Add system clock detection to prevent output DC from SPO.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add platform specific data for Terra project.
Signed-off-by: NLuke_Yin@asus.com <Luke_Yin@asus.com>
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add platform specific data for Wizpig project.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add platform specific data for Edgar project.
Signed-off-by: NJohn Lin <john.lin@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Unmuting headphone has pop noise in particular hardware design. So we extend
the delay time in headphone unmuting sequence to avoid pop.
Signed-off-by: NJohn Lin <john.lin@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The patch adds the HWEQ function for the speaker output. User can set the
HWEQ parameters using the ALSA binary control byte-by-byte. We use the
following struct array to store the HWEQ parameters for implementing as
simple as possible.
struct rt5645_eq_param_s {
	unsigned short reg;
	unsigned short val;
};
It supports the variant length of the HWEQ parameters that are required.
We add the validating function in the function "rt5645_hweq_put" of the
ALSA binary control to avoid the user that puts the invalid parameters.
In the HWEQ enable function of speaker event, we also add the validating
function to prevent that the invalid parameters are applied to codec.
The HWEQ parameters should be controlled by DAPM for a specific sequence,
so the parameters will be applied to the codec in the speaker power up
event of DAPM, and will be disabled in the speaker power down event of
DAPM.
Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NJohn Lin <john.lin@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The patch rechecks the jack detect status after resuming from S3.
Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

We were getting build warning about "Section mismatch".
dmi_platform_intel_broadwell is being referenced from the probe function
rt5645_i2c_probe(), but dmi_platform_intel_broadwell was marked with
__initdata.
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The patch adds the codec reset setting in the shutdown function to prevent
the weird sound of the headphone happened by rebooting.
Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The codec supports 4 channel recording with TDM on AIF1.
This patch modifies the DAI capability to allow it.
Signed-off-by: NBen Zhang <benzh@chromium.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

ASoC: rt5645: Use the type SOC_DAPM_SINGLE_AUTODISABLE to prevent the weird sound in runtime of power up
Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Broadwell can not triger the IRQ falling and rising simultaneously,
so it can not detect jack-in and jack-out simultaneously.
We add a flag "jd_invert" to platform data. If this flag is set,
codec IRQ will be set to invert that forces IRQ as pulse when jack-in
and jack-out.
Signed-off-by: NJohn Lin <john.lin@realtek.com>
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add DMI data for Buddy project.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NJohn Lin <john.lin@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The patch removes the incorrect settings to avoid the pop sound in the
first playback with headphone after boot.
Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NJohn Lin <john.lin@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add i2c shutdown function to prevent the pop sound of the headphone while
the system is rebooting or shutdowning. It de-initials the jack detection
function, and it cannot be turned off in _BIAS_OFF. If we don't de-initial
it, the pop sound will be heard in the situation of powering off. And
replace the related register settings from magic number to meaningful
defined name.
Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The patch removes the incorrect setting of the JD mode. It will cause pop
sound in the booting time.
Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The patch corrects the sequence of the jack detection. It will prevent the
pop sound while the jack plug in.
Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

ASoC: rt5645: Modify the headphone depop and calibration function to prevent the pop sound in the booting time

Remove the original calibration function and modify the depop and
calibration function to prevent the pop sound in the booting time.
Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.

Generate using the following coccinelle script

// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
-	TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
	...
-};
+);
// </smpl>
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

I2S2_DAC pin can be used for I2S or GPIO. We should set it as GPIO
if we use GPIO5 as DMIC1 data pin.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

"ASoC: rt5645: Check if codec is initialized in workqueue handler"
adds a check if codec is NULL in rt5645_irq_detection, which
returns an int. However, "ASoC: rt5645: Remove irq_jack_detection
function" removes that function, and moves the code in
jack_detect_work, which returns void.

Remove the return value to fix compilation warning.
Signed-off-by: NNicolas Boichat <drinkcat@chromium.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

This adds basic regulator support for rt5645.
Signed-off-by: NKoro Chen <koro.chen@mediatek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The driver does not free irq when snd_soc_register_codec returns error.
It does not return error when request irq failed, either.

Add return when request irq failed, and free_irq if
snd_soc_register_codec failed.
Signed-off-by: NKoro Chen <koro.chen@mediatek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

"ASoC: rt5645: Simplify rt5645_enable_push_button_irq" removes
the test that accessed rt5645->pdata.jd_mode (that test is now
done in rt5645_jack_detect only), so we do not need that
variable anymore.
Signed-off-by: NNicolas Boichat <drinkcat@chromium.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

This fixes kernel panic on boot, if rt5645->codec is NULL when
rt5645_jack_detect_work is first called.

rt5645_jack_detect_work needs rt5645->codec to be initialized to setup
dapm pins. Also, reporting jack events is useless, as the jacks cannot
be set before the codec is ready.

Since we manually call the interrupt handler in
rt5645_set_jack_detect, the initial jack state will be reported
correctly, and dapm pins will be setup at that time.
Signed-off-by: NNicolas Boichat <drinkcat@chromium.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

Separate the functionality using sequences of register writes from the
functions that take register defaults. This change renames the arguments
in order to support the extension of reg_sequence to take an optional
delay to be applied after any given register in a sequence is written.
This avoids adding an int to all register defaults, which could
substantially increase memory usage for regmaps with large default tables.

This also updates all the clients of multi_reg_write/register_patch.
Signed-off-by: NNariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

LDO2/Mic Det Power pins are already enabled/disabled in rt5645_jack_detect
(the jack out code path previously did not disable those if button function
is enabled: modify it to make it so).
Signed-off-by: NNicolas Boichat <drinkcat@chromium.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

This makes sure the dapm state is consistent when the card is
instantiated.

However, if the card is not instantiated yet, we still update the
registers manually in the "jack in" case, so that we can immediately
report if a mic is present or not.

Disabling "Mic Det Power" after detection, and on jack out, can
wait until the card gets instantiated.
Signed-off-by: NNicolas Boichat <drinkcat@chromium.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The snd_soc_dai_ops variables are not modified after initialization in
these drivers, so make them const.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@kernel.org>