To make the code more readable, this patch replaces
some magic numbers with macro or sizeof operation.

Also uses macro lower_32_bits and upper_32_bits to
get bits 0-31 and 32-63 of a number, instead of
using type conversion and '>>' operation.

No functional change.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there is a TX timeout, we can tell if the driver or stack
has stopped the queue by looking at state field, and when has
the last packet transmited by looking at trans_start field.

So this patch prints these two field in the
hns3_get_tx_timeo_queue_info().
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When reset fails, there is some information that will help for
finding out why does reset fail. and removes an unused
core_rst_cnt field in struct hclge_rst_stats.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver supports 2 types of core dumps.

1. Live dump - Firmware dump when system is up and running.
2. Crash dump - Dump which is collected during firmware crash
                that can be retrieved after recovery.
Crash dump is currently supported only on specific 58800 chips
which can be retrieved using OP-TEE API only, as firmware cannot
access this region directly.

User needs to set the dump flag using following command before
initiating the dump collection:

    $ ethtool -W|--set-dump eth0 N

Where N is "0" for live dump and "1" for crash dump

Command to collect the dump after setting the flag:

    $ ethtool -w eth0 data Filename

v3: Modify set_dump to support even when CONFIG_TEE_BNXT_FW=n.
Also change log message to netdev_info().

Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NSheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In error recovery process when firmware indicates that it is
completely down, initiate a firmware reset by calling OP-TEE API.

Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NSheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the check generic for any possible value, not only 2 and 4.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During recreation of original unsplit ports, just simply iterate over
the whole gap and recreate whatever originally existed.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code considers only split by 2 or 4. Make the base port
getting generic and allow split by 8 to be handled correctly. Generalize
the used port checks as well.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using constant value, use port_module_max_width which is
aligned with the cluster size.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't compute the original base local port during unsplit, rather
remember it in mlxsw_sp_port structure during split port creation.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Spectrum-3 the modules have 8 lanes, so split by count 2 results in
two split ports each of 4 lanes. Add a resource that can be used to
obtain local port offset in that case.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get local port offsets of split port in a separate helper function and
use it in both split and unsplit function.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver assumes certain values in the PMLP register. Add checks that
verify that PMLP register provides fitting values.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass the port mapping structure down to create, module_map and other
function instead of individual values.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't use constant max width value and instead of that, use the actual
width of the port. Also don't pass module value and use the value
stored in the same structure.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Store the initial PMLP register configuration into array of structures
instead of just simple array of module numbers.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when user does split, he is not able to distinguish if the
port cannot be split because it is already split, or because it cannot
be split at all. Add another check for split flag to distinguish this.
Also add check forbidding split when maximal width is 1.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fact that the port cannot be split further should be checked before
checking the count, so move it.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the max module width is hard-coded according to ASIC type.
That is not entirely correct, as the max module width might differ
per-board. Use PMTM register to query FW for maximal width of a module.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PMTM allows query or configuration of module types.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tx/rx lane fields got extended to 4 bits, update the reg field
description accordingly.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use '__skb_queue_purge()' instead of re-implementing it.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is more clear to use DEFINE_DEBUGFS_ATTRIBUTE to define debugfs file
operation rather than DEFINE_SIMPLE_ATTRIBUTE.

It is detected with the help of coccinelle.
Signed-off-by: Nzhong jiang <zhongjiang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This parameter has never been used.
Signed-off-by: NGuillaume Nault <gnault@redhat.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add downshift support for 88E1145, it uses the same downshift
configuration registers as 88E1111.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bonding uses the L4 ports to balance flows between slaves. As the ICMP
protocol has no ports, those packets are sent all to the same device:

    # tcpdump -qltnni veth0 ip |sed 's/^/0: /' &
    # tcpdump -qltnni veth1 ip |sed 's/^/1: /' &
    # ping -qc1 192.168.0.2
    1: IP 192.168.0.1 > 192.168.0.2: ICMP echo request, id 315, seq 1, length 64
    1: IP 192.168.0.2 > 192.168.0.1: ICMP echo reply, id 315, seq 1, length 64
    # ping -qc1 192.168.0.2
    1: IP 192.168.0.1 > 192.168.0.2: ICMP echo request, id 316, seq 1, length 64
    1: IP 192.168.0.2 > 192.168.0.1: ICMP echo reply, id 316, seq 1, length 64
    # ping -qc1 192.168.0.2
    1: IP 192.168.0.1 > 192.168.0.2: ICMP echo request, id 317, seq 1, length 64
    1: IP 192.168.0.2 > 192.168.0.1: ICMP echo reply, id 317, seq 1, length 64

But some ICMP packets have an Identifier field which is
used to match packets within sessions, let's use this value in the hash
function to balance these packets between bond slaves:

    # ping -qc1 192.168.0.2
    0: IP 192.168.0.1 > 192.168.0.2: ICMP echo request, id 303, seq 1, length 64
    0: IP 192.168.0.2 > 192.168.0.1: ICMP echo reply, id 303, seq 1, length 64
    # ping -qc1 192.168.0.2
    1: IP 192.168.0.1 > 192.168.0.2: ICMP echo request, id 304, seq 1, length 64
    1: IP 192.168.0.2 > 192.168.0.1: ICMP echo reply, id 304, seq 1, length 64

Aso, let's use a flow_dissector_key which defines FLOW_DISSECTOR_KEY_ICMP,
so we can balance pings encapsulated in a tunnel when using mode encap3+4:

    # ping -q 192.168.1.2 -c1
    0: IP 192.168.0.1 > 192.168.0.2: GREv0, length 102: IP 192.168.1.1 > 192.168.1.2: ICMP echo request, id 585, seq 1, length 64
    0: IP 192.168.0.2 > 192.168.0.1: GREv0, length 102: IP 192.168.1.2 > 192.168.1.1: ICMP echo reply, id 585, seq 1, length 64
    # ping -q 192.168.1.2 -c1
    1: IP 192.168.0.1 > 192.168.0.2: GREv0, length 102: IP 192.168.1.1 > 192.168.1.2: ICMP echo request, id 586, seq 1, length 64
    1: IP 192.168.0.2 > 192.168.0.1: GREv0, length 102: IP 192.168.1.2 > 192.168.1.1: ICMP echo reply, id 586, seq 1, length 64
Signed-off-by: NMatteo Croce <mcroce@redhat.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a similar fashion to Spectrum-1, enforce a specific firmware version
for Spectrum-2 so that the driver and firmware are always in sync with
regards to new features.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The version adds support for querying port module type. It will be used
by a followup patch set from Jiri to make port split code more generic.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SN3800 Spectrum-2 based systems have gearboxes that need to be
initialized by the firmware during its initialization flow. In certain
cases, the firmware might need to flash these gearboxes, which is
currently a time-consuming process.

In newer firmware versions, the firmware will not signal to the driver
that it is ready until the gearboxes are flashed. Increase the PCI reset
timeout for these situations. In normal cases, the driver will need to
wait no longer than 5 seconds.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In new firmware versions this register is extended with a sampling rate
for Spectrum-2 and future ASICs.

Increase the size of the register to ensure the field is initialized to
0 which means every packet is mirrored.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When CONFIG_PM_SLEEP is not defined compiler complain as follow:
CC [M]  drivers/net/ethernet/intel/e1000e/netdev.o
drivers/net/ethernet/intel/e1000e/netdev.c:6302:12: warning: ‘e1000e_s0ix_entry_flow’ defined but not used [-Wunused-function]
static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)
drivers/net/ethernet/intel/e1000e/netdev.c:6411:12: warning: ‘e1000e_s0ix_exit_flow’ defined but not used [-Wunused-function]
static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)
LD [M]  drivers/net/ethernet/intel/e1000e/e1000e.o

Add wrap to fix these warnings.
Reported-by: Nkbuild test robot <lpk@intel.com>
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add devices ID's for the next LOM generations that will be
available on the next Intel Client platform (Tiger Lake)
This patch provides the initial support for these devices
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a series from Alexander Duyck this change adds UDP segmentation
offload support to the i40e driver.

CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: NJosh Hunt <johunt@akamai.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Repost from a series by Alexander Duyck to add UDP segmentation offload
support to the igb driver:
https://lore.kernel.org/netdev/20180504003916.4769.66271.stgit@localhost.localdomain/

CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Willem de Bruijn <willemb@google.com>
Suggested-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJosh Hunt <johunt@akamai.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a series from Alexander Duyck this change adds UDP segmentation
offload support to the igb driver.

CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: NJosh Hunt <johunt@akamai.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we no longer check for __E1000_DOWN in e1000e_close we can drop the
spot where we were restoring the bit. This saves us a bit of unnecessary
complexity.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to address possible race conditions that can exist
between network configuration and power management. A similar issue was
fixed for igb in commit 9474933c ("igb: close/suspend race in
netif_device_detach").

In addition it consolidates the code so that the PCI error handling code
will essentially perform the power management freeze on the device prior to
attempting a reset, and will thaw the device afterwards if that is what it
is planning to do. Otherwise when we call close on the interface it should
see it is detached and not attempt to call the logic to down the interface
and free the IRQs again.

From what I can tell the check that was adding the check for __E1000_DOWN
in e1000e_close was added when runtime power management was added. However
it should not be relevant for us as we perform a call to
pm_runtime_get_sync before we call e1000_down/free_irq so it should always
be back up before we call into this anyway.
Reported-by: NMorumuri Srivalli <smorumu1@in.ibm.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: NDavid Dai <zdai@linux.vnet.ibm.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>

Add devices ID's for the next LOM generations that will be
available on the next Intel Client platform (Comet Lake)
This patch provides the initial support for these devices
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use true/false for bool type in bnxt_timer function.
Signed-off-by: NSaurav Girepunje <saurav.girepunje@gmail.com>
Acked-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use true/false on bool type variables for assignment.
Signed-off-by: NSaurav Girepunje <saurav.girepunje@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>