This patch determines the register bank for clock enable/disable and reset
based on the clock ID instead of hardcoding it in the tables describing the
clocks. This results in less data to be maintained in the tables, making the
code easier to understand. The full benefit of the change will be realized once
also other clocktypes will be table based.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>

The PLL output frequency is multiplied during the P-divider computation,
so it needs to be divided by the P-divider again before returning.

This fixes an issue where clk_round_rate() would return the multiplied
frequency instead of the real one after the P-divider.
Signed-off-by: NThierry Reding <treding@nvidia.com>

These clocks were named gr2d and gr3d on Tegra20 and Tegra30, so use the
same names on Tegra114 for consistency.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>

Add spread spectrum control for PLLE in Tegra114.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>

The power-on default parent for this clock is pll_m, which turns out to
be wrong. Previously, bootloader reparented this clock.  We'll do it in
the kernel as well, so that there's one less thing that we depend on
bootloader to initialize.
Signed-off-by: NAndrew Chew <achew@nvidia.com>
Signed-off-by: NMark Zhang <markz@nvidia.com>

Perform upwards rounding when calculating dividers for periph clks on Tegra30
and Tegra114.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>

pll_m will be the parent of gr2d/gr3d if we don't do this.
And because pll_m runs at a high rate so gr2d/gr3d will be
unstable. So change the parent of them to pll_c2.
Signed-off-by: NMark Zhang <markz@nvidia.com>
Acked-By: NPeter De Schrijver <pdeschrijver@nvidia.com>

In Tegra114, vde/gr_2d/gr_3d have 3 bits for clock source selection.
So change the clock init macro for these clocks from
"TEGRA_INIT_DATA_INT" to "TEGRA_INIT_DATA_INT8".

Besides, no one uses "TEGRA_INIT_DATA_INT" after this change, so
remove this macro.
Signed-off-by: NMark Zhang <markz@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Acked-By: NPeter De Schrijver <pdeschrijver@nvidia.com>

Tegra114 sbc1-sbc6 have more possible parent clocks than Tegra30.
So correct the parents and mux width for them.
Signed-off-by: NMark Zhang <markz@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NPeter De Schrijver <pdeschrijver@nvidia.com>

As the clock IDs are now specified in a header file, we can use those
definitions instead of maintaining an internal enum.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>

The lock bit on PLL_U does not seem to be working correctly and
sometimes never gets set when waiting for the PLL to come up.
Remove the TEGRA_PLL_USE_LOCK flag to use a constant delay.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add a CLK_SET_RATE_NO_REPARENT clock flag, which will prevent muxes
being reparented during clk_set_rate.

To avoid breaking existing platforms, all callers of clk_register_mux()
are adjusted to pass the new flag. Platform maintainers are encouraged
to remove the flag if they wish to allow mux reparenting on set_rate.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Chao Xie <xiechao.mail@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Emilio López" <emilio@elopez.com.ar>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrew Chew <achew@nvidia.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: spear-devel@list.st.com
Cc: linux-tegra@vger.kernel.org
Tested-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com> [tegra]
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [sunxi]
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com> [Zynq]
Signed-off-by: NMike Turquette <mturquette@linaro.org>

When the system suspends to LP1, the CPU clock source is switched to
CLK_M (12MHz Oscillator) during suspend/resume flow. The CPU clock
source is controlled by the CCLKG_BURST_POLICY register, and hence this
register must be restored during LP1 resume.

Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Adding suspend/resume function for tegra_cpu_car_ops. We only save and
restore the setting of the clock of CoreSight. Other clocks still need
to be taken care by clock driver.

Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add DFLL DVCO reset line control functions to the CAR IP block driver.

The DVCO present in the DFLL IP block has a separate reset line,
exposed via the CAR IP block.  This reset line is asserted upon SoC
reset.  Unless something (such as the DFLL driver) deasserts this
line, the DVCO will not oscillate, although reads and writes to the
DFLL IP block will complete.

Thanks to Aleksandr Frid <afrid@nvidia.com> for identifying this and
saving hours of debugging time.
Signed-off-by: NPaul Walmsley <pwalmsley@nvidia.com>
Cc: Aleksandr Frid <afrid@nvidia.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add the input clocks needed by the DFLL IP blocks.  Initialize them to
51MHz (as required by the DFLL GFD) and to use the PLL_P clock source.

This patch is a collaboration with Peter De Schrijver
<pdeschrijver@nvidia.com>.

Thanks to Laxman Dewangan <ldewangan@nvidia.com> for identifying the
requirement to keep the DFLL clocks enabled to resolve PWR_I2C timeout
issues.
Signed-off-by: NPaul Walmsley <pwalmsley@nvidia.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: NAndrew Chew <achew@nvidia.com>
Cc: Matthew Longnecker <mlongnecker@nvidia.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add clock functions to initialize, enable, and disable the FCPU clock
shapers, based on the FCPU voltage rail state.  These will be used by
the DFLL clocksource driver code.

This version of the patch contains a fix for a problem noticed by Andrew
Chew <achew@nvidia.com>, where some of the FINETRIM_R bitfields were
incorrectly defined.

Based on code originally written by Aleksandr Frid <afrid@nvidia.com>.
Signed-off-by: NPaul Walmsley <pwalmsley@nvidia.com>
Cc: Andrew Chew <achew@nvidia.com>
Reviewed-by: NAndrew Chew <achew@nvidia.com>
Cc: Matthew Longnecker <mlongnecker@nvidia.com>
Cc: Aleksandr Frid <afrid@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Registering pciex as peripheral clock instead of fixed clock
as tegra_perih_reset_assert(deassert) api of this clock api
gives warning and ultimately does not succeed to assert(deassert)
Signed-off-by: NJay Agarwal <jagarwal@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

PLLM has override bits in the PMC. Use those when PLLM_OVERRIDE_ENABLE
is set.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Define override bits for Tegra30 PLLM.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Define override bits for Tegra114 PLLM.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: fixed up trivial merge conflict]

PLLM can have override bits in the PMC. Describe those in the PLL parameters.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Use the correct parents for sclk according to the TRM.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The PLLRE flags weren't set correctly. Fixed in this patch.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The m,n,p fields don't have the same bit offset and width across all PLLs.
This patch allows SoC specific files to indicate the offset and width.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The pllp_out2 should be integer only, the fractional bit should always be 0.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The pllc and pllxc code weren't always using the correct pdiv_map to
map between the post divider value and the hw p field. This could result
in illegal values being programmed in the hw.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The msenc clock's register was set to the usb3 clock's register.
Signed-off-by: NMikko Perttunen <mperttunen@nvidia.com>
Acked-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Use common of_clk_init() function for clocks initialization.
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Reviewed-by: NThierry Reding <thierry.reding@gmail.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Tegra has a blink timer register that allows to modulate the
clk_32k clock before outputting it. Since clk_32k is presented to the
kernel as a fixed clock, make sure this register does not tamper with
the clock frequency and that clk_32k is outputted as-is, similarly to
what is done on t20 and t30.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Number of parents for clk_out_2 and clk_out_3 was incorrectly set
to clk_out1_parents. Even though it did not break anything since the
size was same better to fix.
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Reviewed-by: NThierry Reding <thierry.reding@gmail.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The conventional CPU hotplug sequence on the other Tegra chips, we will also
clock gate the CPU in tegra_cpu_kill() after the CPU was power gated. For
Tegra114, the flow controller will clock gate the CPU after the power down
sequence. But we still need to implement a empty function for disable_clock
to avoid kernel warning message.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

AC97 controller clock is hardwired to pll_a_out0.
Signed-off-by: NLucas Stach <dev@lynxeye.de>
Acked-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The USB clocks are just clock gates, so no need to set a specific clock.
In fact trying to set a specific clock is just a NOP if the requested
clockrate is the same as those of the parent (clk_m) or will trigger a
WARN_ON() if rates don't match up.

As we are not setting a specific rate, nor activating the clocks at
init, there is no point in keeping the the usb entries in the clock init
table.
Signed-off-by: NLucas Stach <dev@lynxeye.de>
Acked-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

A gap exists in the binding's clock ID definitions. Fix the clock driver
to be consistent. This allows pclk to be looked up through device tree
and prevents:

ERROR: could not get clock /pmc:pclk(0)
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The UART driver enables the console uart clock, so we don't need to do that
anymore in this file.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>