Change some data to unsigned int instead of integer when we compare.

Check LUT values in VIRTCHNL_OP_CONFIG_RSS_LUT handler.

Also enhance error/warning messages to print the real values of
I40E_MAX_VF_QUEUES, I40E_MAX_VF_VSI and I40E_DEFAULT_QUEUES_PER_VF
instead of plain text.

Refactor code to comply with 'check first then assign' policy.

Remove duplicate checks for VIRTCHNL_OP_CONFIG_RSS_KEY and
VIRTCHNL_OP_CONFIG_RSS_LUT opcodes in i40e_vc_process_vf_msg(). We have
the very same checks inside the handlers already.
Signed-off-by: NSergey Nemov <sergey.nemov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes it possible to log only AQ descriptors, without the
entire AQ message buffers being dumped too. It should greatly reduce
kernel log size in cases where a full AQ dump is not needed.
Selection is made by setting flags in hw->debug_mask.

Additionally, some debug messages that preceded an AQ dump have been
moved to I40E_DEBUG_AQ_COMMAND class, which seems more appropriate.
Signed-off-by: NDoug Dziggel <douglas.a.dziggel@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add bounds check for ch[] array.
Use ARRAY_SIZE() to ensure that idx is within the range.
Signed-off-by: NPiotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The counter variable in i40e_clean_tx_irq starts out negative and climbs
to 0. So it should not be defined as a u16. This was working by accident
due to the fact the u16 overflows and underflows predictably.

Replace the u16 with int, which is signed and can handle the negativity.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add veb array access boundary checks.
Ensure veb array index is smaller than I40E_MAX_VEB.
Signed-off-by: NPiotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch lets untrusted VF to create up to 16 VLANs.
It was implemented by increasing I40E_VC_MAX_VLAN_PER_VF up to 16.
Without this patch untrusted VF could create only up to 8 VLANs.
Signed-off-by: NPiotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds functions stubs to support EEE on/off.
Signed-off-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The PF driver state flag __I40E_VIRTCHNL_OP_PENDING needs to be
checked and set at the beginning of i40e_ndo_set_vf_mac. Otherwise,
if there are error conditions before it, the flag will be cleared
unexpectedly by this function to cause potential race conditions.
Hence move the check to the top of this function.
Signed-off-by: NLihong Yang <lihong.yang@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VF configuration returned in i40e_ndo_get_vf_config is
already stored by the PF. There is no dependency on any
specific state of the VF to return the configuration.
Drop the check against I40E_VF_STATE_INIT since it is not
needed.
Signed-off-by: NLihong Yang <lihong.yang@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove references to I40E_ETH_P_LLDP and use ETH_P_LLDP instead.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Added freeing the old allocation of vf->qvlist_info in function
i40e_config_iwarp_qvlist before overwriting it with
the new allocation.
Signed-off-by: NMartyna Szapar <martyna.szapar@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixed possible memory leak in i40e_vc_add_cloud_filter function:
cfilter is being allocated and in some error conditions
the function returns without freeing the memory.

Fix of integer truncation from u16 (type of queue_id value) to u8
when calling i40e_vc_isvalid_queue_id function.
Signed-off-by: NMartyna Szapar <martyna.szapar@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)

Notice that, in this case, variable size is not necessary, hence it
is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: N"Gustavo A. R. Silva" <gustavo@embeddedor.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The reason of this revert is unexpected issue found in NVM Update tool
during NVM image downgrade. The implementation is no longer needed
since the QV tools are already aware of new FW double ShadowRAM dump
mechanism.

This patch reverts ShadowRAM checksum calculation change introduced in
commit 9d12f0c4e436 ("i40e: Revert ShadowRAM checksum calculation change")
Signed-off-by: NMaciej Paczkowski <maciej.paczkowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Patch is adding missing input validation on VF message handling
by the PF to the functions with opcodes:
	VIRTCHNL_OP_CONFIG_VSI_QUEUES = 6
	VIRTCHNL_OP_CONFIG_IRQ_MAP = 7,
	VIRTCHNL_OP_DISABLE_QUEUES = 9,
	VIRTCHNL_OP_CONFIG_PROMISCUOUS_MODE = 14,
Signed-off-by: NMartyna Szapar <martyna.szapar@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

New device ids are created to support X710 backplane and SFP+ cards.

This patch adds in i40e driver support for 2.5GbaseT and 5GbaseT speed.
It's implemented by checking I40E_CAP_PHY_TYPE_2_5GBASE_T,
I40E_CAP_PHY_TYPE_5GBASE_T bits from f/w and setting corresponding bits
in ethtool link ksettings supported and advertising masks.
Signed-off-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: NAlice Michael <alice.michael@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In this patch fixed wrong truncation method from u16 to u8 during
validation.

It was changed by changing u8 to u32 parameter in method declaration
and arguments were changed to u32.
Signed-off-by: NGrzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Field num_vectors from struct virtchnl_iwarp_qvlist_info should not be
larger than num_msix_vectors_vf in the hw struct.  The iwarp uses the
same set of vectors as the LAN VF driver.
Signed-off-by: NSergey Nemov <sergey.nemov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the typo in I40E_CAP_PHY_TYPE mode link code.
It was fixed by changing 40000baseLR4_Full to 40000baseKR4_Full
Signed-off-by: NGrzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a bug where changing VLAN to 0 was not set until VF
restart.

Now we are setting pvid info to 0 when we have to change VLAN to 0.
Without this change when VF VLAN was changed to 0 nothing happened until
VF restart. For changing to VLAN different than 0 it worked correctly.
Signed-off-by: NGrzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

New device ids are created to support X710/XXV710 N3000 cards.
Signed-off-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a bug where the promiscuous mode was not being
kept when the VF switched to a new VLAN.
Now we are config two times a promiscuous mode when we switch VLAN.
Without this change when we change VF VLAN we still receive
all the packets from previous VLAN and only unicast from new VLAN.
Signed-off-by: NGrzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch introduces "recovery mode" to the i40e driver. It is
part of a new Any2Any idea of upgrading the firmware. In this
approach, it is required for the driver to have support for
"transition firmware", that is used for migrating from structured
to flat firmware image. In this new, very basic mode, i40e driver
must be able to handle particular IOCTL calls from the NVM Update
Tool and run a small set of AQ commands.

These additional AQ commands are part of the interface used by
the NVMUpdate tool.  The NVMUpdate tool contains all of the
necessary logic to reference these new AQ commands.  The end user
experience remains the same, they are using the NVMUpdate tool to
update the NVM contents.
Signed-off-by: NAlice Michael <alice.michael@intel.com>
Signed-off-by: NPiotr Marczak <piotr.marczak@intel.com>
Tested-by: NDon Buchholz <donald.buchholz@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Printing each devices PCI vendor and device ID has the advantage of
easily revealing what hardware we're dealing with exactly. It's no
longer necessary to match the PCI bus information to the lspci output.

Helps with bug reports where no lspci output is available.

Output before
i40e 0000:08:00.0: fw 6.1.49420 api 1.7 nvm 6.80 0x80003c64 1.2007.0
and after
i40e 0000:08:00.0: fw 6.1.49420 api 1.7 nvm 6.80 0x80003c64 1.2007.0 [8086:1572] [8086:0004]
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A refactor of the i40e_vc_config_promiscuous_mode_msg function moved
the check for un-trusted VF into another function. We have to lie to
an un-trusted VF that its request to set promiscuous mode is
successful even when it is not because we don't want the VF to find
out its trust status this way. With the refactor, we were running into
a case where even though we were not setting promiscuous mode for an
un-trusted VF, we still printed a misleading message that it was
successful.

This patch fixes that by ensuring that a success message is printed
on the host side only when the promiscuous mode change has been
successful.
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Just bumping the version number appropriately.
Signed-off-by: NAlice Michael <alice.michael@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The function i40e_validate_cloud_filter checks that the destination and
source port numbers are valid by attempting to ensure that the number is
non-zero and no larger than 0xFFFF. However, the types for the dst_port
and src_port variable are __be16 which by definition cannot be larger
than 0xFFFF

Since these values cannot be larger than 2 bytes, the check to see if
they exceed 0xFFFF is meaningless.

One might consider these checks as some sort of defensive coding, in
case the type was later changed. However, these checks also byte-swap
the value before comparison using be16_to_cpu, which will truncate the
values to 16bits anyways. Additionally, changing the type would require
updating the opcodes to support new data layout of these virtchnl
commands.

Remove the check to silence the -Wtype-limits warning that was added to
GCC 8.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This code implements driver code changes necessary for LLDP
Agent support. Modified i40e_aq_start_lldp() and
i40e_aq_stop_lldp() adding false parameter whether LLDP state
should be persistent across power cycles.
Signed-off-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add assignments for advertising 40GBase_LR4, 40GBase_CR4 and fibre
Signed-off-by: NAdam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to changes in FW the SW is required to perform double SR dump in
some cases.

Implementation adds two new steps to update nvm checksum function:
* recalculate checksum and check if checksum in NVM is correct
* if checksum in NVM is not correct then update it again
Signed-off-by: NMaciej Paczkowski <maciej.paczkowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

VF's attempt to delete vlan 0 when a port vlan is configured is harmless
in this case pf driver just does nothing.  If vf will try to remove
other vlans when a port vlan is configured it will still produce error
as before.
Signed-off-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

TX MDD events reported on the PF are the result of the
PF misconfiguring a descriptor and not because of "bad actions"
by anything else.  No need to reset now because if it
results in a Tx hang, the Tx hang check will take care of it.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes the driver behavior when detecting a VF MDD event.
It now disables the VF after one event, which indicates a hw detected
problem in the VF.  Before this change, the PF would allow a couple of
events before doing the reset.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update all users of eth_get_headlen to pass network device, fetch
network namespace from it and pass it down to the flow dissector.
This commit is a noop until administrator inserts BPF flow dissector
program.

Cc: Maxim Krasnyansky <maxk@qti.qualcomm.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NStanislav Fomichev <sdf@google.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

This patch changes an error code for an admin queue
head overrun to use I40E_ERR_ADMIN_QUEUE_FULL instead
of I40E_ERR_QUEUE_EMPTY.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the problem with the driver being able to add only 7
multicast MAC address filters instead of 16. The problem is fixed by
changing the maximum number of MAC address filters to 16+1+1 (two extra
are needed because the driver uses 1 for unicast MAC address and 1 for
broadcast).
Signed-off-by: NAdam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Defined the advertised link mode field for 40000baseSR4_Full for
use with ethtool.
Signed-off-by: NAdam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Added the API version in the error message for clarity.
Signed-off-by: NAdam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A new FW has been released, which uses API version 1.8.
Signed-off-by: NAdam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Removed misleading messages when untrusted VF tries to
add more addresses than NIC limit
Signed-off-by: NGrzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>