Signed-off-by: NAlexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NAlexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NAlexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NAlexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NAlexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NAlexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NAlexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NAlexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Delay the read of the EC status register until
after the event that caused it occurs -- otherwise
it is possible to read and act on stale status that was
associated with the previous event.

Do this with a perpetually incrementing "event_count" to detect
when a new event occurs and it is safe to read status.

There is no workaround for polling mode -- it is inherently
exposed to reading and acting on stale status, since it
doesn't have an interrupt to tell it the event completed.

http://bugzilla.kernel.org/show_bug.cgi?id=8110Signed-off-by: NAlexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Fix work queue code to support new model.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For the Freescale M5282 ColdFire,
Port UA Pin Assignment Register should set to UART mode.
Patch submitted by David Wu <davidwu@arcturusnetworks.com>.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The tlclk driver is going on the MPCBL005 so I need to make the Kconfig
more more generic.  Just some text changes.
Signed-off-by: NMark Gross <mark.gross@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Based on a patch from Don Howard <dhoward@redhat.com>

When calling write() with a buffer larger than 512 bytes, the
driver's write buffer overflows, allowing to overwrite the EIP and
execute arbitrary code with kernel privileges.

In read(), there exists a similar problem, but coming from the device.
A malicous or buggy device sending more than 512 bytes can overflow
of the driver's read buffer, with the same effects as above.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NHarald Welte <laforge@gnumonks.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

initramfs ended up depending on BLOCK:

  INITRAMFS_SOURCE <-- BLK_DEV_INITRD <-- BLOCK

This inhibits use of customized-initramfs-over-ramfs without block layer
(ramfs would still be enabled), useful in embedded applications.

Move BLK_DEV_INITRD out of 'drivers/block/Kconfig' and into 'init/Kconfig',
make it unconditional.
Signed-off-by: NDimitri Gorokhovik <dimitri.gorokhovik@free.fr>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds support for the struct pci_driver shutdown method to cciss.
 We require notification of an impending reboot or shutdown so that we can
flush the battery backed write cache (BBWC) on the Smart Array controller.
Signed-off-by: NMike Miller <mike.miller@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch changes the way we determine if a logical volume is larger than
2TB.

The original test looked for a total_size of 0.  Originally we added 1 to the
total_size.  That would make our read_capacity return size 0 for >2TB lv's.
We assumed that we could not have a lv size of 0 so it seemed OK until we were
in a clustered system.  The backup node would see a size of 0 due to the
reservation on the drive.  That caused the driver to switch to 16-byte CDB's
which are not supported on older controllers.  After that everything was
broken.

It may seem petty but I don't see the value in trying to determine if the LBA
is beyond the 2TB boundary.  That's why when we switch we use 16-byte CDB's
for all read/write operations.  Please consider this for inclusion.
Signed-off-by: NMike Miller <mike.miller@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the following error if FB_DDC=n

Kernel: arch/x86_64/boot/bzImage is ready  (#1)
  Building modules, stage 2.
  MODPOST 229 modules
WARNING: "fb_ddc_read" [drivers/video/nvidia/nvidiafb.ko] undefined!
make[1]: *** [__modpost] Error 1
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix implicit declarations and missing code in atyfb.

drivers/video/aty/atyfb_base.c:2137: warning: implicit declaration of function 'a
ty_ld_lcd'
drivers/video/aty/atyfb_base.c:2154: warning: implicit declaration of function 'a
ty_st_lcd'
atyfb_base.c:(.text+0x33e5c): undefined reference to `aty_ld_lcd'
atyfb_base.c:(.text+0x33eb2): undefined reference to `aty_st_lcd'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/video/nvidia/nv_backlight.c: In function 'nvidia_bl_init':
drivers/video/nvidia/nv_backlight.c:103: error: implicit declaration of function 'pmac_has_backlight_type'
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Release the device's irq during sleep, as all well-behaved drivers
should.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The interrupt is shared with another device, which resumes earlier than the
sdhci controller, and generates an interrupt.

The sdhci interrupt handler runs, sees 0xffffffff in its own device's
interrupt status, and tries to handle it..  The reason for the 0xffffffff
is that the device is still suspended, and *all* regs are reading back
0xffffffff.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The new high-speed timings are similar to each other and the old
system, but not identical. And although things "just work" most of
the time, sometimes it does not. So we need to start marking which
hosts are known to fully comply with the new timings.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

drivers/net/sis900.c: In function 'sis900_reset_phy':
drivers/net/sis900.c:972: warning: 'status' may be used uninitialized in this function
drivers/net/sis900.c: In function 'sis900_check_mode':
drivers/net/sis900.c:1431: warning: 'status' may be used uninitialized in this function
drivers/net/sis900.c: In function 'sis900_timer':
drivers/net/sis900.c:1467: warning: 'status' may be used uninitialized in this function
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

We were using the platform_device.id field to identify which ethernet
port is used for mv643xx_eth device.  This is not generally correct.
It will be incorrect, for example, if a hardware platform uses a single
port but not the first port.  Here, we add an explicit port_number field
to struct mv643xx_eth_platform_data.

This makes the mv643xx_eth_platform_data structure required, but that
isn't an issue since all users currently provide it already.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The PCnet32 driver always passed the the size of the largest possible packet
to the pci_dma_sync_single_for_cpu and pci_dma_sync_single_for_device.
This results in a fairly large "colateral damage" in the caches and makes
the flush operation itself much slower.  On a system with a 40MHz CPU this
patch increases network bandwidth by about 12%.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Acked-by: NDon Fry <pcnet32@verizon.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fixes MODPOST warnings similar to:

WARNING: drivers/net/tulip/de2104x.o - Section mismatch: reference to
.init.text:de_init_one from .data.rel.local after 'de_driver' (at offset 0x20)
WARNING: drivers/net/tulip/de2104x.o - Section mismatch: reference to
.exit.text:de_remove_one from .data.rel.local after 'de_driver' (at offset 0x28)
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Cc: Valerie Henson <val_henson@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Handle pci_enable_device() failure while resuming, we can safely exit here.
Signed-off-by: NMonakhov Dmitriy <dmonakhov@openvz.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add link detection
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix a oops on module removal due to deallocating memory before unregistring
driver Fix a NULL pointer dereference when dev_alloc_skb fails
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix a typo, wrap lines on 80-th column, change KERN_ERR to KERN_INFO for
link status message
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Revert 7628b0a8.  Thomas Bachler
reports:

  Commit 7628b0a8 (drivers/net/tulip/dmfe:
  support basic carrier detection) breaks networking on my Davicom DM9009.
  ethtool always reports there is no link.  tcpdump shows incoming packets,
  but TX is disabled.  Reverting the above patch fixes the problem.

Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Thomas Bachler <thomas@archlinux.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Returns NETDEV_TX_BUSY when BD ring is full.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix broken BD processing code.
Signed-off-by: NMichael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix two issues in this driver's netpoll path: one usual, with spin_unlock_irq()
enabling interrupts which nobody asks it to do (that has been fixed recently in
a number of drivers) and one unusual, with poll_controller() method possibly
causing loss of interrupts due to the interrupt status register being cleared
by a simple read and the interrpupt handler simply storing it, not accumulating.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	In active-backup mode, the current bonding code duplicates IGMP
traffic to all slaves, so that switches are up to date in case of a
failover from an active to a backup interface.  If bonding then fails
back to the original active interface, it is likely that the "active
slave" switch's IGMP forwarding for the port will be out of date until
some event occurs to refresh the switch (e.g., a membership query).

	This patch alters the behavior of bonding to no longer flood
IGMP to all ports, and to issue IGMP JOINs to the newly active port at
the time of a failover.  This insures that switches are kept up to date
for all cases.

	"GOELLESCH Niels" <niels.goellesch@eurocontrol.int> originally
reported this problem, and included a patch.  His original patch was
modified by Jay Vosburgh to additionally remove the existing IGMP flood
behavior, use RCU, streamline code paths, fix trailing white space, and
adjust for style.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	The ARP validation code only needs ARPs for the bonding device.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	Bonding can erroneously register the same packet_type to receive
ARPs (for use by ARP validation): once at device open time, and once via
sysfs.  Since sysfs can change the validate setting (and thus register
or unregister) at any time, a flag is needed to synchronize with device
open in order to avoid double registrations, and the simplest place is
within the packet_type structure itself.  Double unregister is not an
issue.

	Bug reported by Ulrich Oelmann <ulrich.oelmann@web.de>.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix wrong "port" calculations in pdc202xx_{configure_piomode,set_dmamode}()
They were broken for all configurations except one (master device on primary
channel, no other devices) and as a result device settings + PIO/DMA timings
were being programmed into the wrong PCI registers.  This could result in
a large variety of problems including data corruption, hangs etc. (depending
on devices used and your luck :-).

  ap->port_no   ap->devno   used PCI registers   correct PCI registers
            0           0            0x60-0x62               0x60-0x62
            0           1            0x62-0x64               0x64-0x66
            1           0            0x64-0x66               0x68-0x6a
            1           1            0x66-0x68               0x6c-0x6e

Also forward port recent fixes from drivers/ide pdc202xx_old driver:

* fix XFER_MW_DMA0 timings (they were overclocked, use the official ones)

* fix bitmasks for clearing bits of register B:

  - when programming DMA mode bit 0x10 of register B was cleared which
    resulted in overclocked PIO timing setting (iff PIO0 was used)

  - when programming PIO mode bits 0x18 weren't cleared so suboptimal
    timings were used for PIO1-4 if PIO0 was previously set (bit 0x10)
    and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08)

and finally bump driver version.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

pata_legacy fails to detect the disk on my old ISA/VLB 486:
it starts to probe io=0x1f0 ctr=0x3f6 irq=15, complains
loudly about IDENTIFYs timing out, and finally fails.
(Sorry I couldn't capture the kernel's boot messages.)

It turns out that the driver's mapping from io to irq in
legacy_irq[] is wrong: index 0 for io=0x1f0 has irq=15 but
should have irq=14, and index 1 for io=0x170 has irq=14 but
should have irq=15. This is confirmed by a comparison with
include/asm-i386/ide.h:ide_default_irq().

This patch swaps the first two elements in legacy_irq[],
which makes pata_legacy work on my 486.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jeff@garzik.org>