gp10b uses the new engine enumeration mechanism introduced in the Pascal
architecture. As a result, the copy engine, which used to be at index 2
for prior Tegra GPU instantiations, has now moved to index 0. Fix up the
index and also use the gp100 variant of the copy engine class because on
gp10b the PASCAL_DMA_COPY_B class is not supported.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

There are extra registers that need to be programmed to make the level 2
cache work on GP10B, such as the stream ID register that is used when an
SMMU is used to translate memory addresses.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

The GPUs found on Tegra SoCs have registers that can be used to read the
WPR configuration. Use these registers instead of reaching into the
memory controller's register space to read the same information.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

If the GPU clock has not had a rate set, initialize it to the maximum
clock rate to make sure it does run.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

When the GPU powergate is controlled by a generic power domain provider,
the reset will automatically be asserted and deasserted as part of the
power-ungating procedure.

On some Jetson TX2 boards, doing an additional assert and deassert of
the GPU outside of the power-ungate procedure can cause the GPU to go
into a bad state where the memory interface can no longer access system
memory.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

When Nouveau is instantiated on top of a platform device, the dev->pdev
field will be NULL and calling pci_disable_device() will crash. Move the
PCI disabling code to the PCI specific driver removal code.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

There is no BAR2 on GP10B and there is no need to map through BAR2
because all memory is shared between the GPU and the CPU. Add a custom
implementation of the fault sub-device that uses nvkm_memory_addr()
instead of nvkm_memory_bar2() to return the address of a pinned fault
buffer.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

The sizeof is currently on args.src and args.dst and should be on
*args.src and *args.dst. Fortunately these sizes just so happen
to be the same size so it worked, however, this should be fixed
and it also cleans up static analysis warnings

Addresses-Coverity: ("sizeof not portable")
Fixes: f268307e ("nouveau: simplify nouveau_dmem_migrate_vma")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This commit is seperate from the previous one to make it easier to
revert in the future. Basically, while working on making MSTOs per-head
as opposed to per-head-per-connector I discovered these lovely issues:

https://gitlab.freedesktop.org/xorg/xserver/merge_requests/277
https://gitlab.gnome.org/GNOME/mutter/issues/759

Note as well that Intel already has a temporary workaround for this in
their kernel driver. So, unfortunately we need to follow suit to avoid
causing a regression in userspace. Once these issues get fixed, this
commit should be reverted.
Signed-off-by: NLyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Currently, for every single MST capable DRM connector we create a set of
fake encoders, one for each possible head. Unfortunately this ends up
being a huge waste of encoders. While this currently isn't causing us
any problems, it's extremely close to doing so.

The ThinkPad P71 is a good example of this. Originally when trying to
figure out why nouveau was failing to load on this laptop, I discovered
it was because nouveau was creating too many encoders. This ended up
being because we were mistakenly creating MST encoders for the eDP port,
however we are still extremely close to hitting the encoder limit on
this machine as it exposes 1 eDP port and 5 DP ports, resulting in 31
encoders.

So while this fix didn't end up being necessary to fix the P71, we still
need to implement this so that we avoid hitting the encoder limit for
valid display configurations in the event that some machine with more
connectors then this becomes available. Plus, we don't want to let good
code go to waste :)

So, use less encoders by only creating one MSTO per head. Then, attach
each new MSTC to each MSTO which corresponds to a head that it's parent
DP port is capable of using. This brings the number of encoders we
register on the ThinkPad P71 from 31, down to just 15. Yay!
Signed-off-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

When drm_connector_helper_funcs->atomic_best_encoder is defined,
->best_encoder is ignored by the atomic modesetting helpers. That being
said, this hook is completely broken anyway - it always returns the
first msto for a given mstc, despite the fact it might already be in
use.

So, just get rid of it. We'll need this in a moment anyway, when we make
mstos per-head as opposed to per-connector.

Changes since v1:
* Fix typo in documentation - imirkin
Signed-off-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

The hardware supports either size. Also add checks to ensure that only
these two sizes may be used for supplying a LUT.
Signed-off-by: NIlia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Commit 5fde30a2684041f9820aa9dc4fbd0009a45076a9 in envytools modified
some of the Falcon V5 encodings, regenerate the relevant FW with this.

Also modify build rules to include SPDX header in generated files.

Tested on GM107, with no issues noted.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Merge tag 'amd-drm-next-5.6-2020-01-10-dp-mst-dsc' of git://people.freedesktop.org/~agd5f/linux into drm-next

amd-drm-next-5.6-2020-01-10-dp-mst-dsc:

drm:
- Add MST helper for PBN calculation of DSC modes
- Parse FEC caps on MST ports
- Add MST DPCD R/W functions
- Add MST helpers for virtual DPCD aux
- Add MST HUB quirk
- Add MST DSC enablement helpers

amdgpu:
- Enable MST DSC
- Add fair share algo for DSC bandwidth calcs
- Fix for 32 bit builds
Signed-off-by: NDave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200110214328.308549-1-alexander.deucher@amd.com

amd-drm-next-5.6-2020-01-09:

amdgpu:
- Enable DCN support on POWER
- Enable GFXOFF for Raven1 refresh
- Clean up MM engine idle handlers
- HDMI 2.0 audio fixes
- Fixes for some 10 bpc EDP panels
- Watermark fixes for renoir
- SR-IOV fixes
- Runtime pm robustness fixes
- Arcturus VCN fixes
- RAS fixes
- BACO fixes for Arcturus
- Stable pstate fixes for swSMU
- HDCP fixes
- PSP cleanup
- HDMI fixes
- Misc cleanups

amdkfd:
- Spread interrupt work across cores to reduce latency
- Topology fixes for APUs
- GPU reset improvements

UAPI:
- Enable DRIVER_SYNCOBJ_TIMELINE for vulkan
- Return better error values for kfd process ioctl
Signed-off-by: NDave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200109230338.8022-1-alexander.deucher@amd.com

drm-misc-next for v5.6:

UAPI Changes:

Cross-subsystem Changes:
- Convert simple panel bindings to a template.

Core Changes:
- Revert drm-bridge-state changes, it causes a dependency error
  between drm and drm_kms_helper.
- Fix when disabling crc's.
- Assorted Kconfig fixes.

Driver Changes:
- Add ddc symlinks to more drivers.
- Fix chained bridge handling in exynos and vc4.
- More clock rate fixes in sun4i.
- Add support for AUO B116XAK01, GiantPlus GPM940B0, Sony ACX424AKP,
  BOE NV140FHM-N49, Satoz SAT050AT40H12R2 and Sharp LS020B1DD01D panels.
- Assorted small bugfixes.
Signed-off-by: NDave Airlie <airlied@redhat.com>

From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1e8d4944-68d7-0df3-f39b-31f6fba22a2a@linux.intel.com

[why]
Compilation error "undefined reference to `__udivdi3'" was
thrown on i386 architecture.

[how]
Use div_u64 for unsigned long division instead of a divide operator.
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

the parameter is the mst manager, not the port.
Reviewed-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Otherwise we get undefined symbols.
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
We need to minimally initialize the remote aux channel, e.g. the
crc work struct of remote aux to dump the sink's DPRX CRCs in MST
setup.

[how]
Add helper that only initializes the crc work struct of the remote
aux, hooke crc work queue to 'drm_dp_aux_crc_work'. Then call this
helper in DP MST port initialization.
This, plus David Francis' patch [1], fix the issue of MST remote
aux DPCD CRCs read.

[1] https://patchwork.kernel.org/patch/11217941/

Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: NDavid (Dingchen) Zhang <dingchen.zhang@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Whenever a connector on an MST network is attached, detached, or
undergoes a modeset, the DSC configs for each stream on that
topology will be recalculated. This can change their required
bandwidth, requiring a full reprogramming, as though a modeset
was performed, even if that stream did not change timing.

Therefore, whenever a crtc has drm_atomic_crtc_needs_modeset,
for each crtc that shares a MST topology with that stream and
supports DSC, add that crtc (and all affected connectors and
planes) to the atomic state and set mode_changed on its state

v2: Do this check only on Navi and before adding connectors
and planes on modesetting crtcs

v3: Call the drm_dp_mst_add_affected_dsc_crtcs() to update
all affected CRTCs
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Whenever a connector on an MST network is changed or
undergoes a modeset, the DSC configs for each stream on that
topology will be recalculated. This can change their required
bandwidth, requiring a full reprogramming, as though a modeset
was performed, even if that stream did not change timing.

[how]
Adding helper to trigger modesets on MST DSC connectors
by setting mode_changed flag on CRTCs in the same topology
as affected connector

v2: use drm_dp_mst_dsc_aux_for_port function to verify
if the port is DSC capable

v3: - added _must_check attribute
    - removed topology manager check
    - fix typos and indentations
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Since for DSC MST connector's PBN is claculated differently
due to compression, we have to recalculate both PBN and
VCPI slots for that connector.

[how]
The function iterates through all the active streams to
find, which have DSC enabled, then recalculates PBN for
it and calls drm_dp_helper_update_vcpi_slots_for_dsc to
update connector's VCPI slots.

v2: - use drm_dp_mst_atomic_enable_dsc per port to
enable/disable DSC

v3: - Iterate through connector states from the state passed
    - On each connector state get stream from dc_state,
instead CRTC state
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

If driver fails to update update VCPI allocation during
compute_mst_dsc_configs_for_state - fail the function
by return early.
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

If there is limited link bandwidth on a MST network,
it must be divided fairly between the streams on that network

Implement an algorithm to determine the correct DSC config
for each stream

The algorithm:
This
     [                   ]          ( )
represents the range of bandwidths possible for a given stream.
The [] area represents the range of DSC configs, and the ()
represents no DSC. The bandwidth used increases from left to right.

First, try disabling DSC on all streams
     [                  ]          (|)
     [                     ]            (|)
Check this against the bandwidth limits of the link and each branch
(including each endpoint). If it passes, the job is done

Second, try maximum DSC compression on all streams
that support DSC
     [|         ]        ( )
     [|                ]         ( )
If this does not pass, then enabling this combination of streams
is impossible

Otherwise, divide the remaining bandwidth evenly amongst the streams
     [        |  ]         ( )
     [        |      ]        ( )

If one or more of the streams reach minimum compression, evenly
divide the reamining bandwidth amongst the remaining streams
     [    |] ( )
     [       |]   ( )
     [                 |   ]               ( )
     [                 |      ]                  ( )

If all streams can reach minimum compression, disable compression
greedily
     [      |]  ( )
     [        |]    ( )
     [                 ]                                (|)

Perform this algorithm on each full update, on each MST link
with at least one DSC stream on it

After the configs are computed, call
dcn20_add_dsc_to_stream_resource on each stream with DSC enabled.
It is only after all streams are created that we can know which
of them will need DSC.

Do all of this at the end of amdgpu atomic check.  If it fails,
fail check; This combination of timings cannot be supported.

v2: Use drm_dp_mst_atomic_check to validate bw for certain dsc
configurations

v3: Use dc_dsc_policy structure to get min and max bpp rate
for DSC configuration
Acked-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Need to calculate VCPI slots differently for DSC
to take in account current link rate, link count
and FEC.
[how]
Add helper to get pbn_div from dc_link
Acked-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
drm_dp_mst_atomic_check_topology_state() should be renamed
to reflect more specific type of check. Since it is verifying
payload allocation limit it should be renamed into
drm_dp_mst_atomic_check_vcpi_alloc_limit()
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Adding PBN attribute to drm_dp_vcpi_allocation structure to
keep track of how much bandwidth each Port requires.
Adding drm_dp_mst_atomic_check_bw_limit to verify that
state's bandwidth needs doesn't exceed available bandwidth.
The funtion is called in drm_dp_mst_atomic_check after
drm_dp_mst_atomic_check_topology_state to fully verify that
the proposed topology is supported.

v2: Fixing some typos and indenting
v3: Return correct error enums if no bw space available
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Adding a helper function to be called by
drivers outside of DRM to enable DSC on
the MST ports.

Function is called to recalculate VCPI allocation
if DSC is enabled and raise the DSC flag to enable.
In case of disabling DSC the flag is set to false
and recalculation of VCPI slots is expected to be done
in encoder's atomic_check.

v2: squash separate functions into one and call it per
port
v3: Fix comment typos
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
For DSC case we cannot use topology manager's PBN divider
variable. The default divider does not take FEC into account.
Therefore the driver has to calculate its own divider based
on the link rate and lane count its handling, as it is hw specific.

[how]
Pass pbn_div as an argument, which is used if its more than
zero, otherwise default topology manager's pbn_div will be used.
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Rework the dm_helpers_write_dsc_enable callback to
handle the MST case.

Use the cached dsc_aux field.
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

During MST mode enumeration, if a new dc_sink is created,
populate it with dsc caps as appropriate.

Use drm_dp_mst_dsc_aux_for_port to get the raw caps,
then parse them onto dc_sink with dc_dsc_parse_dsc_dpcd.
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

For DSC MST, sometimes monitors would break out
in full-screen static. The issue traced back to the
PPS generation code, where these variables were being used
uninitialized and were picking up garbage.

memset to 0 to avoid this
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Synaptics DP1.4 hubs (BRANCH_ID 0x90CC24) do not
support virtual DPCD registers, but do support DSC.
The DSC caps can be read from the physical aux,
like in SST DSC. These hubs have many different
DEVICE_IDs.  Add a new quirk to detect this case.

v2: Fix error when checking return of drm_dp_read_desc
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add drm_dp_mst_dsc_aux_for_port. To enable DSC, the DSC_ENABLED
register might have to be written on the leaf port's DPCD,
its parent's DPCD, or the MST manager's DPCD. This function
finds the correct aux for the job.

As part of this, add drm_dp_mst_is_virtual_dpcd. Virtual DPCD
is a DP feature new in DP v1.4, which exposes certain DPCD
registers on virtual ports.

v2: Remember to unlock mutex on all paths
v3: Refactor to match coding style and increase brevity
v4: - Check DSC capable MST sink connected directly to the device.
    - Check branch's port_parent to be set

Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This field on drm_dp_mst_branch was never filled

It is initialized to zero when the port is kzallocced.
When a port is added to the list, increment num_ports,
and when a port is removed from the list, decrement num_ports.

v2: remember to decrement on port removal
v3: don't explicitly init to 0
v4: move decrement of num_ports to unlink_port function
Reviewed-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Instead of having drm_dp_dpcd_read/write and
drm_dp_mst_dpcd_read/write as entry points into the
aux code, have drm_dp_dpcd_read/write handle both.

This means that DRM drivers can make MST DPCD read/writes.

v2: Fix spacing
v3: Dump dpcd access on MST read/writes
v4: Fix calling wrong function on DPCD write
v5: delete deprecated include of drmP.h
Reviewed-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

As of DP1.4, ENUM_PATH_RESOURCES returns a bit indicating
if FEC can be supported up to that point in the MST network.

The bit is the first byte of the ENUM_PATH_RESOURCES ack reply,
bottom-most bit (refer to section 2.11.9.4 of DP standard,
v1.4)

That value is needed for FEC and DSC support

Store it on drm_dp_mst_port
Reviewed-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

With DSC, bpp can be fractional in multiples of 1/16.

Change drm_dp_calc_pbn_mode to reflect this, adding a new
parameter bool dsc. When this parameter is true, treat the
bpp parameter as having units not of bits per pixel, but
1/16 of a bit per pixel

v2: Don't add separate function for this
v3: In the equation divide bpp by 16 as it is expected
not to leave any remainder
v4: Added DSC test parameters for selftest
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use filep->private_data to store a pointer to the kfd_process data
structure. Take an extra reference for that, which gets released in
the kfd_release callback. Check that the process calling kfd_ioctl
is the same that opened the file descriptor. Return -EBADF if it's
not, so that this error can be distinguished in user mode.
Signed-off-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NPhilip Yang <Philip.Yang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>