Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 08 4月, 2010 3 次提交
    • J
      cfg80211: Add local-state-change-only auth/deauth/disassoc · d5cdfacb
      由 Jouni Malinen 提交于 
      cfg80211 is quite strict on allowing authentication and association
commands only in certain states. In order to meet these requirements,
user space applications may need to clear authentication or
association state in some cases. Currently, this can be done with
deauth/disassoc command, but that ends up sending out Deauthentication
or Disassociation frame unnecessarily. Add a new nl80211 attribute to
allow this sending of the frame be skipped, but with all other
deauth/disassoc operations being completed.

Similar state change is also needed for IEEE 802.11r FT protocol in
the FT-over-DS case which does not use Authentication frame exchange
in a transition to another BSS. For this to work with cfg80211, an
authentication entry needs to be created for the target BSS without
sending out an Authentication frame. The nl80211 authentication
command can be used for this purpose, too, with the new attribute to
indicate that the command is only for changing local state. This
enables wpa_supplicant to complete FT-over-DS transition successfully.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      d5cdfacb
    • K
      wl1251: use DRIVER_NAME macro in wl1251_spi_driver · 7590a550
      由 Kalle Valo 提交于 
      Better use the macro for consistency, the content is the same anyway.
Signed-off-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      7590a550
    • B
      ath5k: Adaptive Noise Immunity (ANI) Implementation · 2111ac0d
      由 Bruno Randolf 提交于 
      This is an Adaptive Noise Imunity (ANI) implementation for ath5k. I have looked
at both ath9k and HAL sources (they are nearly the same), and even though i
have implemented some things differently, the basic algorithm is practically
the same, for now. I hope that this can serve as a clean start to improve the
algorithm later.

This also adds a possibility to manually control ANI settings, right now only
thru a debugfs file:
  * set lowest sensitivity (=highest noise immunity):
	echo sens-low > /sys/kernel/debug/ath5k/phy0/ani
  * set highest sensitivity (=lowest noise immunity):
	echo sens-high > /sys/kernel/debug/ath5k/phy0/ani
  * automatically control immunity (default):
	echo ani-on > /sys/kernel/debug/ath5k/phy0/ani
  * to see the parameters in use and watch them change:
	cat /sys/kernel/debug/ath5k/phy0/ani

Manually setting sensitivity will turn the automatic control off. You can also
control each of the five immunity parameters (noise immunity, spur immunity,
firstep, ofdm weak signal detection, cck weak signal detection) manually thru
the debugfs file.

This is tested on AR5414 and nearly doubles the thruput in a noisy 2GHz band.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      2111ac0d
  3. 07 4月, 2010 25 次提交
  5. 03 4月, 2010 7 次提交
  7. 01 4月, 2010 5 次提交