The code to clear fifo errors was incorrect and sending garbage
to the external phy. Removed the no longer used inline's funcs.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Minor whitespace cleanups.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The check for Yukon lite changes was restricting itself to
rev A3. It turns out that these changes are also true on A4
and later.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Cleanup the phy_lock deadlock because of relocking in the nway_reset path.
Reported by Francois Romieu.

Also, don't need to do irqsave/restore for blink,
just excluding bh is good enough.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Here is a fix for a typo, thanks Eliot Dresselhaus.
Since transmitter not active when device is down, it wasn't really noticed.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The SK-9E boards use the Marvell Yukon2 chipset which
is not supported by the skge driver. Thanks to Ralph Roesler
for noticing.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Using Genesis board, I get harmless error reports. Rather than console
error, turn it into a error counter.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

When leaving S3 state, the AGP bridge may not have all PCI configuration
registers set in the same way as they were at boot.  This should be fixed
by pci_restore_state - however, the APBASE register cannot be set to
conflict with the APSIZE register.  If APSIZE is larger than it was before
suspend, pci_restore_state will not restore APBASE correctly.  The attached
patch adds an extra item to the agp_bridge_data structure and uses it to
store the value of APBASE.  On resume, this is then written after APSIZE
has been set.  This patch only touches the path used for Intel chipsets
without integrated graphics, and may need to be extended to work with the
others.

Without this patch, I get the symptoms described in bug 4921 - APBASE ends
up overlapping various PCI devices, and as a result they fail to work after
resume.
Signed-off-by: NMatthew Garrett <mjg59@srcf.ucam.org>
Acked-by: NDave Jones <davej@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix inline assembly that gets miscompiled by gcc 4.
Signed-off-by: NGerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Close a small window where a device may be not operational again after senseid
finished and the "same device" check fails due to dev=0000 by checking for dnv
after stsch() by then setting the device to not operational.  (No need to
check for dnv in ccw_device_handle_oper() again since we don't do stsch() into
the subchannel's schib in the meantime and will get a crw anyway if the device
becomes not oper again).
Signed-off-by: NCornelia Huck <cohuck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The patch that introduced waiting for interrupts after resetting the reader
can cause the boot to fail because the system is waiting for an interrupt that
will never arrive.  Add code to check if an interrupt is supposed to arrive
before waiting endlessly.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Update default configuration of s390.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The #if/#ifdef cleanup exposed a bug in UML's ELF header processing.  With
this bug fixed, UML recognizes the vsyscall info coming from the host.  On
FC4, there is a vsyscall page low in the address space, which UML doesn't
provide.  This causes an infinite page fault loop and a hang on boot.

This patch works around that by making this look like a no-vsyscall system.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Do not use memcpy in fb_pad_aligned_buffer.  It is suboptimal because only
a few bytes are moved at a time.  Replace with a for-loop.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The patch addresses a problem with ACPI SCI interrupt entry, which gets
re-used, and the IRQ is assigned to another unrelated device.  The patch
corrects the code such that SCI IRQ is skipped and duplicate entry is
avoided.  Second issue came up with VIA chipset, the problem was caused by
original patch assigning IRQs starting 16 and up.  The VIA chipset uses
4-bit IRQ register for internal interrupt routing, and therefore cannot
handle IRQ numbers assigned to its devices.  The patch corrects this
problem by allowing PCI IRQs below 16.

Signed-off by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

>> vesafb: mode is 800x600x16, linelength=1600, pages=16
>> vesafb: scrolling: redraw
>> vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
>> mtrr: type mismatch for fc000000,1000000 old: write-back new: write-
>> combining

Range is already set to write-back, vesafb attempts to add a write-combining
mtrr (default for vesafb).

>> mtrr: size and base must be multiples of 4 kiB

This is a bug, vesafb attempts to add a size < PAGE_SIZE triggering
the messages below.

To eliminate the warning messages, you can add the option mtrr:2 to add a
write-back mtrr for vesafb.  Or just use nomtrr option.

1. Fix algorithm for finding the best power of 2 size with mtrr_add().

2. Add option to choose the mtrr type by extending the mtrr boot option:

   mtrr:n where n

        0 = no mtrr (equivalent to using the nomtrr option)
        1 = uncachable
        2 = write back
        3 = write combining (default)
        4 = write through
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add support for UARTs in MMIO space and clean up a little whitespace.

HP legacy-free ia64 machines need this.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

sync_tsc was using smp_call_function to ask the boot processor to report
it's tsc value.  smp_call_function performs an IPI_send_allbutself which is
a broadcast ipi.  There is a window during processor startup during which
the target cpu has started and before it has initialized it's interrupt
vectors so it can properly process an interrupt.  Receveing an interrupt
during that window will triple fault the cpu and do other nasty things.

Why cli does not protect us from that is beyond me.

The simple fix is to match ia64 and provide a smp_call_function_single.
Which avoids the broadcast and is more efficient.

This certainly fixes the problem of getting stuck on boot which was
very easy to trigger on my SMP Hyperthreaded Xeon, and I think
it fixes it for the right reasons.

Minor changes by AK
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

While reserving KVA for lmem_maps of node, we have to make sure that
node_remap_start_pfn[] is aligned to a proper pmd boundary.
(node_remap_start_pfn[] gets its value from node_end_pfn[])
Signed-off-by: NRavikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: NShai Fultheim <shai@scalex86.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It seems that I see a bug in hidinput_hid_event.  The check for NULL can never
work, becaue &hidinput->input is nonzero at all times.

Cc: <vojtech@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch does the same swap, i.e. use the ISO macro if (isoc).
Additionally, it fixes the return value - the usb_calc_bus_time function
returns the time in nanoseconds (I didn't notice that before) while the
HS_USECS and HS_USECS_ISO are microseconds.  This fixes the function to
return nanoseconds always, and adjusts ehci-q.c (the only high-speed
caller of the function) to wrap the call in NS_TO_US().
Signed-off-by: NDan Streetman <ddstreet@ieee.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Compare endpoint address to USB_ENDPOINT_DIR_MASK to determine endpoint
direction...

From: "Conger, Chris A." <CHRIS.A.CONGER@saic.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

USB (OHCI) Host driver for S3C2410/S3C2440 based systems
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Gigabyte GN-WLBZ201 wifi usb dongle works very well, using the zd1201
driver. the only missing part is that the corresponding usbid is not
declared. The following patch should fix this.

From: "Mathieu" <matt@minas-morgul.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch enables a support of KYOCERA AH-K3001V, one of the most
popular cell phone in Japan. This device has vendor specific ID but works
with acm driver by adding USB ID. This device already works on
FreeBSD and OS X by native USB ACM driver with USB ID added.

This device is probed as NO_UNION_NORMAL not to hang up when probing.
Signed-off-by: NMasahito Omote <omote@utyuuzin.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

below you will find the forgotten kmalloc check (sorry).
Signed-off-by: NMichael Hund <mhund@ld-didactic.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch handles a rarely-encountered failure mode in usbcore.  It's
legal for device_add to fail (although now it happens even more rarely
than before since failure to bind a driver is no longer fatal).  So when
we destroy the interfaces in a configuration, we shouldn't try to delete
ones which weren't successfully registered.  Also, failure to register an
interface shouldn't be fatal either -- I think; you may disagree about
this part of the patch.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The only uses of both variables were recently removed.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch fixes an information leak in the usbfs snoop facility:
uninitialized data from __get_free_page can be returned to userspace and
written to the system log.  It also improves the snoop output by printing
the wLength value.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

ftdi_sio: Fix timeouts in a couple of usb_control_msg() calls due to
change of units from jiffies to milliseconds in 2.6.12.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

ftdi_sio: Update RTS and DTR simultaneously, using a single control URB
instead of separate control URBs for RTS and DTR.  Reinhard Bergmann
observed time differences of up to 680 ms with his application on a
2.4.22 kernel when RTS and DTR were updated using separate control
URBs, which is unacceptable.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The attached patch adds the following new devices to the ftdi_sio driver:

* microHAM USB-Y6 and USB-Y8 devices submitted by Justin Burket (KL1RL).
* Evolution Robotics ER1 Control Module submitted by Shawn M.  Lavelle.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In the patch from:

http://www.uwsg.iu.edu/hypermail/linux/kernel/0506.3/0985.html

Is the the following line suppose inside the if CONFIG_PCI=n

  #define pci_dma_burst_advice(pdev, strat, strategy_parameter) do { } while (0)
Signed-off-by: NKumar Gala <kumar.gala@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The setup-bus code doesn't work correctly for configurations
with more than one display adapter in the same PCI domain.
This stuff actually is a leftover of an early 2.4 PCI setup code
and apparently it stopped working after some "bridge_ctl" changes.
So the best thing we can do is just to remove it and rely on the fact
that any firmware *has* to configure VGA port forwarding for the boot
display device properly.

But then we need to ensure that the bus->bridge_ctl will always
contain valid information collected at the probe time, therefore
the following change in pci_scan_bridge() is needed.
Signed-off-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There are ROMs reporting that their size exceeds their PCI ROM
resource window. This patch returns the minimum of the resource window
size or the size in the ROM.  An example of this breakage is the XGI
Volari Z7.
Signed-off-by: NJon Smirl <jonsmirl@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Patch against 2.6.12 to unhide SMBus on Toshiba Centrino laptops using
Intel 82855PM chipset.  Tested on Toshiba Tecra M2.
Signed-off-by: NDaniele Gaffuri <d.gaffuri@reply.it>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch was sent first time very long time ago,
but magically was disapeared, it probably exists
in your queue, but to be sure, I resend it.
If can not be applied cleanly after your w1 queue is flushed
into upstrem tree, just drop it.
Thanks.

Patch from Michael Farmbauer <michl@baldrian.franken.de>.
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The 24RF08 corruption prevention in the eeprom and max6875 drivers wasn't
complete. For one thing, the additional quick write should happen as soon
as possible and unconditionally, while both drivers had error paths before.
For another, when a given chip is forced, the core does not emit a quick
write, so a second quick write would cause the corruption rather than
prevent it.

I plan to move the corruption prevention in the core in the long run, so
that individual drivers don't have to care anymore. But I need to merge
i2c_probe and i2c_detect before I do (work in progress).
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Two log messages lack their trailing new line in i2c-core. I'd swear I had
fixed them already, but it seems not. Bonus: improved coding style.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>