Newer firmware has a new call HWRM_FUNC_QSTATS_EXT to retrieve the
masks of all ring counters.  Make this call when supported to
initialize the hardware masks of all ring counters.  If the call
is not available, assume 48-bit ring counter masks on P5 chips.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of these DMAed hardware counters are not full 64-bit counters and
so we need to accumulate them as they overflow.  Allocate copies of these
DMA statistics memory blocks with the same size for accumulation.  The
hardware counter widths are also counter specific so we allocate
memory for masks that correspond to each counter.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver manages multiple statistics structures of different sizes.
They are all allocated, freed, and handled practically the same.  Define
a new bnxt_stats_mem structure and common allocation and free functions
for all staistics memory blocks.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The port statistics structures have hard coded padding and offset.
Define macros to make this look cleaner.
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Main changes are 200G support and fixing the definitions of discard and
error counters to match the hardware definitions.

Because the HWRM_PORT_PHY_QCFG message size has now exceeded the max.
encapsulated response message size of 96 bytes from the PF to the VF,
we now need to cap this message to 96 bytes for forwarding.  The forwarded
response only needs to contain the basic link status and speed information
and can be capped without adding the new information.

v2: Fix bnxt_re compile error.

Cc: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove PCIe non-counters display from ethtool statistics, as
they are not simple counters but register dump.  The next few
patches will add logic to detect counter roll-over and it won't
work with these PCIe non-counters.

There will be a follow up patch to get PCIe information via
ethtool register dump.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the ism driver allocates a new dmb in ism_alloc_dmb() it must
first check for and reserve a slot in the sba bitmap. When
find_next_zero_bit() finds no free slot then the return code is -ENOMEM.
This code conflicts with the error when the alloc() fails later in the
code. As a result of that the caller can not differentiate
between out-of-memory conditions and sba-bitmap-full conditions.
Fix that by using the return code -ENOSPC when the sba slot
reservation failed.
Reviewed-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

list_for_each_safe is able to handle an empty list.
The only effect of avoiding the loop is not initializing the
index variable.
Drop list_empty tests in cases where these variables are not
used.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

<smpl>
@@
expression x,e;
iterator name list_for_each_safe;
statement S;
identifier i,j;
@@

-if (!(list_empty(x))) {
   list_for_each_safe(i,j,x) S
- }
 ... when != i
     when != j
(
  i = e;
|
? j = e;
)
</smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@inria.fr>
Acked-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixed 2 issues with the usage of skb_cow in LAPB drivers
"lapbether" and "hdlc_x25":

1) After skb_cow fails, kfree_skb should be called to drop a reference
to the skb. But in both drivers, kfree_skb is not called.

2) skb_cow should be called before skb_push so that is can ensure the
safety of skb_push. But in "lapbether", it is incorrectly called after
skb_push.

More details about these 2 issues:

1) The behavior of calling kfree_skb on failure is also the behavior of
netif_rx, which is called by this function with "return netif_rx(skb);".
So this function should follow this behavior, too.

2) In "lapbether", skb_cow is called after skb_push. This results in 2
logical issues:
   a) skb_push is not protected by skb_cow;
   b) An extra headroom of 1 byte is ensured after skb_push. This extra
      headroom has no use in this function. It also has no use in the
      upper-layer function that this function passes the skb to
      (x25_lapb_receive_frame in net/x25/x25_dev.c).
So logically skb_cow should instead be called before skb_push.

Cc: Eric Dumazet <edumazet@google.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: NXie He <xie.he.0141@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the chips in the mv88e6xxx family don't support jumbo
configuration per port. But they do have a chip-wide max frame size that
can be used. Use this to approximate the behaviour of configuring a port
based MTU.
Signed-off-by: NChris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MV88E6190 and MV88E6190X both support per port jumbo configuration
just like the other GE switches. Install the appropriate ops.
Signed-off-by: NChris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MV88E6097 chip does not support configuring jumbo frames. Prior to
commit 5f436666 only the 6352, 6351, 6165 and 6320 chips configured
jumbo mode. The refactor accidentally added the function for the 6097.
Remove the erroneous function pointer assignment.

Fixes: 5f436666 ("net: dsa: mv88e6xxx: Refactor setting of jumbo frames")
Signed-off-by: NChris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove casting the values returned by memory allocation function.

Coccinelle emits WARNING:

./drivers/net/ethernet/hisilicon/hix5hd2_gmac.c:1027:9-23: WARNING:
 casting value returned by memory allocation function to (struct sg_desc *) is useless.

This issue was detected by using the Coccinelle software.
Signed-off-by: NWang Hai <wanghai38@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a potential race in xennet_remove(); this is what the driver is
doing upon unregistering a network device:

  1. state = read bus state
  2. if state is not "Closed":
  3.    request to set state to "Closing"
  4.    wait for state to be set to "Closing"
  5.    request to set state to "Closed"
  6.    wait for state to be set to "Closed"

If the state changes to "Closed" immediately after step 1 we are stuck
forever in step 4, because the state will never go back from "Closed" to
"Closing".

Make sure to check also for state == "Closed" in step 4 to prevent the
deadlock.

Also add a 5 sec timeout any time we wait for the bus state to change,
to avoid getting stuck forever in wait_event().
Signed-off-by: NAndrea Righi <andrea.righi@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/isdn/mISDN/socket.c: In function ‘data_sock_setsockopt’:
./include/linux/kern_levels.h:5:18: warning: format ‘%p’ expects argument of type ‘void *’, but argument 6 has type ‘sockptr_t’ [-Wformat=]
    5 | #define KERN_SOH "\001"  /* ASCII Start Of Header */
      |                  ^~~~~~
./include/linux/kern_levels.h:15:20: note: in expansion of macro ‘KERN_SOH’
   15 | #define KERN_DEBUG KERN_SOH "7" /* debug-level messages */
      |                    ^~~~~~~~
drivers/isdn/mISDN/socket.c:410:10: note: in expansion of macro ‘KERN_DEBUG’
  410 |   printk(KERN_DEBUG "%s(%p, %d, %x, %p, %d)\n", __func__, sock,
      |          ^~~~~~~~~~
drivers/isdn/mISDN/socket.c:410:38: note: format string is defined here
  410 |   printk(KERN_DEBUG "%s(%p, %d, %x, %p, %d)\n", __func__, sock,
      |                                     ~^
      |                                      |
      |                                      void *
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rework the remaining setsockopt code to pass a sockptr_t instead of a
plain user pointer.  This removes the last remaining set_fs(KERNEL_DS)
outside of architecture specific code.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> [ieee802154]
Acked-by: NMatthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An imbalanced TX indirection table causes netvsc to have low
performance. This table is created and managed during runtime. To help
better diagnose performance issues caused by imbalanced tables, it needs
make TX indirection tables visible.

Because TX indirection table is driver specified information, so
display it via ethtool register dump.
Signed-off-by: NChi Song <chisong@microsoft.com>
Reviewed-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Randy reported compile failure when CONFIG_SYSCTL is not set/enabled:

ERROR: modpost: "sysctl_vals" [drivers/net/vrf.ko] undefined!

Fix by splitting out the sysctl init and cleanup into helpers that
can be set to do nothing when CONFIG_SYSCTL is disabled. In addition,
move vrf_strict_mode and vrf_strict_mode_change to above
vrf_shared_table_handler (code move only) and wrap all of it
in the ifdef CONFIG_SYSCTL.

Update the strict mode tests to check for the existence of the
/proc/sys entry.

Fixes: 33306f1a ("vrf: add sysctl parameter for strict mode")
Cc: Andrea Mayer <andrea.mayer@uniroma2.it>
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NDavid Ahern <dsahern@kernel.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There isn't a case for 1G SGMII in ice_get_media_type() so add
the handling for it.

Also handle the special case where some direct attach
cables may report that they support 1G SGMII, but
that is erroneous since SGMII is supposed to be a
backplane media type (between a MAC and a PHY). If
the driver doesn't handle this special case then a
user could see the 'Port' in ethtool change from
'Direct attach Copper' to 'Backplane' when they have
forced the speed to 1G, but the cable hasn't changed.

Lastly, change ice_aq_get_phy_caps() to save the
module_type info if the function was called with
ICE_AQC_REPORT_TOPO_CAP. This call uses the media
information to populate the module_type. If no
media is present then the values in module_type
will be 0.
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Report AOC types as fiber instead of unknown.
Signed-off-by: NDoug Dziggel <douglas.a.dziggel@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Add AQC get link topology handle support. This is needed to determine
Direct Attach (DA) or backplane media type for PHY types that support
either. Get link topology handle cage node type request can be used to
determine if a cage is present or not. If a cage is present for PHY
types that supports both DA and backplane media type, then the media
type is DA, else the media type is backplane.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Rename the low_power_ctrl field to low_power_ctrl_an to be properly
descriptive of it being an autoneg field.
Signed-off-by: NLev Faerman <lev.faerman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Firmware now reports AN28, AN32, and AN73. Add a helper and check these new
values and report PHY autoneg capability.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Add debug logs for ice_aq_get_phy_caps(), and format
ice_aq_set_phy_cfg() and ice_aq_get_link_info() debug logs to make them
more readable.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

When the Port Disable bit is set in the Link Default Override Mask TLV PFA
module in the NVM, Total Port Shutdown mode is supported and enabled.  In
this mode, the driver should act as if the link-down-on-close ethtool
private flag is always enabled and dis-allow any change to that flag.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Adds functions to check for link override firmware support and get
the override settings for a port. The previously supported/default link
mode was strict mode.

In strict mode link is configured based on get PHY capabilities PHY types
with media.

Lenient mode is now the default link mode. In lenient mode the link is
configured based on get PHY capabilities PHY types without media. This
allows the user to configure link that the media does not report. Limit the
minimum supported link mode to 25G for devices that support 100G, and 1G
for devices that support less than 100G.

Default override is only supported in lenient mode. If default override
is supported and enabled, then default override values are used for
configuring speed and FEC. Default override provide persistent link
settings in the NVM.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: NEvan Swanson <evan.swanson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

geneve_nl2info() sets 'df' conditionally, so we have to
initialize it by copying the value from existing geneve
device in geneve_changelink().

Fixes: 56c09de3 ("geneve: allow changing DF behavior after creation")
Reported-by: syzbot+7ebc2e088af5e4c0c9fa@syzkaller.appspotmail.com
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: NSabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Very similar to commit 544f287b
("bonding: check error value of register_netdevice() immediately"),
we should immediately check the return value of register_netdevice()
before doing anything else.

Fixes: 005db31d ("bonding: set carrier off for devices created through netlink")
Reported-and-tested-by: syzbot+bbc3a11c4da63c1b74d6@syzkaller.appspotmail.com
Cc: Beniamino Galvani <bgalvani@redhat.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the transition from no media to media FW will clear the
set-phy-cfg data set by the user. Save initial PHY settings and any
settings later requested by the user and use that data to restore PHY
settings on media insertion. Since PHY configuration is now being stored,
replace calls that were calling FW to get the configuration with the saved
copy.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: NChinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The call to ice_cfg_phy_fec() requires the caller to perform certain
actions before calling it. Instead of imposing these preconditions move
the operations into the function and perform them ourselves.

Also, fix some style issues in nearby touched code.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: NChinh T Cao <chinh.t.cao@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Create a helper function for configuring requested flow control so that it
can be utilized by other functions looking to configure flow control
settings. Utilize the existing helper ice_copy_phy_caps_to_cfg() to copy a
PHY capability to configuration instead duplicating the code for it.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Add callbacks needed to support advanced power management for Wake on LAN.
Also make ice_pf_state_is_nominal function available for all configurations
not just CONFIG_PCI_IOV.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Using the new ice_aq_list_caps and ice_parse_(dev|func)_caps functions,
replace ice_discover_caps with two functions that each take a pointer to
the dev_caps and func_caps structures respectively.

This makes the side effect of updating the hw->dev_caps and
hw->func_caps obvious from reading the implementation of the function.
Additionally, it opens the way for enabling reading of device
capabilities outside of the initialization flow. By passing in
a pointer, another caller will be able to read the capabilities without
modifying the HW capabilities structures.

As there are no other callers, it is safe to now remove
ice_aq_discover_caps and ice_parse_caps.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The ice_parse_caps function is used to convert the capability block data
coming from firmware into a structured format used by other parts of the
code.

The current implementation directly updates the hw->func_caps and
hw->dev_caps structures. It is directly called from within
ice_aq_discover_caps. This causes the discover_caps function to have the
side effect of modifying the HW capability structures, which is not
intuitive.

Split this function into ice_parse_dev_caps and ice_parse_func_caps.
These functions will take a pointer to the dev_caps and func_caps
respectively. Also create an ice_parse_common_caps for sharing the
capability logic that is common to device and function.

Doing so enables a future refactor to allow reading and parsing
capabilities into a local caps structure instead of modifying the
members of the HW structure directly.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The ice_discover_caps function is used to read the device and function
capabilities, updating the hardware capabilities structures with
relevant data.

The exact number of capabilities returned by the hardware is unknown
ahead of time. The AdminQ command will report the total number of
capabilities in the return buffer.

The current implementation involves requesting capabilities once,
reading this returned size, and then re-requested with that size.

This isn't really necessary. The firmware interface has a maximum size
of ICE_AQ_MAX_BUF_LEN. Firmware can never return more than
ICE_AQ_MAX_BUF_LEN / sizeof(struct ice_aqc_list_caps_elem) capabilities.

Avoid the retry loop by simply allocating a buffer of size
ICE_AQ_MAX_BUF_LEN. This is significantly simpler than retrying. The
extra allocation isn't a big deal, as it will be released after we
finish parsing the capabilities.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

When I have KASAN enabled on my kernel and I start stressing the
touchscreen my system tends to hang.  The touchscreen is one of the
only things that does a lot of big i2c transfers and ends up hitting
the DMA paths in the geni i2c driver.  It appears that KASAN adds
enough delay in my system to tickle a race condition in the DMA setup
code.

When the system hangs, I found that it was running the geni_i2c_irq()
over and over again.  It had these:

m_stat   = 0x04000080
rx_st    = 0x30000011
dm_tx_st = 0x00000000
dm_rx_st = 0x00000000
dma      = 0x00000001

Notably we're in DMA mode but are getting M_RX_IRQ_EN and
M_RX_FIFO_WATERMARK_EN over and over again.

Putting some traces in geni_i2c_rx_one_msg() showed that when we
failed we were getting to the start of geni_i2c_rx_one_msg() but were
never executing geni_se_rx_dma_prep().

I believe that the problem here is that we are starting the geni
command before we run geni_se_rx_dma_prep().  If a transfer makes it
far enough before we do that then we get into the state I have
observed.  Let's change the order, which seems to work fine.

Although problems were seen on the RX path, code inspection suggests
that the TX should be changed too.  Change it as well.

Fixes: 37692de5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Tested-by: NSai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: NAkash Asthana <akashast@codeaurora.org>
Reviewed-by: NStephen Boyd <swboyd@chromium.org>
Reviewed-by: NMukesh Kumar Savaliya <msavaliy@codeaurora.org>
Signed-off-by: NWolfram Sang <wsa@kernel.org>

On R-Car Gen2, we get a timeout when reading from the address set in
ICSAR, even though the slave interface is disabled. Clearing it fixes
this situation. Note that Gen3 is not affected.

To reproduce: bind and undbind an I2C slave on some bus, run
'i2cdetect' on that bus.

Fixes: de20d185 ("i2c: rcar: add slave support")
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@kernel.org>

In this test, loopback pkt is created and sent on default queue.
The packet goes until the Multi Port Switch (MPS) just before
the MAC and based on the specified channel number, it either
goes outside the wire on one of the physical ports or looped
back to Rx path by MPS. In this case, we're specifying loopback
channel, instead of physical ports, so the packet gets looped
back to Rx path, instead of getting transmitted on the wire.

v3:
- Modify commit message to include test details.
v2:
- Add only loopback self-test.
Signed-off-by: NVishal Kulkarni <vishal@chelsio.com>
Acked-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use eth_zero_addr() to clear mac address insetad of memset().
Signed-off-by: NMiaohe Lin <linmiaohe@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit adc0daad ("dm: report suspended
device during destroy") broke integrity recalculation.

The problem is dm_suspended() returns true not only during suspend,
but also during resume. So this race condition could occur:
1. dm_integrity_resume calls queue_work(ic->recalc_wq, &ic->recalc_work)
2. integrity_recalc (&ic->recalc_work) preempts the current thread
3. integrity_recalc calls if (unlikely(dm_suspended(ic->ti))) goto unlock_ret;
4. integrity_recalc exits and no recalculating is done.

To fix this race condition, add a function dm_post_suspending that is
only true during the postsuspend phase and use it instead of
dm_suspended().

Signed-off-by: Mikulas Patocka <mpatocka redhat com>
Fixes: adc0daad ("dm: report suspended device during destroy")
Cc: stable vger kernel org # v4.18+
Signed-off-by: NMike Snitzer <snitzer@redhat.com>