The wake-up interrupt bit is available on omap3/4/5 processors
unlike what we claim. Without fixing it we cannot use it on
omap3 and the system configured for wake-up events will just
hang on wake-up.

Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

SoC family definitions at the moment are reactive to board needs
as a result, beagle-xm would matchup with ti,omap3 which invokes
omap3430_init_early instead of omap3630_init_early. Obviously, this is
the wrong behavior.

With clock node dts conversion, we get the following warnings before
system hangs as a result and 3630 based platforms fails to boot
(uart4 clocks are only present in OMAP3630 and not present in
OMAP3430):

...
omap_hwmod: uart4: cannot clk_get main_clk uart4_fck
omap_hwmod: uart4: cannot _init_clocks

WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2434
_init+0x6c/0x80()
omap_hwmod: uart4: couldn't init clocks
...

WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: timer12: enabled state can only be entered from
initialized, idle, or disabled state
...

WARNING: CPU: 0 PID: 46 at arch/arm/mach-omap2/omap_hwmod.c:2224
_idle+0xd4/0xf8()
omap_hwmod: timer12: idle state can only be entered from enabled state

WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: uart4: enabled state can only be entered from
initialized, idle, or disabled state

So, add specific compatiblity for 3630 to allow match for Beagle-XM
platform.
Signed-off-by: NNishanth Menon <nm@ti.com>
[tony@atomide.com: left out ti,omap343x, updated comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add pinmux configuration for MCBSP2 connected to the TDM interface.
With this configuration the Headset modules works as expected.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Commit 76787b3b (ARM: OMAP2+: Remove board-4430sdp.c)
removed legacy booting in favor of device tree based booting
for 4430sdp. That caused the WLAN to stop working as the
related .dts entries fell through the cracks.

I don't have the "1283 PG 2.21 connectivity device" on my 4430sdp,
but the earlier version of this patch was tested by Luciano
Coelho. This version has left out the input logic for MMC CLK
line compared to the earlier version as that is not bidirectional,
and should be safe to do.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Luciano Coelho <luca@coelho.fi>
Cc: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Commit b42b9181 (ARM: OMAP2+: Remove board-omap4panda.c)
removed legacy booting in favor of device tree based booting
for pandaboard. That caused the WLAN to stop working as the
related .dts entries fell through the cracks.

The legacy muxing was setting pulls for GPIO 48 and 49, so let's
keep that behaviour for now to avoid further regressions for
BT and FM. Also input logic was enabled for MMC CLK line, but
I've verified that the input logic we don't need enabled for
CLK line as it's not bidirectional.

Also, we want to use non-removable instead of ti,non-removable
as the ti,non-removable also sets no_regulator_off_init which
is really not what we want as then wl12xx won't get powered
up and down which is needed for resetting it.

Note that looks like the WLAN interface fails to come up after
a warm reset, but that most likely was also happening with
the legacy booting and needs a separate fix.

Cc: Paolo Pisati <p.pisati@gmail.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Luciano Coelho <luca@coelho.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Fix the DTS data for ocp2scp node by adding the
missing reg property.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

USB3 block has a 64KiB space, another 64KiB is
used for the wrapper.

Without this change, resource_size() will get
confused and driver won't probe because size
will be negative.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The BeagleBone Black is basically a regular BeagleBone with eMMC and
HDMI added, so create a common dtsi both can use.

IMPORTANT: booting the existing am335x-bone.dts will blow up the HDMI
transceiver after a dozen boots with an uSD card inserted because LDO
will be at 3.3V instead of 1.8.

MMC support for AM335x still isn't in, so only the LDO change has been
added.
Signed-off-by: NKoen Kooi <koen@dominion.thruhere.net>
Tested-by: NTom Rini <trini@ti.com>
Tested-by: NMatt Porter <matt.porter@linaro.org>
Acked-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NJoel Fernandes <joelf@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The beagle and beagle-xm entries were inside the same double quote.
Split them to have two distinct entries.
Signed-off-by: NRobert Nelson <robertcnelson@gmail.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The patch "0b7a76aa ARM: dts: imx6q{dl}: add DTE pads for uart"
adds the DTE pads for uart. For PAD_EIM_D29, the offset of the
Pad Mux register should be 0x0c8, not 0x0c4.

This patch fixes it.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Commit 718a3500 (ARM: i.MX51: Add PATA support) adds pata support to the
imx51.dtsi file and is using clock 161. The problem is that the right
clock is 172, according to commit 5d530bb0 (ARM: i.MX5: Add PATA and SRTC
clocks).  Using the clock 172 makes things work again (and kills a nasty
system freeze).
Tested-by: NSteev Klimaszewski <steev@gentoo.org>
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

CSPI PER clock is per2clk (per2_gate id 60) instead of cspiX_ipg_gate.
Signed-off-by: NGwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The A20-olinuxino-micro has the EMAC wired in. Enable it in the DT so
that we can use it.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The Cubieboard2, just like its A10 counterpart, has the Ethernet wired
in. Enable it in the DT.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The A20 has several muxing options for the EMAC. Yet, the currently
supported boards only use one set of them. Add that pin set to the DTSI.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The Allwinner A20 SoC also have the EMAC found on the A10 and A10s.
Enable the support for it in the DTSI.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Since pwm-samsung bindings require at least one clock to be specified,
this patch adds the missing clocks and clock-names properties to specify
clocks used by PWM block on Exynos4 SoCs.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Replace the numerical polarity flags with the PWM_POLARITY_INVERTED
symbolic constant.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NThierry Reding <thierry.reding@gmail.com>

The Versatile Express V2P-CA15_A7 (aka TC2) has a CCI-400 which is
needed to get Multi-Cluster Power Management (MCPM) working.
Signed-off-by: NJon Medhurst <tixy@linaro.org>
Acked-by: NPawel Moll <pawel.moll@arm.com>
Acked-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

"dw-apb-timer-osc" and "dw-apb-timer-sp" are the same implementation of the
DW APB timer, just fed by different clocks. Thus, deprecate both
"dw-apb-timer-osc" and "dw-apb-timer-sp" in lieu of "dw-apb-timer".
Signed-off-by: NDinh Nguyen <dinguyen@altera.com>
Reviewed-by: NPavel Machek <pavel@denx.de>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
CC: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
CC: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
CC: Jamie Iles <jamie@jamieiles.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NOlof Johansson <olof@lixom.net>

v3:
- Split out a separate that cleans up the timer entries and clock information.
- Clearly states which binding is deprecated in the bindings doc.

v2:
- Deprecate the "dw-apb-timer-osc" and "dw-apb-timer-sp" but maintain
  backwards compatibility in the driver.

Fix phy0 address to match the reg property defined in phy0 node.
Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let's follow the ratified DT binding and use uartdm instead of
hsuart. This does break backwards compatibility but this
shouldn't be a problem because the uart driver isn't probing on
these devices without adding clock support (which isn't merged so
far).

Cc: David Brown <davidb@codeaurora.org>
Acked-by: NKumar Gala <galak@codeaurora.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

So I assumed that Beagle bone has only one USB port in host mode because
the micro USB connector had an USB-UART there. I was wrong a little. The
second port runs on host mode, but the micro USB plug is connected to an
internal HUB with two ports: one to the USB-UART and one to musb
instance one.
For that reason, this patch enables both ports: the primary in device
mode only and the second in host mode only.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This is what I observe:
On the first connect, the musb starts with DEVCTL.Session set. On
disconnect, musb_core calls try_idle. That functions removes the Session
bit signalizing that the session is over (something that only in OTG is
required). A new device, that is plugged, is no longer recognized.
I've setup a timer and checked the DEVCTL register and I haven't seen a
change in VBus and I saw the B-Device bit set. After setting the IDDIG
into A mode and forcing the device to behave like a A device, I didn't
see a change.
Neither VBUS goes to 0b11 nor does a session start request comes.
In the TI-v3.2 kernel they skip to call musb_platform_try_idle() in the
OTG_STATE_A_WAIT_BCON state while not in OTG mode.
Since the second port hast a standard A plug the patch changes the port
to run in host mode only and skips the timer which would remove
DEVCTL.Session so we can reconnect to another device later.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This relfects the code and dts requires changes due to recent .dts
binding updates:
- use mg prefix for the Metor Graphics specific attributes
- use power in mA not in mA/2 as specifed in the USB2.0 specification
- remove the child node for USB. This is driver specific on won't be
  reflected in the device tree
- use the "mentor" prefix instead of "mg".
- use "dr_mode" istead of "mg,port-mode" for the port mode. The former
  is used by a few other drivers.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

I forgot to separete the different names in the reg-names property. This
didn't cause anything to fail because the driver does not use the names
and simply relies on the order of the memory offsets in reg.
This patch fixes this in case it is used later.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch describe the phy used on atmel sama5d3 mother board:
 - phy address
 - phy interrupt pin
Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the clock driver knows about the available clocks found on the
A20, we can build up the clock tree from the device tree.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now that the clock driver has support for the A31 clocks, we can add
them to the DTSI and start using them in the relevant hardware blocks.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A10s has only a subset of the A10 gates. Now that the clock driver
has support for this gates set, switch to it in the DTSI.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: NEmilio López <emilio@elopez.com.ar>

Add ADC device tree node for exynos5420 and exynos5250
Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adds RTC DT node to Exynos5420 SoC
Signed-off-by: NVikas Sajjan <vikas.sajjan@linaro.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Moves the RTC DT node's "status" property from exynos5250 board
(arndale & snow) dts files to exynos5250.dtsi, since the bindings
in exynos5250.dtsi depicts the RTC h/w completely.
Signed-off-by: NVikas Sajjan <vikas.sajjan@linaro.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Fixes the RTC DT node name for Exynos5250 as per the DT node naming
convention.
Signed-off-by: NVikas Sajjan <vikas.sajjan@linaro.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

the old codes defined uart0_nostreamctrl_pins, but missed pingroup
and padmux definition for it. this patch fixes it.
Signed-off-by: NQipan Li <Qipan.Li@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NJosh Wu <josh.wu@atmel.com>

Signed-off-by: NJosh Wu <josh.wu@atmel.com>

The NFC driver code doesn't use atmel,has-nfc and atmel,use-nfc-sram.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>

enable i2c0 device on Vybrid VF610 Tower Board
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This adds one more I2C2 alternate pinmux entry.
GPIO1_2 <=> SCL
GPIO1_3 <=> SDA
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>