Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The chainmasks were already configured at process_ini
before doing init calibration.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Once RXEOL was disabled, it never be enabled again. This patch
re-enables rxeol at the end of rx tasklet.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whenever RXEOL is received, both RXORN and RXEOL got cleared
to avoid rx overrun interrupt storm. This was handled only for
edma chips. The same scenario was also observered with AR9280,
doing frequent channel type switch b/w HT20/40 with bidi traffic
that is causing failure to stop rx dma. This patch clears
the RXEOL & RXORN interrupts for all chips.

ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020
DMADBG_7=0x000062c0
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:532
ath_stoprecv+0x110/0x120 [ath9k]()
Call Trace:
 [<ffffffff8104a55a>] warn_slowpath_common+0x7a/0xb0
 [<ffffffff8104a5a5>] warn_slowpath_null+0x15/0x20
 [<ffffffffa0560380>] ath_stoprecv+0x110/0x120 [ath9k]
 [<ffffffffa055e6fa>] ath_reset+0x6a/0x200 [ath9k]
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The WAR which adds extra delimiters when using RTS/CTS
with aggregation and non-enterprise AR9003 chips.
This extra padding is done after doing all the 4ms limit
checks and hence the total aggregate sizes are exceeding
the allowed duration. This patch limits the aggregate
sizes appropriately after including these extra delimiters.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow userspace to set NL80211_MESHCONF_GATE_ANNOUNCEMENTS attribute,
which will advertise this mesh node as being a mesh gate.
NL80211_HWMP_ROOTMODE must be set or this will do nothing.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow userspace to set Root Announcement Interval for our mesh
interface. Also, RANN interval is now in proper units of TUs.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fix allows userspace to mark a meshif as a root node.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In this implementation, a mesh gate is a root node with a certain bit
set in its RANN flags. The mpath to this root node is marked as a path
to a gate, and added to our list of known gates for this if_mesh. Once a
path discovery process fails, we forward the unresolved frames to a
known gate. Thanks to Luis Rodriguez for refactoring and bug fix help.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously, mpaths were never flushed since the mpath is not active once
we call this function.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mesh_queue_preq is invoked invoked from both user (work queue) and
softirq (timer) context, so the _bh version of spinlock needs to be
used. Also, the mpath->state_lock should be softirq safe as well.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If we have an mpath whose timer has not been initialized, don't try to
delete it.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

make hwmp_dbg print the relevant sdata->name by default and improve
formatting. Also add mpath_dbg macro for debugging of mesh path
operations.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sometimes we need to write table which is 2-10 elements long. It's
easier to create such a function instead of defining array every time.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No need to recompile the module anymore to set the debug level.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

MMIO hacks were used to trick ndis&wl. For example following:
 phy_read(0x0280) -> 0xffff
phy_write(0x0280) <- 0xff3e
***
 phy_read(0x0280) -> 0x0000
phy_write(0x0280) <- 0x003e
was translated to mask 0xff00 and set 0x3e.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a client disassociates from a crypto enabled bss, data traffic to
other clients connected to the bss is stalled. This was due to a boolean
variable used to keep track if HW crypto is enabled i.e. if set key has
been called to add a key.  This flag was being reset every time delete
key was called e.g when a station leaves the bss. Once the flag is
reset, rx status flags were not being set for connected clients which
disrupts traffic to these clients. Fix this issue by not resetting the
flag since we do not need to reset this flag during the life time of the
bss.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make mesh path selection frames Mesh Action category, remove outdated
Mesh Path Selection category and defines, use updated reason codes, add
mesh_action_is_path_sel for readability, and update/correct path
selection IEs.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch updates the mesh peering frames to the format specified in
the recently ratified 802.11s standard. Several changes took place to
make this happen:

	- Change RX path to handle new self-protected frames
	- Add new Peering management IE
	- Remove old Peer Link IE
	- Remove old plink_action field in ieee80211_mgmt header

These changes by themselves would either break peering, or work by
coincidence, so squash them all into this patch.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Have the mesh peering frames use the self-protected action and reason codes
specified in 802.11s and defined in ieee80211.h. Remove the local enums.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

802.11s introduces a new action frame category, add action codes as well
as an entry in ieee80211_mgmt.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Correct ordering of IEs in the mesh beacon while removing unneeded IEs
from mesh peering frames. Set privacy bit in capability info if security
is enabled. Add utility functions to aid in construction
of IEs and reduce code duplication.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We need to disable ext. PA lines for reading SPROM. It's disabled by
default, but this patch allows using bcma after loading wl, which leaves
workaround enabled.

Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replace "old" and "new" with number of the first firmware known to use
the given format.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As described at [1] some STAs (i.e. Intel 5100 Windows) can end up
correctly BlockAcking incoming frames without delivering them to user
space if a AMPDU subframe got lost and we don't flush the receipients
reorder buffer with a BlockAckReq. This in turn results in stuck
connections.

According to 802.11n-2009 it is not necessary to send a BAR to flush
the recepients RX reorder buffer but we still do that to be polite.

However, assume the following frame exchange:

AP -> STA, AMPDU (failed)
AP -> STA, BAR (failed)

The client in question then ends up in the same situation and won't
deliver frames to userspace anymore since we weren't able to flush
its reorder buffer.

This is not a hypothetical situation but I was able to observe this
exact behavior during a stress test between a rt2800pci AP and a Intel
5100 Windows client.

In order to work around this issue just tear down the BA session as
soon as a BAR failed to be TX'ed.

[1] http://comments.gmane.org/gmane.linux.kernel.wireless.general/66867Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While at it also fix the indention of the other IEEE80211_BAR_CTRL_ defines.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>