Add the register definition CH_BUSY_STA_SEC for reading the busy time
on the secondary channel in HT40 mode. Also update the comments about
channel busy/idle time registers to express the used unit.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make use of the IEEE80211_TX_RC_DUP_DATA flag to duplicate a
transmission with legacy rates to both 20Mhz channels if set.
Also update the related comment in rt2800.h to describe the
behavior of the BW_40 flag for legacy rates.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During rx, rt2x00lib calls rt2800pci_fill_rxdone to read the RX
descriptor. At that time the skb is already dma unmapped but no new skb
was dma mapped for this entry again. However, rt2800pci_fill_rxdone also
moves the hw rx queue index, marking this entry to be available for
reuse. Since no new skb was dma mapped and also the previous skb was
unmapped this might lead to strange hw behavior.

To fix this issue move the hw rx queue index increment to
rt2800pci_clear_entry where a new skb was already dma mapped and can be
safely used by the hw.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since HT protection is now configurable via mac80211 we don't need this
special case for PCI devices anymore. The HT protection config will be
overwritten as soon as mac80211 sends us a HT operation mode. Hence,
bring the HT MM40 protection config in sync with the other HT protection
registers and initialize it to no protection.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the HT operation mode when mac80211 sends it to us and set
the different HT protection modes and rates accordingly. For now
only use CTS-to-self with OFDM 24M or CCK 11M when protection is
required.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a check for dynamic SM PS mode in the STAs HT caps. Since a
value of 3 means "SM PS disabled" the previous check assumed in
that case that "dynamic SM PS" was enabled and as such prefixed
every MCS>7 frame with a unnecessary RTS/CTS exchange. Also,
the bit shift was done in the wrong direction.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch changes the way tx status reports are handled by rt2800pci.
Previously rt2800pci would sometimes lose tx status reports as the
TX_STA_FIFO register is a fifo of 16 entries that can overflow in case
we don't read it often/fast enough. Since interrupts are disabled in the
device during the execution of the interrupt thread it happend sometimes
under high network and CPU load that processing took too long and a few
tx status reports were dropped by the hw.

To fix this issue the TX_STA_FIFO register is read directly in the
interrupt handler and stored in a kfifo which is large enough to hold
all status reports of all used tx queues.

To process the status reports a new tasklet txstatus_tasklet is used.
Using the already used interrupt thread is not possible since we don't
want to disable the TX_FIFO_STATUS interrupt while processing them and
it is not possible to schedule the interrupt thread multiple times for
execution. A tasklet instead can be scheduled multiple times which
allows to leave the TX_FIFO_STATUS interrupt enabled while a previously
scheduled tasklet is still executing.

In short: All other interrupts are handled in the interrupt thread as
before. Only the TX_FIFO_STATUS interrupt is partly handled in the
interrupt handler and finished in the according tasklet.

One drawback of this patch is that it duplicates some code from
rt2800lib. However, that can be cleaned up in the future once the
rt2800usb and rt2800pci tx status handling converge more.

Using this patch on a Ralink RT3052 embedded board gives me a reliable
wireless connection even under high CPU and network load. I've
transferred several gigabytes without any queue lockups.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2800 devices use parts of the pariwise key table to store the beacon
frames for beacon 6 and 7. To not overwrite the beacon frame buffers
limit the number of entries we store in the pairwise key table to 222.

Also add some descriptive comments about this shared memory usage.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Source:
http://www.wikidevi.com/wiki/Intersil/p54/usb/windows

Cc: <stable@kernel.org>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Includes pkts/bytes that may have had errors, and includes
wireless headers when counting bytes.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds counters for tx and rx bytes, including any
errored packets as well as all wireless headers.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Acked-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Initialize the rate table for WDS interfaces, and
add cases to allow WDS packets to pass the xmit and receive
tests.
Signed-off-by: NBill Jordan <bjordan@rajant.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added a nl interface to set the peer bssid of a WDS interface.
Signed-off-by: NBill Jordan <bjordan@rajant.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable WDS for the ath9k driver.
Signed-off-by: NBill Jordan <bjordan@rajant.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On association to an AP, after receiving beacons, the beacon_crc value is set.
The beacon_crc value is not reset in disassociation, but the BSS data may be
expired at a later point. When associating again, it's possible that a
beacon for the AP is not received, resulting in the beacon_ies to remain NULL.

After association, further beacons will not update the beacon data, as the
crc value of the beacon has not changed, and the beacon_crc still holds a
value matching the beacon. The beacon_ies will remain forever null.

One of the results of this is that WLAN power save cannot be entered, the STA
will remain foreven in active mode.

Fix this by adding a validation flag for the beacon_crc, which is cleared on
association.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move ieee80211_scan_cancel() and all other related code to
ieee80211_restart_work() as ieee80211_restart_hw() is intended to be
callable from any context.

Fix a bug that RTNL lock is not taken during ieee80211_cancel_scan().

Take local->mtx before WARN(test_bit(SCAN_HW_SCANNING, &local->scanning)
to prevent the race condition with __ieee80211_start_scan() described
here: http://marc.info/?l=linux-wireless&m=128516716810537&w=2Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the ath9k debugging feature 'wiphy' the current channel used by the
station is incorrectly displayed.This is because the channels available
are sequentially mapped from numbers 0 to 37.This mapping cannot be
changed as the channel number is also used as an array index
          This fix solves the above problem by calculating the channel
number from center frequency.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The percal struct and bitmask for the initial DC calibration are not
used anywhere, so they can be removed.

Signed-off-by: Felix Fietkau <nbd@openwrt.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the regulatory code touches the channel array, it needs to be
copied for each device instance. That way the original channel array
can also be made const.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org [all]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add missing unlocking of the wiphy in set_channel,
and don't try to unlock a non-existing wiphy in
set_cqm.

Cc: stable@kernel.org [2.6.35+]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Support up to 4 virtual APs and as many virtual STA interfaces
as desired.

This patch is ported forward from a patch that Patrick McHardy
did for me against 2.6.31.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Acked-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The net/cfg80211.h header file isn't exported to
userspace, so there's no need for any kind of
__KERNEL__ protection in it. If it was exported,
everything else in it would need protection as
well, not just the logging stuff ...

Cc:Joe Perches <joe@perches.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable management frame transmission and subscribing
to management frames through nl80211 in both cfg80211
and mac80211. Also update a few places that I forgot
to update for P2P-client mode previously, and fix a
small bug with non-action frames in this API.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can start restarting firmware or RF kill switch can be turned on
during call to iwl_mac_add_interface(). That are normal working
conditions, so do not print call trace, just print simple message
instead.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The combined firmware ar9170.fw is preferred and supports all devices.
References to the older two-stage firmware are unnecessary.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some user space applications only want to display survey data for
the operating channel, however there is no API to get that yet.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

common->ani.noise_floor is now only used for a similar redundant debug
message similar to the one that was removed from ath9k_htc in an earlier
patch. Remove it from ath9k as well now.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is unused aside from a single redundant debug message
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The hardware rx-filter was essentially disabled, because
of a serve, yet unidentifiable problem with iwlagn.
Due to these circumstances the driver and mac80211 were
left with the job of filtering.

This is very unfortunate and has proven to be expensive
in terms of latency, memory and load.

Therefore the new 1.8.8.3 firmware introduces a flexible
filtering infrastructure which allows the driver to
offload some of the checks (FCS & PLCP crc check,
RA match, control frame filter, etc...) whenever possible.

Note:
This patch also includes all changes to the
shared headers files since the inclusion.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes an refcounting bug. Previously it
was possible to corrupt the per-device recv. filter
and monitor management counters when:
	iw dev wlanX set monitor [new flags]
was issued on an active monitor interface.
Acked-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Choose first available phyX name when creating phy devices.  This
means that reloading a wifi driver will not cause a change in the
name of it's phy device.

Also, allow users to rename a phy to any un-used name, including
phy%d.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6

For 6050 series device, change the supported API version
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since uCode is responsible for doing DC calibration, there's no need
to let init uCode to do initial DC calibration then send results
back to driver, then driver sends the results to runtime uCode.
Driver can simply tell runtime uCode to do DC calibration.

Actually, this patch does not disable DC calib for init uCode. It just
prevent driver from saving and sending the DC calib results (from init
ucode) to runtime uCode. The driver still uses 0xffffffff in
CALIB_CFG_CMD for init ucode.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

For 6050g2 devices driver needs to set a special bit to CSR register
so that uCode can do things correctly in calibration routines.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>