This patch restructures how VFs are configured, and resources allocated.
Instead of freeing resources that were never allocated, and resetting
empty VFs that have never been created - the new flow will just allocate
resources for number of requested VFs based on the availability.

During VFs initialization process, global interrupt is disabled, and
rearmed after getting MSIX vectors for VFs. This allows immediate mailbox
communications, instead of delaying it till later and VFs.
PF communications resulted to using polling instead of actual interrupt.
The issue manifested when creating higher number of VFs (128 VFs) per PF.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we divide budget by the number of Rx queues per Rx ring
container in ice_napi_poll even if there is only 1. This is an
unnecessary divide for the normal case of 1 Rx ring per Rx ring
container. Fix this by using an unlikely() call in the case where we
actually need to divide.

Also, we will always set budget_per_ring even if there are no Rx rings
in the Rx ring container so we don't need to initialize it to 0.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently in ice_get_tx_pending we try to read a Tx ring's tail. This is
then compared with the software based head (next_to_clean) to determine
if we have pending work. This will never work because reading of the Tx
ring's tail is no longer supported. Fix this by using the software based
tail (next_to_use) to determine if there is pending work.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update driver version to 0.7.5
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As a result of refactoring of VF VSIs interrupts code, there is no
need to track its configuration status again with ICE_VF_STATE_CFG_INTR
flag - In fact, it is not being checked anywhere in the code right now, so
this patch removes the dead code as applicable to the flag.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This flag is not needed and is called every time we re-enable interrupts
in the hotpath so remove it. Also remove ice_vsi_req_irq() because it
was a wrapper function for ice_vsi_req_irq_msix() whose sole purpose was
checking the ICE_FLAG_MSIX_ENA flag.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since Tx rings are being managed by FW/NVM, Tx rings might have not been
set up or driver had already wiped them off - In that case, call to
disable LAN Tx queue is being returned as not in existence. This patch
makes sure we don't return unnecessary error for such scenario.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently if the call to ice_alloc_mapped_page() fails we jump to the
no_buf label, possibly call ice_release_rx_desc(), and return true
indicating that there is more work to do. In the success case we just
fall out of the while loop, possibly call ice_alloc_mapped_page(), and
return false saying we exhausted cleaned_count. This flow can be
improved by breaking if ice_alloc_mapped_page() fails and then the flow
outside of the while loop is the same for the failure and success case.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we are not reporting dropped counts at the port level to
ethtool or netlink. This was found when debugging Rx dropped issues
and the total packets sent did not equal the total packets received
minus the rx_dropped, which was very confusing. To determine dropped
counts at the port level we need to read the PRTRPB_RDPC register.
To fix reporting we will store the dropped counts in the PF's
rx_discards. This will be reported to netlink by storing it in the
PF VSI's rx_missed_errors signaling that the receiver missed the
packet. Also, we will report this to ethtool in the rx_dropped.nic
field.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In case there is a request from a VF to change its number of queues, and
the request was successful, we need to update number of queues
configured on the VF before updating corresponding VSI for that VF,
especially LAN Tx queue tree and TC update, otherwise, we would continued
to use old value of vf->num_vf_qs for allocated Tx/Rx queues...
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch uses allocated number of Tx queues per VSI to set up its
scheduling tree instead of using total number of available Tx queues.
Only PF VSIs have total number of allocated Tx queues equal to number
of available Tx queues, other VSIs have different number of queues
configured.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we bump the Rx tail and release/give buffers to hardware every
16 descriptors. This causes us to bump Rx tail up to 4 times per
napi_poll call. Also we are always bumping tail on an odd index and this
is a problem because hardware ignores the lower 3 bits in the QRX_TAIL
register. This is making it so hardware sees tail bumps only every 8
descriptors. Instead lets only bump Rx tail once per napi_poll if
the value aligns with hardware's expectations of the lower 3 bits being
cleared. Also only release/give Rx buffers once per napi_poll call.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds code to clear VFs enable status until reset is completed,
and Tx/Rx rings are setup. Without this patch, the code flow request Tx
queues to be disabled after reset, especially PFR - where VF VSI Tx rings
have already been wiped off in the NVM and result to adminq error based on
the call to disable Tx LAN queue in ice_reset_all_vfs function call.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The firmware reports an error when trying to configure a port with no
media. Instead of always configuring the port, check for media before
attempting to configure it. In the absence of media, turn off link and
poll for media to become available before re-enabling link.

Move ice_force_phys_link_state() up to avoid forward declaration.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ice_init_all_ctrlq and ice_shutdown_all_ctrlq functions create and
destroy the locks used to protect the send and receive process of each
control queue.

This is problematic, as the driver may use these functions to shutdown
and re-initialize the control queues at run time. For example, it may do
this in response to a device reset.

If the driver failed to recover from a reset, it might leave the control
queues offline. In this case, the locks will no longer be initialized.
A later call to ice_sq_send_cmd will then attempt to acquire a lock that
has been destroyed.

It is incorrect behavior to access a lock that has been destroyed.

Indeed, ice_aq_send_cmd already tries to avoid accessing an offline
control queue, but the check occurs inside the lock.

The root of the problem is that the locks are destroyed at run time.

Modify ice_init_all_ctrlq and ice_shutdown_all_ctrlq such that they no
longer create or destroy the locks.

Introduce new functions, ice_create_all_ctrlq and ice_destroy_all_ctrlq.
Call these functions in ice_init_hw and ice_deinit_hw.

Now, the control queue locks will remain valid for the life of the
driver, and will not be destroyed until the driver unloads.

This also allows removing a duplicate check of the sq.count and
rq.count values when shutting down the controlqs. The ice_shutdown_ctrlq
function already checks this value under the lock. Previously
commit dec64ff1 ("ice: use [sr]q.count when checking if queue is
initialized") needed this check to happen outside the lock, because it
prevented duplicate attempts at destroying the locks.

The driver may now safely use ice_init_all_ctrlq and
ice_shutdown_all_ctrlq while handling reset events, without causing the
locks to be invalid.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we are always setting prefena to 0. This is causing the
hardware to only fetch descriptors when there are none free in the cache
for a received packet instead of prefetching when it has used the last
descriptor regardless of incoming packets. Fix this by allowing the
hardware to prefetch Rx descriptors.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When interrupt tracking was refactored, during rebuild, the call to
ice_vsi_setup_vector_base() was inadvertently removed from the PF VSI
instead of being removed from the VF VSI. During reset, the failure to
properly setup the vector base generates a call trace. Correct this so
that resets/rebuilds properly complete.

Fixes: cbe66bfe ("ice: Refactor interrupt tracking")
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, ice_stat_update32 and ice_stat_update40 will limit the
value of the software statistic to 32 or 40 bits wide, depending on
which register is being read.

This means that if a driver is running for a long time, the displayed
software register values will roll over to zero at 40 bits or 32 bits.

This occurs because the functions directly assign the difference between
the previous value and current value of the hardware statistic.

Instead, add this value to the current software statistic, and then
update the previous value.

In this way, each time ice_stat_update40 or ice_stat_update32 are
called, they will increment the software tracking value by the
difference of the hardware register from its last read. The software
tracking value will correctly count up until it overflows a u64.

The only requirement is that the ice_stat_update functions be called at
least once each time the hardware register overflows.

While we're fixing ice_stat_update40, modify it to use rd64 instead of
two calls to rd32. Additionally, drop the now unnecessary hireg
function parameter.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for reporting link partner advertising when
ETHTOOL_GLINKSETTINGS defined. Get pause param reports the Tx/Rx
pause configured, and then ethtool issues ETHTOOL_GSET ioctl and
ice_get_settings_link_up reports the negotiated Tx/Rx pause. Negotiated
pause frame report per IEEE 802.3-2005 table 288-3.

$ ethtool --show-pause ens6f0
Pause parameters for ens6f0:
Autonegotiate:  on
RX:             on
TX:             on
RX negotiated:  on
TX negotiated:  on

$ ethtool ens6f0
Settings for ens6f0:
        Supported ports: [ FIBRE ]
        Supported link modes:   25000baseCR/Full
        Supported pause frame use: Symmetric
        Supports auto-negotiation: Yes
        Supported FEC modes: None BaseR RS
        Advertised link modes:  25000baseCR/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: None BaseR RS
        Link partner advertised link modes:  Not reported
        Link partner advertised pause frame use: Symmetric
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 25000Mb/s
        Duplex: Full
        Port: Direct Attach Copper
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: g
        Wake-on: g
        Current message level: 0x00000007 (7)
                               drv probe link
        Link detected: yes

When ETHTOOL_GLINKSETTINGS is not defined, get pause param reports the
negotiated Tx/Rx pause.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The audience for the Kernel driver-model is clearly Kernel hackers.
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> # ice driver changes

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

size = struct_size(instance, entry, count);

This code was detected with the help of Coccinelle.
Signed-off-by: N"Gustavo A. R. Silva" <gustavo@embeddedor.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Convert the various documents at the driver-model, preparing
them to be part of the driver-api book.

The conversion is actually:
  - add blank lines and identation in order to identify paragraphs;
  - fix tables markups;
  - add some lists markups;
  - mark literal blocks;
  - adjust title markups.

At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> # ice
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of using a local define for the LLDP ethertype, use the kernel
define ETH_P_LLDP.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch mostly capitalizes abbreviations in code comments. Fixed some
typos and removed some unnecessary newlines as well.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In ice_print_link_msg, add cases for 50GB and 100GB speeds. This
results in the right speed being reported on load, instead of
"Unknownbps".

When VF link if forced (in ice_set_pfe_link_forced), report
max speed 100GB.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Replace the use of the ICE_DBG_AQ_MSG bit when dumping firmware logging
messages with a separate distinct type ICE_DBG_FW_LOG. This is useful
so that developers may enable ICE_DBG_FW_LOG and get firmware logging
messages, without also dumping AdminQ messages at the same time.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add some details to the function header for ice_deinit_hw.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The define describing the bits for the struct field should be below
the field itself.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current specification has updates to the command formats for
manage MAC opcodes (opcodes 0x0107 and 0x0108) and get PHY caps
(opcode 0x0600). Update the code to reflect this.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For style consistency, use continue instead of an else block in
ice_pf_dcb_recfg.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change minimum number of descriptor count from 32 to 64. This is to have
a feature parity with previous Intel NIC drivers.
Signed-off-by: NPreethi Banala <preethi.banala@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add call to configure dropping egress LLDP packets in ice_vsi_setup
and remove the rule in ice_vsi_release.

Add calls to add/remove rule to route LLDP packets to default VSI when
FW LLDP engine is disabled/enabled and remove rule if applied during
ice_vsi_release.

In the function ice_add_eth_mac(), there is a line that hard codes the
filter info flag to TX. This is incorrect as this flag will be set by
the calling function that built the list of filters to add. So remove
the hard coded value.

This patch also contains a fix to stop treating the DCBx state of
"Not Started" as an error state that kicks DCB in SW mode. This will
address having non-cabled interfaces automatically go into SW mode
with the FW engine running.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Do not allocate memory for the Get PHY Abilities command data buffer when
it is not necessary, change one local variable to another to reduce the
number of de-references, reduce the scope of some local variables, and
reorder the code and change exit points to get rid of an unnecessary goto
label.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ice_cfg_vsi_lan returns a value of type enum ice_status. So
use a local of the same type to capture the return value.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds driver support for Forward Error Correction (FEC)
and ethtool handlers to set/get FEC params.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for virtchnl_vector_map.[rxq|txq]_map to use bitmap to
associate indicated queues with the specified vector. This support is
needed since the Windows AVF driver calls VIRTCHNL_OP_CONFIG_IRQ_MAP for
each vector and used the bitmap to indicate the associated queues.

Updated ice_vc_dis_qs_msg to not subtract one from
virtchnl_irq_map_info.num_vectors, and changed the VSI vector index to
the vector id. This change supports the Windows AVF driver which maps
one vector at a time and sets num_vectors to one. Using vectors_id to
index the vector array .

Add check for vector_id zero, and return VIRTCHNL_STATUS_ERR_PARAM
if vector_id is zero and there are rings associated with that vector.
Vector_id zero is for the OICR.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Consolidate adding unicast and broadcast MAC filters in a single new
function ice_init_mac_fltr.

Move ice_napi_del to ice_lib.c
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently in ice_free_vf_res() we are writing to the VFINT_DYN_CTLN
register in the PF's function space to disable all VF's interrupts. This
is incorrect because this register is only for use in the VF's function
space. This becomes obvious when seeing that the valid indices used for
the VFINT_DYN_CTLN register is from 0-63, which is the maximum number of
interrupts for a VF (not including the OICR interrupt). Fix this by
writing to the GLINT_DYN_CTL register for each VF. We can do this
because we keep track of each VF's first_vector_idx inside of the PF's
function space and the number of interrupts given to each VF.

Also in ice_free_vfs() we were disabling Rx/Tx queues after calling
pci_disable_sriov(). One part of disabling the Tx queues causes the PF
driver to trigger a software interrupt, which causes the VF's napi
routine to run. This doesn't currently work because pci_disable_sriov()
causes iavf_remove() to be called which disables interrupts. Fix this by
disabling Rx/Tx queues prior to pci_disable_sriov().
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a new function ice_trigger_sw_intr to trigger interrupts.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>