Skip to content

K
Kernel

openeuler / Kernel
大约 1 年 前同步成功

通知 5
Star 0
Fork 0
K
Kernel

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 16 12月, 2008 3 次提交
    • H
      net: Add Generic Receive Offload infrastructure · d565b0a1
      由 Herbert Xu 提交于 
      This patch adds the top-level GRO (Generic Receive Offload) infrastructure.
This is pretty similar to LRO except that this is protocol-independent.
Instead of holding packets in an lro_mgr structure, they're now held in
napi_struct.

For drivers that intend to use this, they can set the NETIF_F_GRO bit and
call napi_gro_receive instead of netif_receive_skb or just call netif_rx.
The latter will call napi_receive_skb automatically.  When napi_gro_receive
is used, the driver must either call napi_complete/napi_rx_complete, or
call napi_gro_flush in softirq context if the driver uses the primitives
__napi_complete/__napi_rx_complete.

Protocols will set the gro_receive and gro_complete function pointers in
order to participate in this scheme.

In addition to the packet, gro_receive will get a list of currently held
packets.  Each packet in the list has a same_flow field which is non-zero
if it is a potential match for the new packet.  For each packet that may
match, they also have a flush field which is non-zero if the held packet
must not be merged with the new packet.

Once gro_receive has determined that the new skb matches a held packet,
the held packet may be processed immediately if the new skb cannot be
merged with it.  In this case gro_receive should return the pointer to
the existing skb in gro_list.  Otherwise the new skb should be merged into
the existing packet and NULL should be returned, unless the new skb makes
it impossible for any further merges to be made (e.g., FIN packet) where
the merged skb should be returned.

Whenever the skb is merged into an existing entry, the gro_receive
function should set NAPI_GRO_CB(skb)->same_flow.  Note that if an skb
merely matches an existing entry but can't be merged with it, then
this shouldn't be set.

If gro_receive finds it pointless to hold the new skb for future merging,
it should set NAPI_GRO_CB(skb)->flush.

Held packets will be flushed by napi_gro_flush which is called by
napi_complete and napi_rx_complete.

Currently held packets are stored in a singly liked list just like LRO.
The list is limited to a maximum of 8 entries.  In future, this may be
expanded to use a hash table to allow more flows to be held for merging.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d565b0a1
    • H
      net: Add frag_list support to GSO · 1a881f27
      由 Herbert Xu 提交于 
      This patch allows GSO to handle frag_list in a limited way for the
purposes of allowing packets merged by GRO to be refragmented on
output.

Most hardware won't (and aren't expected to) support handling GRO
frag_list packets directly.  Therefore we will perform GSO in
software for those cases.

However, for drivers that can support it (such as virtual NICs) we
may not have to segment the packets at all.

Whether the added overhead of GRO/GSO is worthwhile for bridges
and routers when weighed against the benefit of potentially
increasing the MTU within the host is still an open question.
However, for the case of host nodes this is undoubtedly a win.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      1a881f27
    • R
      Define smp_call_function_many for UP · d2ff9118
      由 Rusty Russell 提交于 
      Otherwise those using it in transition patches (eg. kvm) can't compile
with CONFIG_SMP=n:

arch/x86/kvm/../../../virt/kvm/kvm_main.c: In function 'make_all_cpus_request':
arch/x86/kvm/../../../virt/kvm/kvm_main.c:380: error: implicit declaration of function 'smp_call_function_many'
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      d2ff9118
  3. 13 12月, 2008 6 次提交
  5. 11 12月, 2008 15 次提交
  7. 10 12月, 2008 1 次提交
    • N
      netpoll: fix race on poll_list resulting in garbage entry · 7b363e44
      由 Neil Horman 提交于 
      	A few months back a race was discused between the netpoll napi service
path, and the fast path through net_rx_action:
http://kerneltrap.org/mailarchive/linux-netdev/2007/10/16/345470

A patch was submitted for that bug, but I think we missed a case.

Consider the following scenario:

INITIAL STATE
CPU0 has one napi_struct A on its poll_list
CPU1 is calling netpoll_send_skb and needs to call poll_napi on the same
napi_struct A that CPU0 has on its list



CPU0						CPU1
net_rx_action					poll_napi
!list_empty (returns true)			locks poll_lock for A
						 poll_one_napi
						  napi->poll
						   netif_rx_complete
						    __napi_complete
						    (removes A from poll_list)
list_entry(list->next)


In the above scenario, net_rx_action assumes that the per-cpu poll_list is
exclusive to that cpu.  netpoll of course violates that, and because the netpoll
path can dequeue from the poll list, its possible for CPU0 to detect a non-empty
list at the top of the while loop in net_rx_action, but have it become empty by
the time it calls list_entry.  Since the poll_list isn't surrounded by any other
structure, the returned data from that list_entry call in this situation is
garbage, and any number of crashes can result based on what exactly that garbage
is.

Given that its not fasible for performance reasons to place exclusive locks
arround each cpus poll list to provide that mutal exclusion, I think the best
solution is modify the netpoll path in such a way that we continue to guarantee
that the poll_list for a cpu is in fact exclusive to that cpu.  To do this I've
implemented the patch below.  It adds an additional bit to the state field in
the napi_struct.  When executing napi->poll from the netpoll_path, this bit will
be set. When a driver calls netif_rx_complete, if that bit is set, it will not
remove the napi_struct from the poll_list.  That work will be saved for the next
iteration of net_rx_action.

I've tested this and it seems to work well.  About the biggest drawback I can
see to it is the fact that it might result in an extra loop through
net_rx_action in the event that the device is actually contended for (i.e. the
netpoll path actually preforms all the needed work no the device, and the call
to net_rx_action winds up doing nothing, except removing the napi_struct from
the poll_list.  However I think this is probably a small price to pay, given
that the alternative is a crash.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7b363e44
  9. 09 12月, 2008 3 次提交
  11. 08 12月, 2008 4 次提交
    • G
      dccp ccid-2: Phase out the use of boolean Ack Vector sysctl · 6fdd34d4
      由 Gerrit Renker 提交于 
      This removes the use of the sysctl and the minisock variable for the Send Ack
Vector feature, as it now is handled fully dynamically via feature negotiation
(i.e. when CCID-2 is enabled, Ack Vectors are automatically enabled as per
 RFC 4341, 4.).

Using a sysctl in parallel to this implementation would open the door to
crashes, since much of the code relies on tests of the boolean minisock /
sysctl variable. Thus, this patch replaces all tests of type

	if (dccp_msk(sk)->dccpms_send_ack_vector)
		/* ... */
with
	if (dp->dccps_hc_rx_ackvec != NULL)
		/* ... */

The dccps_hc_rx_ackvec is allocated by the dccp_hdlr_ackvec() when feature
negotiation concluded that Ack Vectors are to be used on the half-connection.
Otherwise, it is NULL (due to dccp_init_sock/dccp_create_openreq_child),
so that the test is a valid one.

The activation handler for Ack Vectors is called as soon as the feature
negotiation has concluded at the
 * server when the Ack marking the transition RESPOND => OPEN arrives;
 * client after it has sent its ACK, marking the transition REQUEST => PARTOPEN.

Adding the sequence number of the Response packet to the Ack Vector has been
removed, since
 (a) connection establishment implies that the Response has been received;
 (b) the CCIDs only look at packets received in the (PART)OPEN state, i.e.
     this entry will always be ignored;
 (c) it can not be used for anything useful - to detect loss for instance, only
     packets received after the loss can serve as pseudo-dupacks.

There was a FIXME to change the error code when dccp_ackvec_add() fails.
I removed this after finding out that:
 * the check whether ackno < ISN is already made earlier,
 * this Response is likely the 1st packet with an Ackno that the client gets,
 * so when dccp_ackvec_add() fails, the reason is likely not a packet error.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6fdd34d4
    • G
      dccp: Remove manual influence on NDP Count feature · 4098dce5
      由 Gerrit Renker 提交于 
      Updating the NDP count feature is handled automatically now:
 * for CCID-2 it is disabled, since the code does not use NDP counts;
 * for CCID-3 it is enabled, as NDP counts are used to determine loss lengths.

Allowing the user to change NDP values leads to unpredictable and failing
behaviour, since it is then possible to disable NDP counts even when they
are needed (e.g. in CCID-3).

This means that only those user settings are sensible that agree with the
values for Send NDP Count implied by the choice of CCID. But those settings
are already activated by the feature negotiation (CCID dependency tracking),
hence this form of support is redundant.

At startup the initialisation of the NDP count feature uses the default
value of 0, which is done implicitly by the zeroing-out of the socket when
it is allocated. If the choice of CCID or feature negotiation enables NDP
count, this will then be updated via the NDP activation handler.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4098dce5
    • G
      dccp: Remove obsolete parts of the old CCID interface · 0049bab5
      由 Gerrit Renker 提交于 
      The TX/RX CCIDs of the minisock are now redundant: similar to the Ack Vector
case, their value equals initially that of the sysctl, but at the end of
feature negotiation may be something different.

The old interface removed by this patch thus has been replaced by the newer
interface to dynamically query the currently loaded CCIDs.

Also removed are the constructors for the TX CCID and the RX CCID, since the
switch "rx <-> non-rx" is done by the handler in minisocks.c (and the handler
is the only place in the code where CCIDs are loaded).
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      0049bab5
    • W
      netdevice: Kill netdev->priv · b74ca3a8
      由 Wang Chen 提交于 
      This is the last shoot of this series.
After I removing all directly reference of netdev->priv, I am killing
"priv" of "struct net_device" and fixing relative comments/docs.

Anyone will not be allowed to reference netdev->priv directly.
If you want to reference the memory of private data, use netdev_priv()
instead.
If the private data is not allocted when alloc_netdev(), use
netdev->ml_priv to point that memory after you creating that private
data.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b74ca3a8
  13. 06 12月, 2008 1 次提交
  15. 05 12月, 2008 7 次提交