Miscellaneous Fixes:
- Fix the wrong variable name used for checking node active usage status
- Fix numerous duplicate log message numbers
- Fix change KERN_WARNING messages to KERN_INFO.
- Stop sending erroneous LOGO to fabric after vport is already terminated
- Fix HBQ allocates that were kalloc'ing w/ GFP_KERNEL while holding a lock.
- Fix gcc 4.3.2 compiler warnings and a sparse warning
- Fix bugs in handling unsolicited ct event queue
- Reorder some of the initial link up checks, to remove odd VPI states.
- Correct poor VPI handling
- Add debug messages
- Expand Update_CFG mailbox definition
- Fix handling of VPD data offsets
- Reorder loopback flags
- convert to use offsetof()
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Update driver for new SLI-3 features:
- interrupt enhancements
- lose adapter doorbell writes
- inlining support for FCP_Ixx cmds
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Miscellaneous Discovery fixes:
- Fix rejection followed by acceptance in handling RPL and RPS
  unsolicited events
- Fix for vport delete crash
- Fix PLOGI vs ADISC race condition
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This checks the errors the scsi-ml determined were retryable
and returns if we should fast fail it based on the request
fail fast flags.

Without the patch, drivers like lpfc, qla2xxx and fcoe would return
DID_ERROR for what it determines is a temporary communication problem.
There is no loss of connectivity at that time and the driver thinks
that it would be fast to retry at the driver level. SCSI-ml will however
sees fast fail on the request and DID_ERROR and will fast fail the io.
This will then cause dm-multipath to fail the path and possibley switch
target controllers when we should be retrying at the scsi layer.

We also were fast failing device errors to dm multiapth when
unless the scsi_dh modules think otherwis we want to retry at
the scsi layer because multipath can only retry the IO like scsi
should have done. multipath is a little dumber though because it
does not what the error was for and assumes that it should fail
the paths.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Multipath is best at handling transport errors. If it gets a device
error then there is not much the multipath layer can do. It will just
access the same device but from a different path.

This patch breaks up failfast into device, transport and driver errors.
The multipath layers (md and dm mutlipath) only ask the lower levels to
fast fail transport errors. The user of failfast, read ahead, will ask
to fast fail on all errors.

Note that blk_noretry_request will return true if any failfast bit
is set. This allows drivers that do not support the multipath failfast
bits to continue to fail on any failfast error like before. Drivers
like scsi that are able to fail fast specific errors can check
for the specific fail fast type. In the next patch I will convert
scsi.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This has qla2xxx use the new transport error values instead of
DID_BUS_BUSY. I am not sure if all the errors
in qla_isr.c I changed are transport related. We end up blocking/deleting
the rport for all of them so it is better to use the new transport error since
the fc classs will decide when to fail the IO.

With this patch if I pull a cable then IO that had reached
the driver, will be failed with DID_TRANSPORT_DISRUPTED (not including
tape). The fc class will then fail the IO when the fast io fail tmo
has fired, and the driver will flush any other commands running.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

If the target is blocked and fast io fail tmo has not fired
then we requeue with DID_TRANSPORT_DISRUPTED. Once that
tmo fires we fail with DID_TRANSPORT_FAILFAST.

v2
- seperate from
"fc class: unblock target after calling terminate callback"
to make it easier to review.
- Add JamesS's ack from list.
v2
- initial patch
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Acked-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch converts the iscsi drivers to the new host byte values.

v2
Drop some conversions. Want to avoid conflicts with other patches.
v1
initial patch.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Currently, if there is a transport problem the iscsi drivers will return
outstanding commands (commands being exeucted by the driver/fw/hw) with
DID_BUS_BUSY and block the session so no new commands can be queued.
Commands that are caught between the failure handling and blocking are
failed with DID_IMM_RETRY or one of the scsi ml queuecommand return values.
When the recovery_timeout fires, the iscsi drivers then fail IO with
DID_NO_CONNECT.

For fcp, some drivers will fail some outstanding IO (disk but possibly not
tape) with DID_BUS_BUSY or DID_ERROR or some other value that causes a retry
and hits the scsi_error.c failfast check, block the rport, and commands
caught in the race are failed with DID_IMM_RETRY. Other drivers, may
hold onto all IO and wait for the terminate_rport_io or dev_loss_tmo_callbk
to be called.

The following patches attempt to unify what upper layers will see drivers
like multipath can make a good guess. This relies on drivers being
hooked into their transport class.

This first patch just defines two new host byte errors so drivers can
return the same value for when a rport/session is blocked and for
when the fast_io_fail_tmo fires.

The idea is that if the LLD/class detects a problem and is going to block
a rport/session, then if the LLD wants or must return the command to scsi-ml,
then it can return it with DID_TRANSPORT_DISRUPTED. This will requeue
the IO into the same scsi queue it came from, until the fast io fail timer
fires and the class decides what to do.

When using multipath and the fast_io_fail_tmo fires then the class
can fail commands with DID_TRANSPORT_FAILFAST or drivers can use
DID_TRANSPORT_FAILFAST in their terminate_rport_io callbacks or
the equivlent in iscsi if we ever implement more advanced recovery methods.
A LLD, like lpfc, could continue to return DID_ERROR and then it will hit
the normal failfast path, so drivers do not have fully be ported to
work better. The point of the patches is that upper layers will
not see a failure that could be recovered from while the rport/session is
blocked until fast_io_fail_tmo/recovery_timeout fires.

V3
Remove some comments.
V2
Fixed patch/diff errors and renamed DID_TRANSPORT_BLOCKED to
DID_TRANSPORT_DISRUPTED.
V1
initial patch.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The fc class now calls scsi_target_unblock after calling the
terminate callback, so this patch removes the calls from the
drivers.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

When we block a rport and the driver implements the terminate
callback we will fail IO that was running quickly. However
IO that was in the scsi_device/block queue sits there until
the dev_loss_tmo fires, and this can make it look like IO is
lost because new IO will get executed but that IO stuck in
the blocked queue sits there for some time longer.

With this patch when the fast io fail tmo fires, we will
fail the blocked IO and any new IO. This patch also allows
all drivers to partially support the fast io fail tmo. If the
terminate io callback is not implemented, we will still fail blocked
IO and any new IO, so multipath can handle that.

This patch also allows the fc and iscsi classes to implement the
same behavior. The timers are just unfornately named differently.

This patch also fixes the problem where drivers were unblocking
the target in their terminate callback, which was needed for
rport removal, but for fast io fail timeout it would cause
IO to bounce arround the scsi/block layer and the LLD queuecommand.
And it for drivers that could have IO stuck but did not have
a terminate callback the unblock calls in the class will fix
them.

v2.
- fix up bit setting style to meet JamesS's pref.
- Broke out new host byte error changes to make it easier to read.
- added JamesS's ack from list.
v1
- initial patch
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Acked-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We do want to call right back into the queuecommand during the race,
so we can just use SCSI_MLQUEUE_TARGET_BUSY.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Acked-by: NJames Smart <James.Smart@Emulex.Com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

For the conditions below we do not want the queuecommand
function to call us right back, so return SCSI_MLQUEUE_TARGET_BUSY.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

If the fcport is not online then we do not want to block IO to all ports on
the host. We just want to stop IO on port not online, so we should be using
the SCSI_MLQUEUE_TARGET_BUSY return value.

For the case where we race with the rport memset initialization
we do not want the queuecommand to be called again so we can just use
SCSI_MLQUEUE_TARGET_BUSY for this.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Acked-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

When qla4xxx begins recovery and the iscsi class is firing up to handle
it, we need to retrn SCSI_MLQUEUE_TARGET_BUSY from the driver instead
of host busy, because the session recovery only affects the one target.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Acked-by: NDavid C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

SCSI-ml manages the queueing limits for the device and host, but
does not do so at the target level. However something something similar
can come in userful when a driver is transitioning a transport object to
the the blocked state, becuase at that time we do not want to queue
io and we do not want the queuecommand to be called again.

The patch adds code similar to the exisiting SCSI_ML_*BUSY handlers.
You can now return SCSI_MLQUEUE_TARGET_BUSY when we hit
a transport level queueing issue like the hw cannot allocate some
resource at the iscsi session/connection level, or the target has temporarily
closed or shrunk the queueing window, or if we are transitioning
to the blocked state.

bnx2i, when they rework their firmware according to netdev
developers requests, will also need to be able to limit queueing at this
level. bnx2i will hook into libiscsi, but will allocate a scsi host per
netdevice/hba, so unlike pure software iscsi/iser which is allocating
a host per session, it cannot set the scsi_host->can_queue and return
SCSI_MLQUEUE_HOST_BUSY to reflect queueing limits on the transport.

The iscsi class/driver can also set a scsi_target->can_queue value which
reflects the max commands the driver/class can support. For iscsi this
reflects the number of commands we can support for each session due to
session/connection hw limits, driver limits, and to also reflect the
session/targets's queueing window.

Changes:
v1 - initial patch.
v2 - Fix scsi_run_queue handling of multiple blocked targets.
Previously we would break from the main loop if a device was added back on
the starved list. We now run over the list and check if any target is
blocked.
v3 - Rediff for scsi-misc.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Remove ending ':' from some of the Topic lines for consistency.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add F: definition since it is being used.

Expand acronyms or add them so that users of MAINTAINERS file can find
entries more easily.

Correct driver spelling.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Sorted case-insensitive (sort -f).
Groups that begin with ARM, INTEL, etc. not sorted.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix kconfig typo and extra whitespace
  ext4: fix build failure without procfs
  ext4: add an option to control error handling on file data
  jbd2: don't dirty original metadata buffer on abort
  ext4: add checks for errors from jbd2
  jbd2: fix error handling for checkpoint io
  jbd2: abort when failed to log metadata buffers

Signed-off-by: NJan Engelhardt <jengelh@medozas.de>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>

fs/ext4/super.c: In function 'ext4_fill_super':
fs/ext4/super.c:2226: error: 'ext4_ui_proc_fops' undeclared (first use
in this function)
fs/ext4/super.c:2226: error: (Each undeclared identifier is reported
only once
fs/ext4/super.c:2226: error: for each function it appears in.)
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  [CIFS] cifs: remove pointless lock and unlock of GlobalMid_Lock in header_assemble

It needs the WM97xx touchscreen driver to be compiled in, not as a
module.  And it cannot itself be a module, due to some unfortunate
interactions with platform data.
Reported-by: NHerbert Xu <herbert@gondor.apana.org.au>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge branch 'x86-core-v2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

This merges in:

  x86/build, x86/microcode, x86/spinlocks, x86/memory-corruption-check,
  x86/early-printk, x86/xsave, x86/quirks, x86/setup, x86/signal,
  core/signal, x86/urgent, x86/xen

* 'x86-core-v2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (142 commits)
  x86: make processor type select depend on CONFIG_EMBEDDED
  x86: extend processor type select help text
  x86, amd-iommu: propagate PCI device enabling error
  warnings: fix arch/x86/kernel/io_apic_64.c
  warnings: fix arch/x86/kernel/early_printk.c
  x86, fpu: check __clear_user() return value
  x86: memory corruption check - cleanup
  x86: ioperm user_regset
  xen: do not reserve 2 pages of padding between hypervisor and fixmap.
  xen: use spin_lock_nest_lock when pinning a pagetable
  x86: xsave: set FP, SSE bits in the xsave header in the user sigcontext
  x86: xsave: fix error condition in save_i387_xstate()
  x86: SB450: deprioritize DMI quirks
  x86: SB450: skip IRQ0 override if it is not routed to INT2 of IOAPIC
  x86: replace a magic number with a named constant in the VESA boot code
  x86 setup: remove IMAGE_OFFSET
  x86 setup: remove DEF_INITSEG and DEF_SETUPSEG
  Revert "x86: fix ghost EDD devices in /sys again"
  x86 setup: fix ghost entries under /sys/firmware/edd take 3
  x86: signal: remove indent in restore_sigcontext()
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  avr32: Fix build failures in board code
  avr32: Allow selecting multiple pins at once
  avr32: Minor pm_power_off cleanup
  avr32: Implement {read,write}[bwl]_be
  avr32: Replace static clock list with dynamic linked list
  avr32: Use platform_driver_probe for pdc platform driver
  avr32: Use platform_driver_probe for pio platform driver
  avr32: Provide a way to deselect pins in the portmux
  ngw100: export J15 through sysfs
  avr32: Allow fine-grained control over LCDC pins
  avr32: added mem kernel command line option support
  Add kernel support for oprofile callgraphs on AVR32
  avr32: use the new byteorder headers

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (24 commits)
  MMC: Use timeout values from CSR
  MMC: CSD and CID timeout values
  sdhci: 'scratch' may be used uninitialized
  mmc: explicitly mention SDIO support in Kconfig
  mmc: remove redundant "depends on"
  Fix comment in include/linux/mmc/host.h
  sdio: high-speed support
  mmc_block: hard code 512 byte block size
  sdhci: force high speed capability on some controllers
  mmc_block: filter out PC requests
  mmc_block: indicate strict ordering
  mmc_block: inform block layer about sector count restriction
  sdio: give sdio irq thread a host specific name
  sdio: make sleep on error interruptable
  sdhci: reduce card detection delay
  sdhci: let the controller wait for busy state to end
  atmel-mci: Add missing flush_dcache_page() in PIO transfer code
  atmel-mci: Don't overwrite error bits when NOTBUSY is set
  atmel-mci: Add experimental DMA support
  atmel-mci: support multiple mmc slots
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] orion5x_wdt.c: add spinlocking
  [WATCHDOG] Orion: add hardware watchdog support
  [WATCHDOG] omap_wdt.c: cleanup a bit omap_wdt.c
  [WATCHDOG] omap_wdt.c: another ioremap() fix
  [WATCHDOG] omap_wdt.c: sync linux-omap changes
  [WATCHDOG] Add AT91SAM9X watchdog
  [WATCHDOG] Add driver for winbond w83697ug/uf watchdog feature
  [WATCHDOG] add watchdog driver IT8716 IT8726 IT8712J/K

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: fix early panic on amd64 due to typo in supported CPU section
  x86, early_ioremap: fix fencepost error
  x86: avoid dereferencing beyond stack + THREAD_SIZE

This fixes the following compile error with CONFIG_BLOCK=n caused by
commit 68c9d702 ("generic block based
fiemap implementation"):

    CC      fs/ioctl.o
  fs/ioctl.c: In function 'generic_block_fiemap':
  fs/ioctl.c:249: error: storage size of 'tmp' isn't known
  fs/ioctl.c:272: error: invalid application of 'sizeof' to incomplete type 'struct buffer_head'
  fs/ioctl.c:280: error: implicit declaration of function 'buffer_mapped'
  fs/ioctl.c:249: warning: unused variable 'tmp'
  make[2]: *** [fs/ioctl.o] Error 1
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NJosef Bacik <jbacik@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes the following build error with CONFIG_KEYS=n, caused by
commit dfd15c46 ("cifs: explicitly
revoke SPNEGO key after session setup"):

    CC [M]  fs/cifs/sess.o
  fs/cifs/sess.c: In function 'CIFS_SessSetup':
  fs/cifs/sess.c:628: error: implicit declaration of function 'key_revoke'
  make[3]: *** [fs/cifs/sess.o] Error 1
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6: (180 commits)
  leo: disable cursor when leaving graphics mode
  cg6: disable cursor when leaving graphics mode
  sparc32: sun4m interrupt mask cleanup
  drivers/rtc/Kconfig: don't build rtc-cmos.o on sparc32
  sparc: arch/sparc/kernel/pmc.c -- extra #include?
  sparc32: Add more extensive documentation of sun4m interrupts.
  sparc32: Kill irq_rcvreg from sun4m_irq.c
  sparc32: Delete master_l10_limit.
  sparc32: Use PROM device probing for sun4c timers.
  sparc32: Use PROM device probing for sun4c interrupt register.
  sparc32: Delete claim_ticker14().
  sparc32: Stop calling claim_ticker14() from sun4c_irq.c
  sparc32: Kill clear_profile_irq btfixup entry.
  sparc32: Call sun4m_clear_profile_irq() directly from sun4m_smp.c
  sparc32: Remove #if 0'd code from sun4c_irq.c
  sparc32: Remove some SMP ifdefs in sun4d_irq.c
  sparc32: Use PROM infrastructure for probing and mapping sun4d timers.
  sparc32: Use PROM device probing for sun4m irq registers.
  sparc32: Use PROM device probing for sun4m timer registers.
  sparc: Fix user_regset 'n' field values.
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  smc911x: Fix external PHY detection
  e1000: allow VLAN devices to use TSO and CSUM offload
  gre: Initialise rtnl_link tunnel parameters properly
  ipvs: Add proper dependencies on IP_VS, and fix description header line.

Commit ed458df4 ("PnP: move
pnpacpi/pnpbios_init to after PCI init") moved the PnP RTC discovery
later, and now the ACPI RTC glue code doesn't find it any more, breaking
the RTC wakealarm sysfs interfaces, as reported by Rafael.

This really is fairly messy, and we have several annoying ordering
constraints here - the PnP code that sets up the RTC resources wants to
run after the PCI resources have to be registered, which in turn needs
to run after ACPI has at least enumerated the root PCI buses etc.  Our
initcall ordering is not fine-grained enough to make this all painless.

So this moves the ACPI RTC glue ("acpi_rtc_init()") down to a regular
module call, which fixes the problem Rafael has.  The reason this isn't
wonderful is that we really should do acpi_rtc_init before we do the
rtc_cmos init, and now those two are in the same module_init() section.

Which happens to work, but only because drivers/rtc is linked after
drivers/acpi.  In other words, we still have a very subtle ordering
issue here. Grr.
Reported-and-tested-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a few instances of board code breakage introduced by the atmel-mci
platform interface changes.
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>

at32_select_periph() now takes an u32 bitmask rather than a single pin.
This allows to set multiple pins at once.
Signed-off-by: NAlex Raimondi <mailinglist@miromico.ch>
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>

Merge branches 'x86/xen', 'x86/build', 'x86/microcode', 'x86/mm-debug-v2', 'x86/memory-corruption-check', 'x86/early-printk', 'x86/xsave', 'x86/ptrace-v2', 'x86/quirks', 'x86/setup', 'x86/spinlocks' and 'x86/signal' into x86/core-v2

deselecting one of the CPU type CONFIG_CPU_SUP_* config options
can render a kernel unbootable. Make sure this option is only
available if CONFIG_EMBEDDED is enabled.
Signed-off-by: NIngo Molnar <mingo@elte.hu>