_subdevices, using only the pulse width mode (for now), and only with
RC-5 remotes.  The V4L-DVB infrastructure is missing too much to support RC-6
mode 6A as used in many media center remotes.   The grey Hauppauge RC-5 remote
and HVR-1850 IR receiver work now.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add integrated IR subdevice interrupt and notification handling.  This is in
preparation of input keypress handling changes for the cx23885 module.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This change completes the v4l2_subdev implementation for IR receive for the
IR controller built into the CX23888.

This changes almost completes the IR transmit side also, but doesn't.  Instead
notes in the comments describe what needs to be done for IR Tx to work in the
subdevice implementation.

The current Tx behavior is skeletal and benign.  If left alone, it does nothing.
It will only ever generate a Tx interrupt on Tx init by a caller or when the
tx_write() method is called.  The ISR, when called, will then disable the Tx
FIFO service interrupt.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add v4l2_subdev_ir_ops and IR notify defines for v4l2_device.  This change
is specifically needed at this time to support the integrated IR controller in
the CX2388[58] chips.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The prior mechanism wasn't reliable with the cx23887. This new mechanism
tests correctly against cx23885, 7 and 8 based products.
Signed-off-by: NSteven Toth <stoth@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

For the IR controller on the CX23888 to work for the HVR-1850 and in
general, the A/V core must be initialized to get the VID_CLK going.
The VID_CLK is the timing reference for the CX23888's integrated
IR controller.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The SYS and AUX PLLs need to be initialized to different values based on
the chip: CX23885, CX23887, CX23888, as each uses a different crystal
frequency: 28.6363 MHz, 25.0 MHz, 50.0 MHz.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Separate out the set_audclk_freq() function into separate functions for the
four families of cores.  These cores all use slightly different sample clock
schemes and may be assuming slightly (+/- 3 Hz) different reference frequencies.
The code resuse was not worth the maintenance and testing headache of have all
chips use the same function peppered with conditional logic.

Added comments on how PLL and SRC parameters values are computed.  Fixed a few
bugs related to the shared code having a large number of conditional statements.
Noted inconsistencies with FIXME in the comments.

This is done in preparation for getting the CX2388[578] PLL/clock setting logic
cleaned up for CX23888 analog video and IR (which need the VID PLL set right).
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Change logic to check for various chip or core families to inline functions.
Checks for specific chips should be made against the state->id field now.  This
is in preparation for chip/core specific code for setting up PLLs for the
CX2388[578] family of cores, that all run with different crystal frequencies.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add improved logic to detect the exact CX2388[578] A/V core that is being
probed.  Also cleaned up detection and logging for CX2310[12], CX2583[67],
and CX2584[0123] cores and chips.

Also added code to identify a CX2388[578] A/V decoder core that is not
responding properly.  Typical symptoms include registers 0x00-0xff
responding properly but all other registers returning the same value
(0x13 and 0x5 have been observed).  This state will cause proper detection of
'885 vs. '887 vs. '888 to fail and the chip won't respond to get configured
properly anyway.  I have no method of reseting the core to a working state at
this time; but I didn't try too hard to work one out either.  The problem
likely only occurs in development.  I suspect configuring the SYS PLL VCO to
oscillate too slowly (286.3 MHz?) before post divide may be the root cause,
when encountered.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This change adds a skeletal implementation of a v4l2_subdevice to provide
encapsulation and abstraction of the CX23888's integrated consumer infrared
controller.  This change also instantiates the cx23888_ir subdev for the
HVR-1850 which has IR hardware physically wired up to a CX23888.

The cx23888_ir subdev code is being written with long-term objectives to:
1. port it to the cx25840 module for the CX2584x, CX2583x, CX23885, & CX231xx
   IR controllers
2. possibly port it to the cx18 module for the CX23418 IR controller
3. have the IR subdevice accessed abstractly in the cx23885 module, so the
   driver can ignore the difference between the CX23885 and CX23888.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This changes corrects the ioctl() operations for both the CX2388[578] analog
video and MPEG video device nodes to properly and consistently support
VIDIOC_G_CHIP_IDENT, VIDIOC_DBG_G_REGISTER and VIDIOC_DBG_S_REGISTER ioctl()s.

This caused some ioctl() support routines to be broken out into a separate
source file.

Now v4l2-dbg can be used to manipulate CX2388[578] and CX23417 registers
including the CX2388[57] functions handled by the cx25840 module.

This was done in anticipation of developing a new v4l2_subdev for the
integrated IR controller of the CX23888.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add identifiers for CX2388[578] chips, CX2310[012] chips, integrated
A/V decoders cores, integrated IR controller core, and the CX23417
MPEG encoder.  The cx23885 module and cx25840 module will use these
identifiers in upcoming changes.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The board support has been validated by the user, so get rid of the warning
that shows up on board load.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Dmitri's patch for the Behold X7 didn't use the #define I had setup for
XC5000_RADIO_FM1, so cut over to using that instead of "1".
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for the digital side of the Behold X7
Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make analog audio, dvb and the remote work on a Terratec Cinergy Hybrid
XS (em2882).

Note by djh: Thanks go out fo Andrej Suligoi for his contribution in providing
and testing pretty much the exact same patch as provided by Uros.  Between
the two of them, they got all the core functionality working for the device.

Cc: Andrej Suligoi <suligoi@gmail.com>
Signed-off-by: NUroš Vampl <mobile.leecher@gmail.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Seems that the reference design used for the KWorld 2800d switched from the
em2860 to em2862, so we need to add the new USB id (and the i2c hash remains
so all we need is the default em2862 id.

Thanks to Ian Young for reporting the issue and testing the fix.

Cc: Ian Young <ian@duffrecords.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove hard-coded definition of the xc5000 FM radio input, making it a
parameter passed in when doing the attach call.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add FM radio for the xc5000 silicon tuner chip.
Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>