Clean up the locking by splitting it into two functions,
this will also enable further cleanups of stopping all
sessions.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The sta_info pointer can very well be passed to
ieee80211_sta_tear_down_BA_sessions, this will
later allow us to pass it through even further.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As far as I can tell, there are possible lockups because both the RX
session_timer and TX addba_resp_timer are del_timer_sync'ed under
the sta spinlock which both timer functions take. Additionally, the
TX agg code seems to leak memory when TX aggregation is not disabled
before the sta_info is freed.

Fix this by making the free code a little smarter in the RX agg case,
and actually make the sta_info_destroy code free the TX agg info in
the TX agg case. We won't notify the peer, but it'll notice something
is wrong anyway, and normally this only happens after we've told it
in some other way we will no longer talk to it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When disabling TX aggregation because it was rejected or from
the timer (it was not accepted), there is a window where we
first set the state to operation, unlock, and then undo the
whole thing. Avoid that by splitting up the stop function.
Also get rid of the pointless sta_info indirection in the timer.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add documentation and move ieee80211_start_tx_ba_cb_irqsafe to right
after ieee80211_start_tx_ba_cb.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Doing so would be an MLME protocol violation when the peer disabled
the aggregation session. Quick driver review indicates that there are
error codes passed all over the drivers but cannot ever be nonzero
except in error conditions that would indicate mac80211 bugs.

No real changes here, since no drivers currently can return -EBUSY.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can only support aggregation on AP/STA right now. HT isn't defined
for IBSS, WDS or MESH. In the WDS/MESH cases it's not clear what to
put into the IBSS field, and we don't handle that in the code at all.
Also fix the code to handle VLAN correctly.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Create two new files, agg-tx.c and agg-rx.c to make it clearer
which code is common (ht.c) and which is specific (agg-*.c).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The values are in TUs (1.024ms), not ms.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's a little confusing to get the BSSID outside the function
and pass it in, when it's only needed for this function, so
change that.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hopefully the last required fix ... disable beaconing
only on beaconing interfaces, and thus avoid calling
ieee80211_if_config for purely virtual interfaces
(those driver doesn't know about).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We cannot currently hand off extra IEs to hw_scan, so reject
configuring extra IEs for probe request frames when hw_scan
is set.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make sure nobody passes in bogus values, and translate the values
(although it isn't necessary).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes zd1211rw honour enable_beacon, as well as fixing
a memory leak: the beacon skb is leaked when configuring it
to the hardware fails.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Before we have a probe response frame (which is used as the
beacon too) there's no need to ask drivers to beacon, they
will not get a beacon anyway.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is rather confusing to see this in the log:
[  695.606877] __ratelimit: 40 callbacks suppressed
[  700.726878] __ratelimit: 40 callbacks suppressed

without ever seeing any actual message. This is because
zd1211rw doesn't compile out the net_ratelimit() call
properly if debugging is not enabled.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a directed tim bit is set, mac80211 currently disables power save
ands sends a null frame to the AP. But if dynamic power save is
disabled, mac80211 will not enable power save ever gain. Fix this by
adding ps-poll functionality to mac80211. When a directed tim bit is
set, mac80211 sends a ps-poll frame to the AP and checks for the more
data bit in the returned data frames.

Using ps-poll is slower than waking up with null frame, but it's saves more
power in cases where the traffic is low. Userspace can control if either
ps-poll or null wakeup method is used by enabling and disabling dynamic
power save.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently mac80211 checks for the multicast tim bit from beacons,
disables power save and sends a null frame if the bit is set. This was
added to support ath9k. But this is a bit controversial because the AP will
send multicast frames immediately after the beacon and the time constraints
are really high. Relying mac80211 to be fast enough here might not be
reliable in all situations. And there's no need to send a null frame, AP
will send the frames immediately after the dtim beacon no matter what.

Also if dynamic power save is disabled (iwconfig wlan0 power timeout 0)
currently mac80211 disables power save whenever the multicast bit is set
but it's never enabled again after receiving the first multicast/broadcast
frame.

The current implementation is not usable on p54/stlc45xx and the
easiest way to fix this is to remove the multicast tim bit check
altogether. Handling multicast tim bit in host is rare, most of the
designs do this in firmware/hardware, so it's better not to have it in
mac80211. It's a lot better to do this in firmware/hardware, or if
that's not possible it could be done in the driver.

Also renamed the function to ieee80211_check_tim() to follow the style
of the file.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes the various function pointer
assignments and unifies them in a single ops structure.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is preparatory work for removing the individual
function pointer assignments in eeprom.c
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Finally, merge these structures and have a single
HW specific data structure.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A few variables (bssid, bssidmask, curaid) were duplicated in
struct ath_softc and in ath_hal, remove them.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves all the HW version/revision specific
information into a separate structure.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes the useless sc_ prefixes for all variables.
Also, refer to interfaces as VIFs and not as VAPs anymore.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch converts the ANI channel reference to a pointer,
this facilitates moving struct ar5416AniState to ani.h
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Split the core header files into manageable pieces.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * We call reset too often and this can result various PHY problems.
  On config_interface we don't need to reset the whole device.

  TODO: Create a function hw_fast_reset that only resets the PCU
  (tx/rx stuff) and not the whole device so that we can use this for
  stuck beacons etc.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Don't enable BMISS interrupts as we don't handle them yet
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Update reset and sync with HALs

 * Clean up eeprom settings and tweaking of initvals and
   put them on separate functions

 * Set/Restore 32KHz ref clk operation

 * Add some more documentation

 TODO: Spur mitigation, tpc, half/quarter rate, compression etc

 v2: Address comments from Bob and Felix and fix RSSI threshold bug
 introduced on the first version of the patch
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Update initvals to match legacy and Sam's HAL
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Use the new way to modify rf buffer and put some rf buffer
   documentation on rfbufer.h

 * Merge all rf regs functions to one

 * Sync with legacy HAL and Sam's HAL

 * Set gain_F settings so that gain_F optimization engine works
   on RF5111/RF5112 (note that both HALs only use step 0 for RF5111
   and they don't use gain_F optimization for this chip, code is
   there but is never used)
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Update and cleanup rf gain optimization code

 * Add comments and refferences to docs and use sane function names

 * Use only step index on ath5k_gain, no need to have a pointer to
   the current step since we can determine te step from it's index,
   this also allows us to put all other structs on rfgain.h and cleanup
   ath5k.h a little

 * No need for ah_rfgain variable, we use ah_gain.g_state for everything

 * Tested on RF2112B chip but gain_F calibration is not yet done
   (we will finish this on the next patch where we'll rewrite rf-buffer
   handling)

 * Use initial rf gain settings for 2316 and 2317 SoCs introduced on a previous patch

 It seems big but it's mostly cleanup, very few functional changes have been made on phy.c
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Clean up initial rf buffer settings (new file rfbufer.h) and introduce a
   new way to access specific rf registers (will use it later)

 * Clean up initial rf gain settings by moving them on a new file (rfgain.h)
   so we can later work on gain optimization functions

 * Update initial rf buffer settings and initial rf gain settings from HALs.
   This breaks things for now because our current dumps come from pre-configured
   rf buffer (regdumps already had the needed values set from binary HAL).
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The atomic requirement for the TSF callbacks
is outdated. get_tsf() is only called by
ieee80211_rx_bss_info() which is indirectly
called by the work queue ieee80211_sta_work().
In the same context are called several other
non-atomic functions, too.
And the atomic requirement causes problems
for drivers of USB wifi cards.
Signed-off-by: NAlina Friedrichsen <x-alina@gmx.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This issue happens only when we are associated with a 11n AP and power save
is enabled. In the function 'ieee80211_master_start_xmit', ps_disable_work
is queued where wake_queues is called. But before this work is executed,
we check if the queues are stopped in _ieee80211_tx and return TX_AGAIN to
ieee8011_tx which leads to the warning message.
This patch fixes this erroneous case.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>