Removing BUG_ON()
Signed-off-by: NWoojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

lan78xx.c:2282 tx_complete() warn: variable dereferenced before check 'skb' (see line 2249)
lan78xx.c:2885 lan78xx_bh() info: ignoring unreachable code.
lan78xx.c:3159 lan78xx_probe() info: ignoring unreachable code.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NWoojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

altera_tse_private->sgdmadesclen is always assigned assigned the same
value and never changes during runtime.  Remove the struct member and
use a new define for sizeof(struct sgdma_descrip) instead.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: mv88e6xxx: support switchdev FDB objects

This patchset refactors the FDB management in the mv88e6xxx code and adds the
glue in DSA to use the switchdev FDB objects.

Below is an usage example (ports 0-2 belongs to br0, ports 3-4 belongs to br1):

    # bridge fdb add 3c:97:0e:11:30:6e dev swp2
    # bridge fdb add 3c:97:0e:11:40:78 dev swp3
    # bridge fdb add 3c:97:0e:11:50:86 dev swp4
    # bridge fdb del 3c:97:0e:11:40:78 dev swp3
    # bridge fdb
    01:00:5e:00:00:01 dev eth0 self permanent
    01:00:5e:00:00:01 dev eth1 self permanent
    00:50:d2:10:78:15 dev swp0 master br0 permanent
    3c:97:0e:11:30:6e dev swp2 self static
    00:50:d2:10:78:15 dev swp3 master br1 permanent
    3c:97:0e:11:50:86 dev swp4 self static
    # cat /sys/kernel/debug/dsa0/atu
    # DB   T/P  Vec State Addr
    # 001  Port 004   e   3c:97:0e:11:30:6e
    # 004  Port 010   e   3c:97:0e:11:50:86

For the 88E6xxx switches, FIDs 1 to num_ports will be reserved for non-bridged
ports and bridge groups, and the remaining will be later used by VLANs.

This change is necessary to welcome the support for hardware VLANs (which will
follow soon).

Changes in v3:

 - reorder commits to improve bisectability and minimize diffs

 - add an ndm_state member in switchdev_fdb_obj instead of an is_static boolean

 - drop the need to convert unsigned char *addr to u8 addr[ETH_ALEN]
   (it is casted to char pointer anyway)

Changes in v2:

 - remove ndo_bridge_{get,set,del}link from switchdev/DSA glue code

 - use ether_addr_copy instead of memcpy for MAC addresses

 - constify MAC address in port_fdb_{add,del}

 - split the mv88e6xxx code refactoring into several patches
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the switchdev_port_obj_{add,del,dump} functions in DSA to
support the SWITCHDEV_OBJ_PORT_FDB objects.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds an ndm_state member to the switchdev_obj_fdb structure,
in order to support static FDB addresses.

Set Rocker ndm_state to NUD_REACHABLE.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a low level _mv88e6xxx_atu_getnext function for convenient access to
the hardware, and rework the FDB Get Next operation.

This will ease the future integration with VLAN IDs.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a mv88e6xxx_atu_entry structure and a low level function for the ATU
Load operation, and provide FDB add and delete wrappers functions.

This implementation handles the eventual trunk mapping. If the related
bit is set, then the ATU data register would contain the trunk ID, and
not the port vector.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the prototype of port_getnext to include a vid parameter.

This is necessary to introduce the support for VLAN.

Also rename the fdb_{add,del,getnext} function pointers to
port_fdb_{add,del,getnext} since they are specific to a given port.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the __mv88e6xxx_{read,write}_addr functions to more explicit
_mv88e6xxx_atu_mac_{read,write} functions, which also respect the single
underscore convention used in the file (meaning SMI lock must be held).
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver currently manages one FID per port (or bridge group), with a
mask of DSA_MAX_PORTS bits, where 0 means that the FID is in use.

The Marvell 88E6xxx switches support up to 4094 FIDs (from 1 to 0xfff;
FID 0 means that multiple address databases are not being used).

This patch changes the fid_mask for an fid_bitmap of 4096 bits.

>From now on, FIDs 1 to num_ports are reserved for non-bridged ports and
bridge groups (a bridge group gets the FID of its first member). The
remaining bits will be reserved for VLAN entries.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define register GLOBAL_ATU_FID instead of the raw value 0x01.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit f1d5ca43, reversing
changes made to 4933d85c.

I applied v2 instead of v3.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a build error that "'struct bpf_array' has no member
named 'prog'" on s390. In commit 2a36f0b9 ("bpf: Make the
bpf_prog_array_map more generic"), the member 'prog' of struct
bpf_array is replaced by 'ptrs'. So this patch fixes it.

Fixes: 2a36f0b9 ("bpf: Make the bpf_prog_array_map more generic")
Reported-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NKaixu Xia <xiakaixu@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David Daney says:

====================
net: thunder: Add ACPI support.

Change from v1:  Drop PHY binding part, use fwnode_property* APIs.

The first patch (1/2) rearranges the existing code a little with no
functional change to get ready for the second.  The second (2/2) does
the actual work of adding support to extract the needed information
from the ACPI tables.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently there is no way to get the MAC address in a firmware
independent manner, so set the MAC address of the device directly from
the ACPI tables.

The binding agrees with the proposed standard here:

http://www.uefi.org/sites/default/files/resources/nic-request-v2.pdf

Based on code from: Narinder Dhillon <ndhillon@cavium.com>
                    Tomasz Nowicki <tomasz.nowicki@linaro.org>
                    Robert Richter <rrichter@cavium.com>
Signed-off-by: NTomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: NRobert Richter <rrichter@cavium.com>
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Separate DT code in preparation for follow-on ACPI integration.

Based on code from: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: NRobert Richter <rrichter@cavium.com>
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When too many remotes are bound to an FDB entry, index may not be increased.
This problem will be caused on the large scale environment that is based on
the unicast default destination, for instance.
Signed-off-by: NAtzm Watanabe <atzm@iij.ad.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use '%zx' to print size_t format in order to fix the following build warning:

drivers/net/ethernet/mellanox/mlxsw/item.h:65:3: warning: format '%lx' expects argument of type 'long unsigned int', but argument 6 has type 'size_t' [-Wformat=]
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change isdn driver, remove reverse_bits() function,
use the generic revbit8() function instead.
Signed-off-by: Nyalin wang <yalin.wang2010@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add or remove some tabs so that statements line up correctly.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using a cluster of switches, some topologies will have an MDIO
bus per switch, not one for the whole cluster. Allow this to be
represented in the device tree, by adding an optional mii-bus property
at the switch level. The old platform_device method of instantiation
supports this already, so only the device tree binding needs extending
with an additional optional phandle.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add register definitions #defines for accessing the EEPROM.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pravin B Shelar says:

====================
GRE: Use flow based tunneling for OVS GRE vport.

Following patches make use of new Using GRE tunnel meta data
collection feature. This allows us to directly use netdev
based GRE tunnel implementation. While doing so I have
removed GRE demux API which were targeted for OVS. Most
of GRE protocol code is now consolidated in ip_gre module.

v5-v4:
Fixed Kconfig dependency for vport-gre module.

v3-v4:
Added interface to ip-gre device to enable meta data collection.
While doing this I split second patch into two patches.

v2-v3:
Add API to create GRE flow based device.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support for sharing GREPROTO_CISCO port was added so that
OVS gre port and kernel GRE devices can co-exist. After
flow-based tunneling patches OVS GRE protocol processing
is completely moved to ip_gre module. so there is no need
for GRE protocol hook. Following patch consolidates
GRE protocol related functions into ip_gre module.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using GRE tunnel meta data collection feature, we can implement
OVS GRE vport. This patch removes all of the OVS
specific GRE code and make OVS use a ip_gre net_device.
Minimal GRE vport is kept to handle compatibility with
current userspace application.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following patch create new tunnel flag which enable
tunnel metadata collection on given device.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function will be used in gre and geneve vport implementations.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add an explicit neighbour table overflow message (ratelimited) and
statistic to make diagnosing neighbour table overflows tractable in
the wild.

Diagnosing a neighbour table overflow can be quite difficult in the wild
because there is no explicit dmesg logged.  Callers to neighbour code
seem to use net_dbg_ratelimit when the neighbour call fails which means
the "base message" is not emitted and the callback suppressed messages
from the ratelimiting can end-up juxtaposed with unrelated messages.
Further, a forced garbage collection will increment a stat on each call
whether it was successful in freeing-up a table entry or not, so that
statistic is only a hint.  So, add a net_info_ratelimited message and
explicit statistic to the neighbour code.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the ability to toggle the vlan filtering support via
netlink. Since we're already running with rtnl in .changelink() we don't
need to take any additional locks.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shahed Shaikh says:

====================
qlcnic: enhancements

This series adds few enhancements.

  o Patch from Harish reorders the sequence of header files inclusion,
    keeping kernel's header files on top.

  o Firmware introduced a new feature which allows driver to increases
    the size of firmware dump of iSCSI function which is being collected
    by NIC driver.

  o Print buffer address which is holding a firmware dump.

  o Use vzalloc() instead kzalloc() for allocating large chunk of memory
    which will avoid potential memory allocation failure.

  o Add new device ID for 0x8C30 which is a 83xx series based VF function.

Please apply this series to net-next.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver allocates a large chunk of temporary buffer using kzalloc
to copy FW image. As there is no real need of this memory to be
physically contiguous, use vzalloc instead.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a 83xx series based VF device
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some cases it is required to capture minidump for iSCSI functions
as part of default minidump collection process. To enable this, firmware
exports it's capability and driver need to enable that capability
by issuing a mailbox command.

With this feature, firmware can provide additional iSCSI function's
minidump with smaller minidump capture mask (0x1f).
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Include local headers files after kernel's header files.
Signed-off-by: NHarish Patil <harish.patil@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the Marvel 88e1111 PHY only two SGMII modes are available, both
allowing only SGMII to copper mode (with or without clock). SGMII
to fiber mode is not supported. Make sure the fiber/copper registers
selector bits are cleared for selecting copper mode.
Signed-off-by: NMadalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we transmit a fragmented skb, we may run into a race like the
following scenario (assume txq->cur_tx is next to txq->dirty_tx):
           cpu 0                                          cpu 1
  fec_enet_txq_submit_skb
    reserve a bdp for the first fragment
    fec_enet_txq_submit_frag_skb
       update the bdp for the other fragment
       update txq->cur_tx
                                                   fec_enet_tx_queue
                                                     bdp = fec_enet_get_nextdesc(txq->dirty_tx, fep, queue_id);
                                                     This bdp is the bdp reserved for the first segment. Given
                                                     that this bdp BD_ENET_TX_READY bit is not set and txq->cur_tx
                                                     is already pointed to a bdp beyond this one. We think this is a
                                                     completed bdp and try to reclaim it.
    update the bdp for the first segment
    update txq->cur_tx

So we shouldn't update the txq->cur_tx until all the update to the
bdps used for fragments are performed. Also add the corresponding
memory barrier to guarantee that the update to the bdps, dirty_tx and
cur_tx performed in the proper order.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Couple of fixes/adjustments

Ido Schimmel (5):
  mlxsw: Call free_netdev when removing port
  mlxsw: Make system port to local port mapping explicit
  mlxsw: Simplify mlxsw_sx_port_xmit function
  mlxsw: Use correct skb length when dumping payload
  mlxsw: Fix use-after-free bug in mlxsw_sx_port_xmit

Jiri Pirko (2):
  mlxsw: Make pci module dependent on HAS_DMA and HAS_IOMEM
  mlxsw: Strip FCS from incoming packets
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>