This function allows to send a HCI command without expecting any
controller event/response in return. This is allowed for vendor-
specific commands only.
Signed-off-by: NLoic Poulain <loic.poulain@linaro.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Local random address needs to be updated before creating connection if
RPA from LE Direct Advertising Report was resolved in host. Otherwise
remote device might ignore connection request due to address mismatch.

This was affecting following qualification test cases:
GAP/CONN/SCEP/BV-03-C, GAP/CONN/GCEP/BV-05-C, GAP/CONN/DCEP/BV-05-C

Before patch:
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6          #11350 [hci0] 84680.231216
        Address: 56:BC:E8:24:11:68 (Resolvable)
          Identity type: Random (0x01)
          Identity: F2:F1:06:3D:9C:42 (Static)
> HCI Event: Command Complete (0x0e) plen 4                        #11351 [hci0] 84680.246022
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7         #11352 [hci0] 84680.246417
        Type: Passive (0x00)
        Interval: 60.000 msec (0x0060)
        Window: 30.000 msec (0x0030)
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4                        #11353 [hci0] 84680.248854
      LE Set Scan Parameters (0x08|0x000b) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2             #11354 [hci0] 84680.249466
        Scanning: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4                        #11355 [hci0] 84680.253222
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18                          #11356 [hci0] 84680.458387
      LE Direct Advertising Report (0x0b)
        Num reports: 1
        Event type: Connectable directed - ADV_DIRECT_IND (0x01)
        Address type: Random (0x01)
        Address: 53:38:DA:46:8C:45 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Direct address type: Random (0x01)
        Direct address: 7C:D6:76:8C:DF:82 (Resolvable)
          Identity type: Random (0x01)
          Identity: F2:F1:06:3D:9C:42 (Static)
        RSSI: -74 dBm (0xb6)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2             #11357 [hci0] 84680.458737
        Scanning: Disabled (0x00)
        Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4                        #11358 [hci0] 84680.469982
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25          #11359 [hci0] 84680.470444
        Scan interval: 60.000 msec (0x0060)
        Scan window: 60.000 msec (0x0060)
        Filter policy: White list is not used (0x00)
        Peer address type: Random (0x01)
        Peer address: 53:38:DA:46:8C:45 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Own address type: Random (0x01)
        Min connection interval: 30.00 msec (0x0018)
        Max connection interval: 50.00 msec (0x0028)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Min connection length: 0.000 msec (0x0000)
        Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4                          #11360 [hci0] 84680.474971
      LE Create Connection (0x08|0x000d) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Create Connection Cancel (0x08|0x000e) plen 0    #11361 [hci0] 84682.545385
> HCI Event: Command Complete (0x0e) plen 4                        #11362 [hci0] 84682.551014
      LE Create Connection Cancel (0x08|0x000e) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19                          #11363 [hci0] 84682.551074
      LE Connection Complete (0x01)
        Status: Unknown Connection Identifier (0x02)
        Handle: 0
        Role: Master (0x00)
        Peer address type: Public (0x00)
        Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
        Connection interval: 0.00 msec (0x0000)
        Connection latency: 0 (0x0000)
        Supervision timeout: 0 msec (0x0000)
        Master clock accuracy: 0x00

After patch:
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7    #210 [hci0] 667.152459
        Type: Passive (0x00)
        Interval: 60.000 msec (0x0060)
        Window: 30.000 msec (0x0030)
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4                   #211 [hci0] 667.153613
      LE Set Scan Parameters (0x08|0x000b) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2        #212 [hci0] 667.153704
        Scanning: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4                   #213 [hci0] 667.154584
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18                     #214 [hci0] 667.182619
      LE Direct Advertising Report (0x0b)
        Num reports: 1
        Event type: Connectable directed - ADV_DIRECT_IND (0x01)
        Address type: Random (0x01)
        Address: 50:52:D9:A6:48:A0 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Direct address type: Random (0x01)
        Direct address: 7C:C1:57:A5:B7:A8 (Resolvable)
          Identity type: Random (0x01)
          Identity: F4:28:73:5D:38:B0 (Static)
        RSSI: -70 dBm (0xba)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2       #215 [hci0] 667.182704
        Scanning: Disabled (0x00)
        Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4                  #216 [hci0] 667.183599
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6    #217 [hci0] 667.183645
        Address: 7C:C1:57:A5:B7:A8 (Resolvable)
          Identity type: Random (0x01)
          Identity: F4:28:73:5D:38:B0 (Static)
> HCI Event: Command Complete (0x0e) plen 4                  #218 [hci0] 667.184590
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25    #219 [hci0] 667.184613
        Scan interval: 60.000 msec (0x0060)
        Scan window: 60.000 msec (0x0060)
        Filter policy: White list is not used (0x00)
        Peer address type: Random (0x01)
        Peer address: 50:52:D9:A6:48:A0 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Own address type: Random (0x01)
        Min connection interval: 30.00 msec (0x0018)
        Max connection interval: 50.00 msec (0x0028)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Min connection length: 0.000 msec (0x0000)
        Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4                    #220 [hci0] 667.186558
      LE Create Connection (0x08|0x000d) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19                    #221 [hci0] 667.485824
      LE Connection Complete (0x01)
        Status: Success (0x00)
        Handle: 0
        Role: Master (0x00)
        Peer address type: Random (0x01)
        Peer address: 50:52:D9:A6:48:A0 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Connection interval: 50.00 msec (0x0028)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Master clock accuracy: 0x07
@ MGMT Event: Device Connected (0x000b) plen 13          {0x0002} [hci0] 667.485996
        LE Address: 11:22:33:44:55:66 (OUI 11-22-33)
        Flags: 0x00000000
        Data length: 0
Signed-off-by: NSzymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

It should be __le16 instead of __u16 since its part of
mgmt API.
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

In case of using BT_ERR and BT_INFO, convert to bt_dev_err and
bt_dev_info when possible. This allows for controller specific
reporting.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch increases the connection timeout for LE connections that are
triggered by the advertising report to 4 seconds.

It has been observed that devices equipped with wifi+bt combo SoC fail
to create a connection with BLE devices due to their coexistence issues.
Increasing this timeout gives them enough time to complete the
connection with success.
Signed-off-by: NKonrad Zapałowicz <konrad.zapalowicz@canonical.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Signed-off-by: NLoic Poulain <loic.poulain@linaro.org>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If the LE Set Default PHY command is supported, the indicate to the
controller that the host has no preferences for transmitter PHY or
receiver PHY selection.

Issuing this command gives the controller a clear indication that other
PHY can be selected if available.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

If the Channel Selection Algorithm #2 feature is supported, then enable
the new LE Channel Selection Algorithm event.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Fix issue found during L2CAP qualification test TP/LE/CFC/BV-20-C.
Signed-off-by: NMarcin Kraglak <marcin.kraglak@tieto.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: NElena Reshetova <elena.reshetova@intel.com>
Signed-off-by: NHans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid Windsor <dwindsor@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We don't actually need the full rculist.h header in sched.h anymore,
we will be able to include the smaller rcupdate.h header instead.

But first update code that relied on the implicit header inclusion.
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Since we need to change the implementation, stop exposing internals.

Provide kref_read() to read the current reference count; typically
used for debug messages.

Kills two anti-patterns:

	atomic_read(&kref->refcount)
	kref->refcount.counter
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

bluetooth.h is not part of user API, so __ variants are not neccessary
here.
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The hci_get_route() API is used to look up local HCI devices, however
so far it has been incapable of dealing with anything else than the
public address of HCI devices. This completely breaks with LE-only HCI
devices that do not come with a public address, but use a static
random address instead.

This patch exteds the hci_get_route() API with a src_type parameter
that's used for comparing with the right address of each HCI device.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch enables prepending appearance value to scan response data.
It also adds support for setting appearance value through mgmt command.
If currently advertised instance has apperance flag set it is expired
immediately.
Signed-off-by: NMichał Narajowski <michal.narajowski@codecoup.pl>
Signed-off-by: NSzymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

While the subsystem version information are purely informational,
increase the minor number due to the addition of user channel and
management control monitoring suppport. It is helpful for debugging
purposes to see the version numbers change.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This command is used to retrieve the current state and basic
information of a controller. It is typically used right after
getting the response to the Read Controller Index List command
or an Index Added event (or its extended counterparts).

When any of the values in the EIR_Data field changes, the event
Extended Controller Information Changed will be used to inform
clients about the updated information.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NMichał Narajowski <michal.narajowski@codecoup.pl>

Instead of keeping a version string around, use version and revision
numbers and then stringify them for use as module parameter.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Instead of hiding everything behind a general managment events flag,
introduce indivdual flags that allow fine control over which events are
send to a given management channel.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This adds support for tracing all management commands and events via the
monitor interface.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This sends new notifications to the monitor support whenever a
management channel has been opened or closed. This allows tracing of
control channels really easily.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The mgmt version information will be also needed for the control
changell tracing feature. This provides a helper to pack them.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

To further allow unique identification and tracking of control socket,
store cookie and comm information when binding the socket.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Commit 5177a838 ("Bluetooth: Add debugfs fields for hardware and
firmware info") introduced hci_set_hw_info() and hci_set_fw_info().
These functions use kvasprintf_const() but are not marked with a
__printf attribute.  Adding such an attribute helps detecting issues
related to printf-formatting at build time.
Signed-off-by: NNicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch assigns the next free HCI device identifier to Bluetooth
devices based on the Qualcomm Shared Memory channels.
Signed-off-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The led_trigger field in hci_dev should be conditional based on if
CONFIG_BT_LEDS is set or not.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Some Bluetooth controllers allow for reading hardware and firmware
related vendor specific infos. If they are available, then they can be
exposed via debugfs now.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The protoypes for hci_recv_frame and hci_recv_diag are in the wrong
location in the header file. Move them close to all the other hci_dev
related exported functions.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

If link is disconnected due to Authentication Failure (PIN or Key
Missing status) userspace will be notified about this with proper error
code. Many LE profiles define "PIN or Key Missing" status as indication
of remote lost bond so this allows userspace to take action on this.

@ Device Connected: 88:63:DF:88:0E:83 (1) flags 0x0000
        02 01 1a 05 03 0a 18 0d 18 0b 09 48 65 61 72 74  ...........Heart
        20 52 61 74 65                                    Rate
> HCI Event: Command Status (0x0f) plen 4
      LE Read Remote Used Features (0x08|0x0016) ncmd 1
        Status: Success (0x00)
> ACL Data RX: Handle 3585 flags 0x02 dlen 11
      ATT: Read By Group Type Request (0x10) len 6
        Handle range: 0x0001-0xffff
        Attribute group type: Primary Service (0x2800)
> HCI Event: LE Meta Event (0x3e) plen 12
      LE Read Remote Used Features (0x04)
        Status: Success (0x00)
        Handle: 3585
        Features: 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00
          LE Encryption
< HCI Command: LE Start Encryption (0x08|0x0019) plen 28
        Handle: 3585
        Random number: 0x0000000000000000
        Encrypted diversifier: 0x0000
        Long term key: 26201cd479a0921b6f949f0b1fa8dc82
> HCI Event: Command Status (0x0f) plen 4
      LE Start Encryption (0x08|0x0019) ncmd 1
        Status: Success (0x00)
> HCI Event: Encryption Change (0x08) plen 4
        Status: PIN or Key Missing (0x06)
        Handle: 3585
        Encryption: Disabled (0x00)
< HCI Command: Disconnect (0x01|0x0006) plen 3
        Handle: 3585
        Reason: Authentication Failure (0x05)
> HCI Event: Command Status (0x0f) plen 4
      Disconnect (0x01|0x0006) ncmd 1
        Status: Success (0x00)
> HCI Event: Disconnect Complete (0x05) plen 4
        Status: Success (0x00)
        Handle: 3585
        Reason: Connection Terminated By Local Host (0x16)
@ Device Disconnected: 88:63:DF:88:0E:83 (1) reason 4

@ Device Connected: C4:43:8F:A3:4D:83 (0) flags 0x0000
        08 09 4e 65 78 75 73 20 35                       ..Nexus 5
> HCI Event: Command Status (0x0f) plen 4
      Authentication Requested (0x01|0x0011) ncmd 1
        Status: Success (0x00)
> HCI Event: Link Key Request (0x17) plen 6
        Address: C4:43:8F:A3:4D:83 (LG Electronics)
< HCI Command: Link Key Request Reply (0x01|0x000b) plen 22
        Address: C4:43:8F:A3:4D:83 (LG Electronics)
        Link key: 080812e4aa97a863d11826f71f65a933
> HCI Event: Command Complete (0x0e) plen 10
      Link Key Request Reply (0x01|0x000b) ncmd 1
        Status: Success (0x00)
        Address: C4:43:8F:A3:4D:83 (LG Electronics)
> HCI Event: Auth Complete (0x06) plen 3
        Status: PIN or Key Missing (0x06)
        Handle: 75
@ Authentication Failed: C4:43:8F:A3:4D:83 (0) status 0x05
< HCI Command: Disconnect (0x01|0x0006) plen 3
        Handle: 75
        Reason: Remote User Terminated Connection (0x13)
> HCI Event: Command Status (0x0f) plen 4
      Disconnect (0x01|0x0006) ncmd 1
        Status: Success (0x00)
> HCI Event: Disconnect Complete (0x05) plen 4
        Status: Success (0x00)
        Handle: 75
        Reason: Connection Terminated By Local Host (0x16)
@ Device Disconnected: C4:43:8F:A3:4D:83 (0) reason 4
Signed-off-by: NSzymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The HCI_BREDR naming is confusing since it actually stands for Primary
Bluetooth Controller. Which is a term that has been used in the latest
standard. However from a legacy point of view there only really have
been Basic Rate (BR) and Enhanced Data Rate (EDR). Recent versions of
Bluetooth introduced Low Energy (LE) and made this terminology a little
bit confused since Dual Mode Controllers include BR/EDR and LE. To
simplify this the name HCI_PRIMARY stands for the Primary Controller
which can be a single mode or dual mode controller.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Extend the set of possible HCI bus types with SPI and I2C.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Introduce a limited privacy mode indicated by value 0x02 to the mgmt
Set Privacy command.

With value 0x02 the kernel will use privacy mode with a resolvable
private address. In case the controller is bondable and discoverable
the identity address will be used.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add support for LED triggers to the Bluetooth subsystem and add kernel
config symbol BT_LEDS for it.

For now one trigger for indicating "HCI is powered up" is supported.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Having proper defines makes the code a bit readable, it also avoids
duplicating hard-coded values since these are also needed when
auto-allocating PSM values (in a subsequent patch).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch implements the mgmt Start Limited Discovery command. Most
of existing Start Discovery code is reused since the only difference
is the presence of a 'limited' flag as part of the discovery state.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To make the EIR parsing helper more general purpose, make it return
the found data and its length rather than just saying whether the data
was present or not.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This flag just tells us whether hdev->adv_instances is empty or not.
We can equally well use the list_empty() function to get this
information.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The request to update HCI during power on is always coming either from
hdev->req_workqueue or through an ioctl, so it's safe to use
hci_req_sync for it. This way we also eliminate potential races with
incoming mgmt commands or other actions while powering on.

Part of this refactoring is the splitting of mgmt_powered() into
mgmt_power_on() and __mgmt_power_off() functions. The main reason is
the different requirements as far as hdev locking is concerned, as
highlighted with the __ prefix of the power off API.

Since the power on in the case of clearing the AUTO_OFF flag cannot be
done synchronously in the set_powered mgmt handler, the hci_power_on
work callback is extended to cover this (which also simplifies the
set_powered helper a lot).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since the other discoverable changes are behind req_workqueue now it
only makes sense to move the discoverable timeout there as well.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>