As reported by hermann pitton <hermann-pitton@arcor.de>, some devices
has a different chip id for em2710 (likely the older ones):

em28xx: New device @ 480 Mbps (eb1a:2710, interface 0, class 0)
em28xx #0: Identified as EM2710/EM2750/EM2751 webcam grabber (card=22)
em28xx #0: em28xx chip ID = 17
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Thanks to hermann pitton <hermann-pitton@arcor.de> for pointing this new
variation.
Tested-by: Nhermann pitton <hermann-pitton@arcor.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

em28xx doesn't have temporal scaling. However, on webcams, sensors are
capable of changing the output rate. So, VIDIOC_[G|S]_PARM ioctls should
be passed to the sensor for it to properly set frame rate.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Implement g_parm/s_parm ioctls. Those are used to check the current
frame rate (in fps) and to set it to a value. In practice, there are
only 15 possible different speeds, due to chip limits.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A user discovered that the Geniatech x8000 encountered a regression when
the xc3028 power management was introduced.  The xc3028 never recovers after
setting the powerdown register, which is probably because the xc3028 reset
GPIO is not properly configured.  Since I do not have access to the hardware
and thus cannot determine the correct GPIO configuration, just disable xc3028
power management on this board, which fixes the regression.

Thanks to user "ritec" for reporting the issue and testing the fix.

Cc: rictec <rictec@netcabo.pt>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The introduction of the zl10353 i2c gate control broke support for the
Geniatech board (which is not behind an i2 gate).  Add the needed parameter.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove the following build warning:

sms-cards.c: In function 'sms_board_event':
sms-cards.c:120: warning: unused variable 'board'

Thanks to Hans Verkuil for pointing this out.

The problem code has been #if 0'd for now, this will likely be
used again in the future, once the event interface is complete.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The iSight sends non-UVC status events through the interrupt endpoint. Those
invalid events are reported to the kernel log, resulting in a log flood.

Only log the events when the UVC_TRACE_STATUS flag is set.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Commit 50144aee broke the Samsung NC10
netbook webcam. Instead of applying the FIX_BANDWIDTH quirk to all ViMicro
devices, list the devices explicitly.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The current GPIO configuration breaks all Hauppauge devices.

The code being removed affects Hauppauge devices only,
and is the cause of the breakage.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Moving BOOT fixes problem.
Signed-off-by: NNils Kassube <kassube@gmx.net>
Acked-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Currently, the VIDIOC_S_STD ioctl just returns -EINVAL regardless of
the norm passed.  This patch sets cx23885_mpeg_template.tvnorms and
cx23885_mpeg_template.current_norm so that the VIDIOC_S_STD will work.

Thanks to Joseph Yasi for pointing this out, even though this particular
fix was already pushed into a development repository, merge priority of
this changeset has been escalated as a result of Joseph posting this
identical patch.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NJoseph A. Yasi <joe.yasi@gmail.com>
Reviewed-by: NSteven Toth <stoth@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Current tip is broken and does not switch back to DVB-T correctly
Signed-off-by: NSohail Syyed <linuxtv@hubstar.net>
Signed-off-by: NSteven Toth <stoth@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This device uses msp34xx and uses 2.048 MHz frequency for I2S
communication.

Thanks to Angelo Cano <acano@fastmail.fm> for pointing the issues with
this device and proposing an approach for fixing the issue.
Tested-by: NAngelo Cano <acano@fastmail.fm>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixes stack corruption bug present in dump_regs function of zl10353 and
qt1010 drivers: the buffer buf was one byte smaller than required -
there are 4 chars for address prefix, 16 * 3 chars for dump of 16 eeprom
bytes per line and 1 byte for zero ending the string required, i.e. 53
bytes, but only 52 were provided.

The one byte missing in stack based buffer buf can cause stack
corruption possibly leading to kernel oops, as discovered originally
with af9015 driver (af9015: fix stack corruption bug).
Signed-off-by: NJan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some mt9v011 webcams report 0x8332 chip version, instead of 0x8243. From
the revision history at the mt9v011 datasheet, it seems that the chip
version has changed from the first release of the chip.

Thanks-to hermann pitton <hermann-pitton@arcor.de> for pointing this to
me, on his tests with a Silvercrest webcam.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This mistakenly tested against sizeof(freqs) instead of the array size. Due to
the mask the only illegal value possible was 3.
Reported-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This mistakenly tests against sizeof(freqs) instead of the array size. Due to
the mask the only illegal value possible was 3.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

mclk_get_divisor uses pcdev->soc_host.dev, make sure it is initialized.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When enabling debug with v4l_debug set to 2 or greater, the driver
OOPS's on startup.  Checks dev pointer before dereferencing, in
order to prevent this OOPS.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

IOCTLS will never get handled if we dont connect
video_ioctl2 to mpeg_fops.ioctl
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Both tvaudio and the tuner share i2c address 0x42. The tvaudio module can
check whether it really is a tda9840, but the tuner can't. So the tvaudio
module must be loaded before the tuner module. This was also the case for
2.6.29, but the order was swapped in 2.6.30.

Thanks to Krzysztof Grygiencz for reporting and testing this.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A recent patch didn't take into account that frontends can be compiled into
the kernel.  Or that frontends compiled as modules can't be used by the
b2c2 driver if it is not a module itself.

Some frontends require multiple drivers, e.g. a demod driver and a tuner
driver.  The code for the frontend support was getting added if the demod
driver was available.  Change this to also require any needed tuner or SEC
drivers as well.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is not just pure cosmetic, since the order affects the out-of-tree
module build at the -hg development tree.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NBrian Johnson <brijohn@gmail.com>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NBrian Johnson <brijohn@gmail.com>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Request demodulator auto-detect transmission parameters in case of
garbage parameters provided by application for compatibility.
That's needed at least for MPlayer compatibility currently.

Thanks to Jelle de Jong for reporting issue and providing SSH access to
Devin for debugging.

Thanks to Devin Heitmueller for hard debug work he did to find that bug.

Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The bug was introduced when adding the light frequency control
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When the change was introduced in the zl10353 for the i2c gate behavior, this
broke the HVR-900 which was not behind a gate.  Use a version of the zl10353
config profile that indicates the tuner is not behind such a gate.

Without this patch the first tune succeeds, but subsequent tuning attempts
will fail.

The change also renames the terratec zl10353 profile I wrote to be more
generic, since it is shared by the non-terratec device.

Thanks to Michael Krufky for providing a HVR-900 and DVB-T environment to test
with.

Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Pinnacle Hybrid Pro 320e was missing a demod config for the xc3028, which
is required for digital tuning to work properly.  Add the missing profile.

Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment.

Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In cases where the device has a generic Empia USB ID, the call in the
precard setup phase did not set the tuner GPIO.  As a result, the tuner may
not be taken out of reset before attempting initialization in the analog
driver.

This problem was not seen before with the EVGA inDtube, since that particular
board has the analog GPIO setup to include taking the tuner out of reset.

Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment for the Pinnacle 320e.

Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Set the GPIO properly for the analog side of the Pinnacle Hybrid Pro, or else
the emp202 doesn't get detected properly.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Setup the GPIOs properly and enable support for the DVB side of the Pinnacle
Hybrid Pro USB stick.

Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment.

Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Andy walls pointed out that we were passing 0x5d to the TUNER_GO register,
instead of 0x01.  Set the register properly (note the code did still work with
the incorrect value, so this does not address a regression).

Thanks to Andy Walls for noticing the issue.

Cc: Andy Walls <awalls@radix.net>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Terratec Cinergy T XS USB can have either a zl10353 or an mt352.  Add
support for the MT352 variant.

Thanks to Jelle de Jong for providing a unit to test/debug with.

Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Thanks to Wally <wally@voosen.eu> for bringing the issue and helping
with the tests.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>