Convert the Renesas Ethernet AVB (EthernetAVB-IF) Device Tree binding
documentation to json-schema.

Add missing properties.
Update the example to match reality.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some EtherAVB variants support internal clock delay configuration, which
can add larger delays than the delays that are typically supported by
the PHY (using an "rgmii-*id" PHY mode, and/or "[rt]xc-skew-ps"
properties).

Add properties for configuring the internal MAC delays.
These properties are mandatory, even when specified as zero, to
distinguish between old and new DTBs.

Update the (bogus) example accordingly.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NSergei Shtylyov <sergei.shtylyov@gmail.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Internal Receive and Transmit Clock Delays are a common setting for
RGMII capable devices.

While these delays are typically applied by the PHY, some MACs support
configuring internal clock delay settings, too.  Hence add standardized
properties to configure this.

This is the MAC counterpart of commit 9150069b ("dt-bindings:
net: Add tx and rx internal delays"), which applies to the PHY.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NRob Herring <robh@kernel.org>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2020-09-30

Updates and cleanups for mlx5 driver:

1) From Ariel, Dan Carpenter and Gostavo, Fixes to the previous
   mlx5 Connection track series.

2) From Yevgeny, trivial cleanups for Software steering

3) From Hamdan, Support for Flow source hint in software steering and
   E-Switch

4) From Parav and Sunil, Small and trivial E-Switch updates and
   cleanups in preparation for mlx5 Sub-functions support
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calls to kzalloc() and kvzalloc() should be null-checked
in order to avoid any potential failures. In this case,
a potential null pointer dereference.

Fix this by adding null checks for _parse_attr_ and _flow_
right after allocation.

Addresses-Coverity-ID: 1497154 ("Dereference before null check")
Fixes: c620b772 ("net/mlx5: Refactor tc flow attributes structure")
Signed-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: NLeon Romanovsky <leonro@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

This code frees "shared_counter" and then dereferences on the next line
to get the error code.

Fixes: 1edae233 ("net/mlx5e: CT: Use the same counter for both directions")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NLeon Romanovsky <leonro@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

When removing a flow from the slow path fdb, a flow attr struct is
allocated for the rule removal process. If the allocation fails the
code prints a warning message but continues with the removal flow
which include dereferencing a pointer which could be null.
Fix this by exiting the function in case the attr allocation failed.

Fixes: c620b772 ("net/mlx5: Refactor tc flow attributes structure")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAriel Levkovich <lariel@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Use the PCI device directly for dma accesses as non PCI device unlikely
support IOMMU and dma mappings.
Introduce and use helper routine to access DMA device.
Signed-off-by: NParav Pandit <parav@nvidia.com>
Reviewed-by: NVu Pham <vuhuong@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Set flow source as hint for local vport.
Signed-off-by: NHamdan Igbaria <hamdani@mellanox.com>
Reviewed-by: NOz Shlomo <ozsh@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Currently devlink eswitch ports are registered and unregistered by the
representor layer.
However it is better to register them at eswitch layer so that in future
user initiated command port add and delete commands can also
register/unregister devlink ports without depending on representor layer.
Signed-off-by: NParav Pandit <parav@nvidia.com>
Reviewed-by: NRoi Dayan <roid@nvidia.com>
Reviewed-by: NVu Pham <vuhuong@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

To register and unregister devlink ports when loading/unload
representors, refactor the code to helper functions.
Signed-off-by: NParav Pandit <parav@nvidia.com>
Reviewed-by: NRoi Dayan <roid@nvidia.com>
Reviewed-by: NVu Pham <vuhuong@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Currently only VF vports need egress ACL table.
Add a generic helper to check whether a vport need egress
ACL table or not.
Signed-off-by: NParav Pandit <parav@nvidia.com>
Reviewed-by: NRoi Dayan <roid@nvidia.com>
Reviewed-by: NVu Pham <vuhuong@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Currently only 256 vports can be supported as only 8 bits are
reserved for them and 8 bits are reserved for vhca_ids in
metadata reg c0. To support more than 256 vports, replace
vhca_id with a unique shorter 4-bit PF number which covers
upto 16 PF's. Use remaining 12 bits for vports ranging 1-4095.
This will continue to generate unique metadata even if
multiple PCI devices have same switch_id.
Signed-off-by: Nsunils <sunils@nvidia.com>
Reviewed-by: NParav Pandit <parav@nvidia.com>
Reviewed-by: NVu Pham <vuhuong@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Skip the rule according to flow arrival source, in case of RX and the
source is local port skip and in case of TX and the source is uplink
skip, we get this info according to the flow source hint we get from
upper layers when creating the rule.
This is needed because for example in case of FDB table which has a TX
and RX tables and we are inserting a rule with an encap action which
is only a TX action, in this case rule will fail on RX, so we can rely
on the flow source hint and skip RX in such case.
Until now we relied on metadata regc_0 that upper layer mapped the
port in the regc_0, but the problem is that upper layer did not always
use regc_0 for port mapping, so now we added support to flow source
hint which upper layers will pass to SW steering when creating a rule.
Signed-off-by: NAlex Vesker <valex@nvidia.com>
Signed-off-by: NHamdan Igbaria <hamdani@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Instead of getting the tag in each function, call the builder
directly with the tag. This will allow to use the same function
for building the tag and the bitmask.
Signed-off-by: NAlex Vesker <valex@nvidia.com>
Signed-off-by: NYevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

The misc3 variable is used only once and can be dropped.
Signed-off-by: NAlex Vesker <valex@nvidia.com>
Signed-off-by: NYevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

When we create a matcher we check that all fields are consumed.
There is no need for this specific check. This keeps the STE
builder functions simple and clean.
Signed-off-by: NAlex Vesker <valex@nvidia.com>
Signed-off-by: NYevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Mask validity for ste builders is checked by mlx5dr_ste_build_pre_check
during matcher creation.
It already checks the mask value of source_vport, so removing
this duplicated check.
Also, moving there the check of source_eswitch_owner_vhca_id mask.
Signed-off-by: NAlex Vesker <valex@nvidia.com>
Signed-off-by: NYevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Validity check is done by reading the next lu_type from the STE,
this check can be replaced by checking the refcount.
This will make the check independent on internal STE structure.
Signed-off-by: NAlex Vesker <valex@nvidia.com>
Signed-off-by: NYevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Ido Schimmel says:

====================
drop_monitor: Convert to use devlink tracepoint

Drop monitor is able to monitor both software and hardware originated
drops. Software drops are monitored by having drop monitor register its
probe on the 'kfree_skb' tracepoint. Hardware originated drops are
monitored by having devlink call into drop monitor whenever it receives
a dropped packet from the underlying hardware.

This patch set converts drop monitor to monitor both software and
hardware originated drops in the same way - by registering its probe on
the relevant tracepoint.

In addition to drop monitor being more consistent, it is now also
possible to build drop monitor as module instead of as a builtin and
still monitor hardware originated drops. Initially, CONFIG_NET_DEVLINK
implied CONFIG_NET_DROP_MONITOR, but after commit def2fbff
("kconfig: allow symbols implied by y to become m") we can have
CONFIG_NET_DEVLINK=y and CONFIG_NET_DROP_MONITOR=m and hardware
originated drops will not be monitored.

Patch set overview:

Patch #1 adds a tracepoint in devlink for trap reports.

Patch #2 prepares probe functions in drop monitor for the new
tracepoint.

Patch #3 converts drop monitor to use the new tracepoint.

Patches #4-#6 perform cleanups after the conversion.

Patch #7 adds a test case for drop monitor. Both software originated
drops and hardware originated drops (using netdevsim) are tested.

Tested:

| CONFIG_NET_DEVLINK | CONFIG_NET_DROP_MONITOR | Build | SW drops | HW drops |
| -------------------|-------------------------|-------|----------|----------|
|          y         |            y            |   v   |     v    |     v    |
|          y         |            m            |   v   |     v    |     v    |
|          y         |            n            |   v   |     x    |     x    |
|          n         |            y            |   v   |     v    |     x    |
|          n         |            m            |   v   |     v    |     x    |
|          n         |            n            |   v   |     x    |     x    |
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test that drop monitor correctly captures both software and hardware
originated packet drops.

# ./drop_monitor_tests.sh

Software drops test
    TEST: Capturing active software drops                               [ OK ]
    TEST: Capturing inactive software drops                             [ OK ]

Hardware drops test
    TEST: Capturing active hardware drops                               [ OK ]
    TEST: Capturing inactive hardware drops                             [ OK ]

Tests passed:   4
Tests failed:   0
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, devlink called into drop monitor in order to report hardware
originated drops / exceptions. devlink intentionally filtered control
packets and did not pass them to drop monitor as they were not dropped
by the underlying hardware.

Now drop monitor registers its probe on a generic 'devlink_trap_report'
tracepoint and should therefore perform this filtering itself instead of
having devlink do that.

Add the trap type as metadata and have drop monitor ignore control
packets.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'struct net_dm_hw_metadata' is a duplicate of 'struct
devlink_trap_metadata'.

Remove the former and simplify the code.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The old probe functions that were invoked by drop monitor code are no
longer called and can thus be removed. They were replaced by actual
probe functions that are registered on the recently introduced
'devlink_trap_report' tracepoint.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert drop monitor to use the recently introduced
'devlink_trap_report' tracepoint instead of having devlink call into
drop monitor.

This is both consistent with software originated drops ('kfree_skb'
tracepoint) and also allows drop monitor to be built as a module and
still report hardware originated drops.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drop monitor supports two alerting modes: Summary and packet. Prepare a
probe function for each, so that they could be later registered on the
devlink tracepoint by calling register_trace_devlink_trap_report(),
based on the configured alerting mode.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a tracepoint for trap reports so that drop monitor could register
its probe on it. Use trace_devlink_trap_report_enabled() to avoid
wasting cycles setting the trap metadata if the tracepoint is not
enabled.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-5.10-20200930' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2020-09-30

this is a pull request of 13 patches for net-next.

The first 10 target the mcp25xxfd driver (which is renamed to mcp251xfd during
this series).

The first two patches are by Thomas Kopp, which adds reference to the just
related errata and updates the documentation and log messages.

Dan Carpenter's patch fixes a resource leak during ifdown.

A patch by me adds the missing initialization of a variable.

Oleksij Rempel updates the DT binding documentation as requested by Rob
Herring.

The next 5 patches are by Thomas Kopp and me. During review Geert Uytterhoeven
suggested to use "microchip,mcp251xfd" instead of "microchip,mcp25xxfd" as the
DT autodetection compatible to avoid clashes with future but incompatible
devices. We decided not only to rename the compatible but the whole driver from
"mcp25xxfd" to "mcp251xfd". This is done in several patches.

Joakim Zhang contributes three patches for the flexcan driver. The first one
adds support for the ECC feature, which is implemented on some modern IP cores,
by initializing the controller's memory during ifup. The next patch adds
support for the i.MX8MP (which supports ECC) and the last patch properly
disables the runtime PM if device registration fails.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic watchdog training

Our link watchdog displayed a couple of unfriendly behaviors in some recent
stress testing.  These patches change the startup and stop timing in order
to be sure that expected structures are ready to be used by the watchdog.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In one corner case scenario, the driver device lif setup can
get delayed such that the ionic_watchdog_cb() timer goes off
before the ionic->lif is set, thus causing a NULL pointer panic.
We catch the problem by checking for a NULL lif just a little
earlier in the callback.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to be better at making sure we don't have a link check
watchdog go off while we're shutting things down, so let's stop
the timer as soon as we start the remove.

Meanwhile, since that was the only thing in
ionic_dev_teardown(), simplify and remove that function.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
tcp: exponential backoff in tcp_send_ack()

We had outages caused by repeated skb allocation failures in tcp_send_ack()

It is time to add exponential backoff to reduce number of attempts.
Before doing so, first patch removes icsk_ack.blocked to make
room for a new field (icsk_ack.retry)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Whenever host is under very high memory pressure,
__tcp_send_ack() skb allocation fails, and we setup
a 200 ms (TCP_DELACK_MAX) timer before retrying.

On hosts with high number of TCP sockets, we can spend
considerable amount of cpu cycles in these attempts,
add high pressure on various spinlocks in mm-layer,
ultimately blocking threads attempting to free space
from making any progress.

This patch adds standard exponential backoff to avoid
adding fuel to the fire.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NSoheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TCP has been using it to work around the possibility of tcp_delack_timer()
finding the socket owned by user.

After commit 6f458dfb ("tcp: improve latencies of timer triggered events")
we added TCP_DELACK_TIMER_DEFERRED atomic bit for more immediate recovery,
so we can get rid of icsk_ack.blocked

This frees space that following patch will reuse.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NSoheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct macb_platform_data is only used by macb_pci to register the platform
device, move its definition to cadence/macb.h and remove platform_data/macb.h
Signed-off-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Petr Machata says:

====================
mlxsw: PFC and headroom selftests

Recent changes in the headroom management code made it clear that an
automated way of testing this functionality is needed. This patchset brings
two tests: a synthetic headroom behavior test, which verifies mechanics of
headroom management. And a PFC test, which verifies whether this behavior
actually translates into a working lossless configuration.

Both of these tests rely on mlnx_qos[1], a tool that interfaces with Linux
DCB API. The tool was originally written to work with Mellanox NICs, but
does not actually rely on anything Mellanox-specific, and can be used for
mlxsw as well as for any other NIC-like driver. Unlike Open LLDP it does
support buffer commands and permits a fire-and-forget approach to
configuration, which makes it very handy for writing of selftests.

Patches #1-#3 extend the selftest devlink_lib.sh in various ways. Patch #4
then adds a helper wrapper for mlnx_qos to mlxsw's qos_lib.sh.

Patch #5 adds a test for management of port headroom.

Patch #6 adds a PFC test.

[1] https://github.com/Mellanox/mlnx-tools/
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a test for PFC. Runs 10MB of traffic through a bottleneck and checks
that none of it gets lost.
Signed-off-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a test for headroom configuration. This covers projection of ETS
configuration to ingress, PFC, adjustments for MTU, the qdisc / TC
mode and the effect of egress SPAN session on buffer configuration.
Signed-off-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlnx_qos is a script for configuration of DCB. Despite the name it is not
actually Mellanox-specific in any way. It is currently the only ad-hoc tool
available (in contrast to a daemon that manages an interface on an ongoing
basis). However, it is very verbose and parsing out error messages is not
really possible. Add a wrapper that makes it easier to use the tool.
Signed-off-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some selftests may not need any actual ports. Technically those are not
forwarding selftests, but devlink_lib can still be handy. Fall back on
NETIF_NO_CABLE in those cases.
Signed-off-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>