Add the hwspinlock device tree node for AM33xx family
of SoCs.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the hwspinlock device tree node for OMAP5 SoCs.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the hwspinlock device tree node for OMAP4 family
of SoCs.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Merge tag 'for_3.13_super_late/dts_signed' of git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt into omap-for-v3.13/dt

Add a lot of N900 nodes
Add OPP table to OMAP5/DRA7
Add support for Newflow NanoBone board

When the omap5-evm.dts file has been renamed to omap5-uevm.dts and the sEVM
support got deprecated in favor of uEVM (or Panda5) the content was not
validated.
Panda5 does not have support for digital microphones so remove the pinmux
section for it.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

When the omap5-evm.dts file has been renamed to omap5-uevm.dts and the sEVM
support got deprecated in favor of uEVM (or Panda5) the content was not
validated.
On uEVM the twl6040 reset GPIO is from gpio5_141 and not via gpio5_145, which
was the case in sEVM.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Enable support for the power button.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add support for LP5523 device.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

This patch adds support for Nokia N900 TLV320AIC3X chips.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add RX51_LCD_RESET_GPIO pin mux information to
display.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

This patch adds supports for Nokia N900 NAND memory.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add regulator names and voltage information to
the Nokia N900 DTS file.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The twl4030.dtsi is missing some regulators. This patch adds
the missing ones and orders the regulators alphabetically.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add support for LP5523 device.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add support for Nokia N900's vibrator.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add device tree node for the GPIO keys provided by the
N900 board. This is a simple conversion of the existing
board code.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add support for external SD card slot.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add UART support to Nokia N900.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Fix the bus speed of i2c bus 2 and 3.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add pin muxing support for the Nokia N900 i2c controllers.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add DT OPP table for DRA7xx family of devices. This data is decoded by
OF with of_init_opp_table() helper function.

The data is based on DRA75x, DRA74x Data Manual revision F (Sept 2013).

TODO: add OPP_HIGH after AVS-Class0 is functional
NOTE: The voltage and frequency values work well only on NOM samples
and it is mandatory to use ABB/AVS Class 0 support for all OPPs.

Clock nodes are pending clock node alignment.

[nm@ti.com: cleanups and rebase to latest]
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NJ Keerthy <j-keerthy@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add DT OPP table for OMAP54xx family of devices. This data is
decoded by OF with of_init_opp_table() helper function.

The data is based on OMAP543x ES2.0 DM Operating Condition Addendum
Version 0.6(April 2013)

NOTE: The voltage and frequency values work well only on NOM samples
and are supposed to work properly only with ABB/AVS for ALL OPPs.

TODO: Add SPEED BIN OPP after ABB and AVS support so the cpufreq works
on all samples seamlessly. Clock node is pending alignment for clock
dts conversion

[nm@ti.com: sync to latest and fixes]
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NJ Keerthy <j-keerthy@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

regulator smps123 supply from Palmas PMIC powers CPU0 on DRA7 EVM.

[nm@ti.com: rebase to latest]
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NJ Keerthy <j-keerthy@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

regulator smps123 supply from Palmas PMIC powers CPU0 on OMAP5uEVM.

Based on a patch by J Keerthy <j-keerthy@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Correct mcspi pin descriptions to match corresponding node name and
add chip select number to be consistent with OMAP5 TRM.
Signed-off-by: NEric Witcher <ewitcher@mindspring.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Control module is not usb specific.
Changes the label to usb_ctrl_mod.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

NanoBone Specification:
-----------------------
CPU:
  TI AM335x

Memory:
  256MB DDR3
  128MB NOR flash
  128KB FRAM

Ethernet:
  2 x 10/100 connected to SMSC LAN8710 PHY

USB:
  1 x USB2.0 Type A

I2C:
  2Kbit EEPROM (Microchip 24AA02)
  RTC (Maxim DS1338)
  GPIO Expander (Microchip MCP23017)

Expansion connector:
  6 x UART
  1 x MMC/SD
  1 x USB2.0
Signed-off-by: NMark Jackson <mpfj@newflow.co.uk>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Looks like omap3 is still relying on hwmod data for some basic
device tree information. Let's add the information to omap3.dtsi
so we can remove the related hwmod data once omap3 is DT only.
Acked-by: NBenoit Cousson <bcousson@baylibre.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Merge tag 'for_3.13_late/dts_signed' of git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt into omap-for-v3.13/dt

Add i2c aliases
Add McASP and audio support
Add reset/idle on init bindings for OMAP
Add more nodes for AM4272

Provide alias to allow ordering the i2c devices correctly.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Currently, on OMAP5, i2c1 and i2c5 defer probe due to pinctrl
dependencies. This changes the i2c ID each bus is registered with in
i2c-dev interface. As a result of this, many userspace tools break and
there is no consistent manner to fix the same if the i2c dev interface
have no consistent numbering.

Since this could happen for other OMAP derivatives, provide i2c alias
for all OMAP3+ SoCs to allow ordering the i2c devices correctly.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add mmc1 dt node to IGEP COM AQUILA board.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add nodes for McASP0 and McASP1 for AM43xx.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The generic PHY framewrok expects different properties than the
old USB PHY framework. Supply those properties.

Fixes USB OTG port on beagle after the Generic PHY framework was
merged in greg/usb-next. [1]

[1] - https://lkml.org/lkml/2013/9/27/581Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

AM335x EVM-SK have only support for audio playback (stereo jack on the
board) via tlv320aic3106 codec connected to McASP1.
Enable the support for audio playback on the board:
- McASP1 configuration
- tlv320aic3106 configuration
- Machine driver.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Adds sound, tlv320aic3106, mcasp1, and am335x_evm_audio_pin nodes.
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

This patch adds a second tuple to reg property. The new property tuple
describes the memory location for data port registers mapped trough
L3 bus on am33xx. The both property tuples are named accordingly in
the reg-names property.
Signed-off-by: NHebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add missing mcasp entries in the am33xx.dtsi include file.
Signed-off-by: NPantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

-> Adding pinmux for cpsw, i2c0.
-> Enabling the modules that are present in AM4372 EPOS EVM
These modules are tested on AM4372 EPOS EVM.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Populate nodes for l2-cache-controller, EDMA, mailbox,
mmc, sham.

Update as well DT properties for epwmss, aes, des.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>