Pass around requests to carry context deeper in callchain.
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It is found that i915 will not reset gpu under execlist mode when
unload module. that will lead to some issues when unload/load module
with different submission mode. e.g. from execlist mode to ring
buffer mode via loading/unloading i915. Because HW is not in a reset
state and registers are not clean under such condition.
Signed-off-by: NNiu,Bing <bing.niu@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In this WA we need to set GEN8_L3SQCREG4[21:21] and reset it after PIPE_CONTROL
instruction but there is a slight complication as this is applied in WA batch
where the values are only initialized once.
Dave identified an issue with the current implementation where the register value
is read once at the beginning and it is reused; this patch corrects this by saving
the register value to memory, update register with the bit of our interest and
restore it back with original value.

This implementation uses MI_LOAD_REGISTER_MEM which is currently only used
by command parser and was using a default length of 0. This is now updated
with correct length and moved to appropriate place.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now all the functions called by other files check whether FBC has been
initialized. This allows us to drop the checks on the static
functions.

v2:
 - s/HAS_FBC/dev_priv->display.enable_fbc/ everywhere but the init
   function (Chris).
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Everything is covered either by fbc.lock or mm.stolen_lock, and
intel_fbc.c is already responsible for grabbing the appropriate locks
when it needs them.
Reviewed-by: NChris wilson <chris@chris-wilson.co.uk>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So don't grab the lock before calling the function.
Reviewed-by: NChris wilson <chris@chris-wilson.co.uk>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So release the lock earlier.
Reviewed-by: NChris wilson <chris@chris-wilson.co.uk>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Make sure we're not going to have weird races in really weird cases
where a lot of different CRTCs are doing rendering and modesets at the
same time.

With this change and the stolen_lock from the previous patch, we can
start removing the struct_mutex locking we have around FBC in the next
patches.

v2:
 - Rebase (6 months later)
 - Also lock debugfs and stolen.
v3:
 - Don't lock a single value read (Chris).
 - Replace lockdep assertions with WARNs (Daniel).
 - Improve commit message.
 - Don't forget intel_pre_plane_update() locking.
v4:
 - Don't remove struct_mutex at intel_pre_plane_update() (Chris).
 - Add comment regarding locking dependencies (Chris).
 - Rebase after the stolen code rework.
 - Rebase again after drm-intel-nightly changes.
v5:
 - Rebase after the new stolen_lock patch.

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v4)
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Which should protect dev_priv->mm.stolen usage. This will allow us to
simplify the relationship between stolen memory, FBC and struct_mutex.

v2:
  - Rebase after the stolen_remove_node() dev_priv patch move.
  - I realized that after we fixed a few things related to the FBC CFB
    size checks, we're not reallocating the CFB anymore with FBC
    enabled, so we can just move all the locking to i915_gem_stolen.c
    and stop worrying about freezing all the stolen alocations while
    freeing/rellocating the CFB. This allows us to fix the "Too
    coarse" observation from Chris.
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the abstractions created by the last patch, we can move this code
and the only thing inside intel_fbc.c that knows about dev_priv->mm is
the code that reads stolen_base.

We also had to move a call to i915_gem_stolen_cleanup_compression()
- now called intel_fbc_cleanup_cfb() - outside i915_gem_stolen.c.

v2:
  - Rebase after the remove_node() changes on the previous patch.
Requested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We want to move the FBC code out of i915_gem_stolen.c, but that code
directly adds/removes stolen memory nodes. Let's create this
abstraction, so i915_gme_stolen.c is still in control of all the
stolen memory handling. The abstraction will also allow us to add
locking assertions later.

v2:
  - Add dev_priv as remove_node() argument since we'll need it later
    (Chris).
Requested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Kill the extra intel_pre_plane_update() I accidentally added in

 commit 852eb00d
 Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
 Date:   Wed Jun 24 22:00:07 2015 +0300

    drm/i915: Try to make sure cxsr is disabled around plane
    enable/disable

This fixes a load of warnings from the frontbuffer tracking.

Testcase: igt/kms_frontbuffer_tracking/fbc-1p-rte
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Adding support for did2, or the extended support display devices ID
list, increases the total to 15.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Make it easier to handle the extended didl. No functional changes.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Conform to same style as the rest of the driver.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Inluding extended didl and cpdl fields

Present since opregion version 3.0.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add an overview of the drm/i915 hotplug handling.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Clarify that audio enable/disable sequences are part of the modeset
sequence.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

drivers/gpu/drm/i915/intel_ddi.c: In function ‘intel_prepare_ddi’:
drivers/gpu/drm/i915/intel_ddi.c:517:6: warning:
‘ddi_translations_fdi’ may be used uninitialized in this function
[-Wmaybe-uninitialized]
   if (ddi_translations_fdi)
      ^
drivers/gpu/drm/i915/intel_ddi.c:446:30: note: ‘ddi_translations_fdi’
was declared here
  const struct ddi_buf_trans *ddi_translations_fdi;
                              ^

This line used to be there, but was removed by:

commit f8896f5d
Author: David Weinehall <david.weinehall@linux.intel.com>
Date:   Thu Jun 25 11:11:03 2015 +030
    drm/i915/skl: Buffer translation improvements

Cc: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Ensures that the batch buffer is executed by the resource streamer.
And will let userspace know whether Resource Streamer is supported in
the kernel.

v2: Don't skip 1<<15 for the exec flags (Jani Nikula)
v3: Use HAS_RESOURCE_STREAMER macro for execbuf validation (Chris Wilson)

(from getparam patch)

v2: Update I915_PARAM_HAS_RESOURCE_STREAMER so it's after
    I915_PARAM_HAS_GPU_RESET.
v3: Only advertise RS support for hardware that supports it.
v4: Add HAS_RESOURCE_STREAMER() macro (Chris)

Testcase: igt/gem_exec_params
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NAbdiel Janulgue <abdiel.janulgue@linux.intel.com>
[danvet: squash in getparam patch since it'd break bisect, suggested
by Chris.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

GEN8 and above uses Execlists by default instead of the legacy
ringbuffer for batch execution. This patch enables the resource
streamer bits when required.

Patch is based on the initial work by Minu Mathai <minu.mathai@intel.com>
This version also adds the required bits to enable GEN8 Resource
Streamer context save and restore for Execlists.

Cc: ville.syrjala@linux.intel.com
Signed-off-by: NAbdiel Janulgue <abdiel.janulgue@linux.intel.com>
Reviewed-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Also clarify comments on context size that the extra state for
Resource Streamer is included.

v2: Don't remove the extended save/restore enabled for older
    platforms. (Ville)
    Use new MI_SET_CONTEXT defines for HSW RS save/restore state
    instead of extended save/restore. (Daniel)
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NAbdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Adds support for enabling the resource streamer on the legacy
ringbuffer for HSW and GEN8.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NAbdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch contains changes based on 2 updates to the spec:
Port PLL VCO restriction raised up to 6700.
Port PLL now needs DCO amp override enable for all VCO frequencies.

v2: Sonika's review comment addressed
	- dcoampovr_en_h variable not required
Based on a discussion with Siva, the following changes have been made.
	- replace dco_amp var with #define BXT_DCO_AMPLITUDE
	- set pll10 in a single assignment

v3:
Move DCO amplitude default value to i915_reg.h. Suggested by Siva.
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com> [v2]
[danvet: Spell out BUN since not everyone knows what this means.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

HDMI 12bpc should be working fine now. Let it loose.

This reverts commit 5e3daaca.

v2: Rebased due to CHV/BXT port clock check improvemnts
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-and-tested-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CHV/BXT DPLL can't generate frequencies in the 216-240 MHz range.
Account for that when checking whether the HDMI port clock is valid.
This is particularly important for BXT since it can otherwise do
12bpc, and standard 1920x1080p60 CEA modes land right in the middle
of that range when the clock gets multiplied to account for 12bpc.

With the extra checks we will now filter out any mode where both
8bpc and 12bpc clock are within the gap. During modeset we then
pick whichever mode works, favoring 12bpc if both are possible.

12bpc isn't supported on CHV so we simply end up filtering out any
mode where the 8bpc port clock is in the gap.

v2: Fix crtc_clock vs. port_clock fumble in compute_config() (Imre)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-and-tested-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Increase the HDMI port minimum port clock from 20 to 25 MHz. This is
is the minimum listed in the DVI/HDMI specs, and it's also the
documented minimum DPLL frequency for most of our platforms.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-and-tested-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Take the HDMI 12bpc mode and pixel repeat into account when extracting
the dotclock from the hardware on DDI platforms.

Tested on HSW only.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-and-tested-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The drm_property_unreference_blob() function tests whether its argument
is NULL and then returns immediately.
Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Reviewed-by: NZhao Junwang <zhjwpku@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Previously we have pointed the page where the individual ppgtt
scratch structures refer to, to be the instance which GGTT setup have
allocated. So it has been shared.

To achieve full isolation between ppgtts also in this regard,
allocate per ppgtt scratch page.

Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On CHT, changes are required for calculating the correct m,n & p with
minimal error +/- for the required DSI clock, so that the correct
dividor & ctrl values are written in cck regs for DSI. This patch has
been tested on CHT RVP with 1200 x 1920 panel.

v2 by Jani, rebased on earlier refactoring, original at [1].

[1] http://mid.gmane.org/1431368400-1942-5-git-send-email-rodrigo.vivi@intel.comSigned-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For MIPI panels requiring higher DSI clk, values needs to be added
in lfsr_converts table for getting the correct values of pll ctrl
and dividor values which gets programmed in cck regs, otherwise DSI
PLL does not get locked leading to no display on the MIPI panel.
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Nuke three copies of the same switch case.

Hopefully we can switch to a drm generic function later on, but that
will require us to swich to enum mipi_dsi_pixel_format first.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We first set the threshold value when we're allocating the CFB, and
then later at {ilk,gen7}_fbc_enable() we increment it in case we're
using 16bpp. While that is correct, it is dangerous: if we rework the
code a little bit in a way that allows us to call intel_fbc_enable()
without necessarily calling i915_gem_stolen_setup_compression() first,
we might end up incrementing threshold more than once. To prevent
that, increment a temporary variable instead.

v2: Rebase.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently only normal views were accounted which under-accounts
the usage as reported in debugfs.

Introduce new helper, i915_gem_obj_total_ggtt_size, and use it
from call sites which want to know how much GGTT space are
objects using.

v2: Single loop in i915_gem_get_aperture_ioctl. (Chris Wilson)

v3: Walk GGTT active/inactive lists in i915_gem_get_aperture_ioctl
    for better efficiency. (Chris Wilson, Daniel Vetter)

v4: Make i915_gem_obj_total_ggtt_size private to debugfs. (Chris Wilson)

v5: Change unsigned long to u64. (Chris Wilson)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Every other alloc_* function return the pointer to the page
they alloc. Follow the convention with scratch page also.
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Maintain base page handling functions in order of
alloc, free, init. No functional changes.

v2: s/Introduce/Maintain (Michel)
v3: Rebase

Cc: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

An earlier patch was added to reserve space in the ring buffer for the
commands issued during 'add_request()'. The initial version was
pessimistic in the way it handled buffer wrapping and would cause
premature wraps and thus waste ring space.

This patch updates the code to better handle the wrap case. It no
longer enforces that the space being asked for and the reserved space
are a single contiguous block. Instead, it allows the reserve to be on
the far end of a wrap operation. It still guarantees that the space is
available so when the wrap occurs, no wait will happen. Thus the wrap
cannot fail which is the whole point of the exercise.

Also fixed a merge failure with some comments from the original patch.

v2: Incorporated suggestion by David Gordon to move the wrap code
inside the prepare function and thus allow a single combined
wait_for_space() call rather than doing one before the wrap and
another after. This also makes the prepare code much simpler and
easier to follow.

v3: Fix for 'effective_size' vs 'size' during ring buffer remainder
calculations (spotted by Tomas Elf).

For: VIZ-5115
CC: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Reviewed-by: NTomas Elf <tomas.elf@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>