The 8169 chip only generates MSI interrupts when all enabled event
sources are quiescent and one or more sources transition to active. If
not all of the active events are acknowledged, or a new event becomes
active while the existing ones are cleared in the handler, we will not
see a new interrupt.

The current interrupt handler masks off the Rx and Tx events once the
NAPI handler has been scheduled, which opens a race window in which we
can get another Rx or Tx event and never ACK'ing it, stopping all
activity until the link is reset (ifconfig down/up). Fix this by always
ACK'ing all event sources, and loop in the handler until we have all
sources quiescent.
Signed-off-by: NDavid Dillow <dave@thedillows.org>
Tested-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changeset ca17584b ("mac8390: update
to net_device_ops") broke mac8390 by adding 8390.o to the link. That
meant that lib8390.c was included twice, once in mac8390.c and once in
8390.c, subject to different macros. This patch reverts that by
avoiding the wrappers in 8390.c. They seem to be of no value since
COMPAT_NET_DEV_OPS is going away soon.

Tested with a Kinetics EtherPort card.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 0fd56bb5 ("gianfar:
Add support for skb recycling"), gianfar puts skbuffs that are in
the rx ring back onto the recycle list as-is in case there was a
receive error, but this breaks the following invariant: that all
skbuffs on the recycle list have skb->data = skb->head + NET_SKB_PAD.

The RXBUF_ALIGNMENT realignment done in gfar_new_skb() will be done
twice on skbuffs recycled in this way, causing there not to be enough
room in the skb anymore to receive a full packet, eventually leading
to an skb_over_panic from gfar_clean_rx_ring() -> skb_put().

Resetting the skb->data pointer to skb->head + NET_SKB_PAD before
putting the skb back onto the recycle list restores the mentioned
invariant, and should fix this issue.
Reported-by: NMichael Guntsche <mike@it-loops.com>
Tested-by: NMichael Guntsche <mike@it-loops.com>
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the i2400m is connected to a network, the host interface (USB)
cannot be suspended. For that to happen, the device has to have
negotiated with the basestation to put the link on IDLE state.

If the host tries to put the device in standby while it is connected
but not idle, the device resets, as the driver should not do that.

To avoid triggering that, when the USB susbsytem requires the driver
to autosuspend the device, the driver checks if the device is not yet
idle. If it is not, the request is rejected (will be retried again
later on after the autosuspend timeout). At some point the device will
enter idle and the request will succeed (unless of course, there is
network traffic, but at that point, there is no idle neither in the
link or the host interface).
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

Do not go beyond ARRAY_SIZE of intf->crypto_stats
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

enable iwl driver to support 5000 ucode having version 2 of API
Signed-off-by: NJay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"airo: airo_get_encode{,ext} potential buffer overflow" was actually a
no-op, due to an unrecognized type overflow in an assignment.  Oddly,
gcc only seems to tell me about it when using -Wextra...grrr...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the EEPROM contains weird values for the power levels we have to
fix the interpolation process.
Signed-off-by: NFabio Rossi <rossi.f@inwind.it>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Calling cancel_delayed_work() from inside
spin_lock_irqsave, introduces a potential deadlock.

As explained by Johannes Berg <johannes@sipsolutions.net>

A - lock
T - timer

phase                   CPU 1           CPU 2
---------------------------------------------

some place that calls
cancel_timer_sync()
(which is the | code)
                                        lock-irq(A)
|                                       "lock-irq"(T)
|                                       "unlock"(T)
|                                       wait(T)
                                        unlock(A)

timer softirq
                        "lock"(T)
                        run(T)
                        "unlock"(T)

irq handler
          lock(A)
          unlock(A)

Now all that again, interleaved, leading to deadlock:

                                        lock-irq(A)
                        "lock"(T)
                         run(T)
IRQ during or maybe
before run(T) -->        lock(A)
                                        "lock-irq"(T)
                                        wait(T)

We fix this by moving the call to cancel_delayed_work() into workqueue.
There are cases where the work may not actually be queued or running
at the time we are trying to cancel it, but cancel_delayed_work() is
able to deal with this.

Also cleanup iwl_set_mode related to this call. This function
(iwl_set_mode) is only called when bringing interface up and there will
thus not be any scanning done. No need to try to cancel scanning.

Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13224, which was also
reported at http://marc.info/?l=linux-wireless&m=124081921903223&w=2 .
Tested-by: NMiles Lane <miles.lane@gmail.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit e8f055f0 ("ath5k: Update reset code") subtly changed the
code that computes floating point values for the PHY3_TIMING register
such that the exponent is off by a decimal point, which can cause
problems with OFDM channel operation.

get_bitmask_order() actually returns the highest bit set plus one,
whereas the previous code wanted the highest bit set.  Instead, use
ilog2 which is what this code is really calculating.  Also check
coef_scaled to handle the (invalid) case where we need log2(0).
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR5K_PHY_PLL_40MHZ_5413 should not be ORed with AR5K_PHY_MODE_RAD_RF5112
for 5 GHz channels.

The incorrect PLL value breaks scanning in the countries where 5 GHz
channels are allowed.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FIFO1_DMA_ERR is set twice, the second should be FIFO2_DMA_ERR.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NRam Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After 2.6.29, PPC no more admits passing NULL to the dev parameter of
the DMA API. The result is a BUG followed by solid lock-up when the 
mv643xx_eth driver brings an interface up. The following patch makes 
the driver work on my Pegasos again; it is mostly a search and replace 
of NULL by mp->dev->dev.parent in dma allocation/freeing/mapping/unmapping
functions.
Signed-off-by: NGabriel Paubert <paubert@iram.es>
Acked-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the purposes of bonding is to allow for redundant links, and failover
correctly if the cable is pulled. If all the members of a bonded device have
no carrier present, the bonded device itself needs to report no carrier present
to user space so management tools (like routing daemons) can respond.

Bonding in 802.3ad mode does not work correctly for this because it incorrectly
chooses a link that is down as a possible aggregator.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mixing of normal and irq spinlocks results in the following lockdep messages
on bootup on IP32:

[...]
Sending DHCP requests .
======================================================
[ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ]
2.6.30-rc5-00164-g41baeef #30
------------------------------------------------------
swapper/1 [HC0[0]:SC0[1]:HE0:SE0] is trying to acquire:
 (&priv->meth_lock){+.+...}, at: [<ffffffff8026388c>] meth_tx+0x48/0x43c

and this task is already holding:
 (_xmit_ETHER#2){+.-...}, at: [<ffffffff802d3a00>] __qdisc_run+0x118/0x30c
which would create a new lock dependency:
 (_xmit_ETHER#2){+.-...} -> (&priv->meth_lock){+.+...}

but this new dependency connects a SOFTIRQ-irq-safe lock:
 (_xmit_ETHER#2){+.-...}
... which became SOFTIRQ-irq-safe at:
  [<ffffffff80061458>] __lock_acquire+0x784/0x1a14
  [<ffffffff800627e0>] lock_acquire+0xf8/0x150
  [<ffffffff800128d0>] _spin_lock+0x30/0x44
  [<ffffffff802d2b88>] dev_watchdog+0x70/0x398
  [<ffffffff800433b8>] run_timer_softirq+0x1a8/0x248
  [<ffffffff8003da5c>] __do_softirq+0xec/0x208
  [<ffffffff8003dbd8>] do_softirq+0x60/0xe4
  [<ffffffff8003dda0>] irq_exit+0x54/0x9c
  [<ffffffff80004420>] ret_from_irq+0x0/0x4
  [<ffffffff80004720>] r4k_wait+0x20/0x40
  [<ffffffff80015418>] cpu_idle+0x30/0x60
  [<ffffffff804cd934>] start_kernel+0x3ec/0x404

to a SOFTIRQ-irq-unsafe lock:
 (&priv->meth_lock){+.+...}
... which became SOFTIRQ-irq-unsafe at:
...  [<ffffffff800614f8>] __lock_acquire+0x824/0x1a14
  [<ffffffff800627e0>] lock_acquire+0xf8/0x150
  [<ffffffff800128d0>] _spin_lock+0x30/0x44
  [<ffffffff80263f20>] meth_reset+0x118/0x2d8
  [<ffffffff8026424c>] meth_open+0x28/0x140
  [<ffffffff802c1ae8>] dev_open+0xe0/0x18c
  [<ffffffff802c1268>] dev_change_flags+0xd8/0x1d4
  [<ffffffff804e7770>] ip_auto_config+0x1d4/0xf28
  [<ffffffff80012e68>] do_one_initcall+0x58/0x170
  [<ffffffff804cd190>] kernel_init+0x98/0x104
  [<ffffffff8001520c>] kernel_thread_helper+0x10/0x18

other info that might help us debug this:

2 locks held by swapper/1:
 #0:  (rcu_read_lock){.+.+..}, at: [<ffffffff802c0954>] dev_queue_xmit+0x1e0/0x4b0
 #1:  (_xmit_ETHER#2){+.-...}, at: [<ffffffff802d3a00>] __qdisc_run+0x118/0x30c

the SOFTIRQ-irq-safe lock's dependencies:
-> (_xmit_ETHER#2){+.-...} ops: 0 {
   HARDIRQ-ON-W at:
                        [<ffffffff800614d0>] __lock_acquire+0x7fc/0x1a14
                        [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                        [<ffffffff800128d0>] _spin_lock+0x30/0x44
                        [<ffffffff802d2b88>] dev_watchdog+0x70/0x398
                        [<ffffffff800433b8>] run_timer_softirq+0x1a8/0x248
                        [<ffffffff8003da5c>] __do_softirq+0xec/0x208
                        [<ffffffff8003dbd8>] do_softirq+0x60/0xe4
                        [<ffffffff8003dda0>] irq_exit+0x54/0x9c
                        [<ffffffff80004420>] ret_from_irq+0x0/0x4
                        [<ffffffff80004720>] r4k_wait+0x20/0x40
                        [<ffffffff80015418>] cpu_idle+0x30/0x60
                        [<ffffffff804cd934>] start_kernel+0x3ec/0x404
   IN-SOFTIRQ-W at:
                        [<ffffffff80061458>] __lock_acquire+0x784/0x1a14
                        [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                        [<ffffffff800128d0>] _spin_lock+0x30/0x44
                        [<ffffffff802d2b88>] dev_watchdog+0x70/0x398
                        [<ffffffff800433b8>] run_timer_softirq+0x1a8/0x248
                        [<ffffffff8003da5c>] __do_softirq+0xec/0x208
                        [<ffffffff8003dbd8>] do_softirq+0x60/0xe4
                        [<ffffffff8003dda0>] irq_exit+0x54/0x9c
                        [<ffffffff80004420>] ret_from_irq+0x0/0x4
                        [<ffffffff80004720>] r4k_wait+0x20/0x40
                        [<ffffffff80015418>] cpu_idle+0x30/0x60
                        [<ffffffff804cd934>] start_kernel+0x3ec/0x404
   INITIAL USE at:
                       [<ffffffff80061570>] __lock_acquire+0x89c/0x1a14
                       [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                       [<ffffffff800128d0>] _spin_lock+0x30/0x44
                       [<ffffffff802d2b88>] dev_watchdog+0x70/0x398
                       [<ffffffff800433b8>] run_timer_softirq+0x1a8/0x248
                       [<ffffffff8003da5c>] __do_softirq+0xec/0x208
                       [<ffffffff8003dbd8>] do_softirq+0x60/0xe4
                       [<ffffffff8003dda0>] irq_exit+0x54/0x9c
                       [<ffffffff80004420>] ret_from_irq+0x0/0x4
                       [<ffffffff80004720>] r4k_wait+0x20/0x40
                       [<ffffffff80015418>] cpu_idle+0x30/0x60
                       [<ffffffff804cd934>] start_kernel+0x3ec/0x404
 }
 ... key      at: [<ffffffff80cf93f0>] netdev_xmit_lock_key+0x8/0x1c8

the SOFTIRQ-irq-unsafe lock's dependencies:
-> (&priv->meth_lock){+.+...} ops: 0 {
   HARDIRQ-ON-W at:
                        [<ffffffff800614d0>] __lock_acquire+0x7fc/0x1a14
                        [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                        [<ffffffff800128d0>] _spin_lock+0x30/0x44
                        [<ffffffff80263f20>] meth_reset+0x118/0x2d8
                        [<ffffffff8026424c>] meth_open+0x28/0x140
                        [<ffffffff802c1ae8>] dev_open+0xe0/0x18c
                        [<ffffffff802c1268>] dev_change_flags+0xd8/0x1d4
                        [<ffffffff804e7770>] ip_auto_config+0x1d4/0xf28
                        [<ffffffff80012e68>] do_one_initcall+0x58/0x170
                        [<ffffffff804cd190>] kernel_init+0x98/0x104
                        [<ffffffff8001520c>] kernel_thread_helper+0x10/0x18
   SOFTIRQ-ON-W at:
                        [<ffffffff800614f8>] __lock_acquire+0x824/0x1a14
                        [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                        [<ffffffff800128d0>] _spin_lock+0x30/0x44
                        [<ffffffff80263f20>] meth_reset+0x118/0x2d8
                        [<ffffffff8026424c>] meth_open+0x28/0x140
                        [<ffffffff802c1ae8>] dev_open+0xe0/0x18c
                        [<ffffffff802c1268>] dev_change_flags+0xd8/0x1d4
                        [<ffffffff804e7770>] ip_auto_config+0x1d4/0xf28
                        [<ffffffff80012e68>] do_one_initcall+0x58/0x170
                        [<ffffffff804cd190>] kernel_init+0x98/0x104
                        [<ffffffff8001520c>] kernel_thread_helper+0x10/0x18
   INITIAL USE at:
                       [<ffffffff80061570>] __lock_acquire+0x89c/0x1a14
                       [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                       [<ffffffff800128d0>] _spin_lock+0x30/0x44
                       [<ffffffff80263f20>] meth_reset+0x118/0x2d8
                       [<ffffffff8026424c>] meth_open+0x28/0x140
                       [<ffffffff802c1ae8>] dev_open+0xe0/0x18c
                       [<ffffffff802c1268>] dev_change_flags+0xd8/0x1d4
                       [<ffffffff804e7770>] ip_auto_config+0x1d4/0xf28
                       [<ffffffff80012e68>] do_one_initcall+0x58/0x170
                       [<ffffffff804cd190>] kernel_init+0x98/0x104
                       [<ffffffff8001520c>] kernel_thread_helper+0x10/0x18
 }
 ... key      at: [<ffffffff80cf6ce8>] __key.32424+0x0/0x8

stack backtrace:
Call Trace:
[<ffffffff8000ed0c>] dump_stack+0x8/0x34
[<ffffffff80060b74>] check_usage+0x470/0x4a0
[<ffffffff80060c34>] check_irq_usage+0x90/0x130
[<ffffffff80061f78>] __lock_acquire+0x12a4/0x1a14
[<ffffffff800627e0>] lock_acquire+0xf8/0x150
[<ffffffff80012a0c>] _spin_lock_irqsave+0x60/0x84
[<ffffffff8026388c>] meth_tx+0x48/0x43c
[<ffffffff802d3a38>] __qdisc_run+0x150/0x30c
[<ffffffff802c0aa8>] dev_queue_xmit+0x334/0x4b0
[<ffffffff804e7e6c>] ip_auto_config+0x8d0/0xf28
[<ffffffff80012e68>] do_one_initcall+0x58/0x170
[<ffffffff804cd190>] kernel_init+0x98/0x104
[<ffffffff8001520c>] kernel_thread_helper+0x10/0x18

..... timed out!
IP-Config: Retrying forever (NFS root)...
Sending DHCP requests ., OK
[...]

Fixed by converting all locks to irq locks.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Tested-by: NAndrew Randrianasulu <randrik_a@yahoo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Napi structures are being created each time we open a port, but when
the port is closed the napi structure is only disabled but not removed.
This bug caused hang while removing the driver.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the i2400m receives data and the device indicates there has to be
reordering, we keep an sliding window implementation to sort the
packets before sending them to the network stack.

One of the "operations" that the device indicates is "queue a packet
and update the window start". When the queue is empty, this is
equivalent to "deliver the packet and update the window start".

That case was optimized in i2400m_roq_queue_update_ws() so that we
would not pointlessly queue and dequeue a packet. However, when the
optimization was active, it wasn't updating the window start. That
caused the reorder management code to get confused later on with what
seemed to be wrong reorder requests from the device.

Thus the fix implemented is to do the right thing and update the
window start in both cases, when the queue is empty (and the
optimization is done) and when not.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

Remove the return after the goto.  We want the goto because it frees
memory as well as returning err.

Found by smatch (http://repo.or.cz/w/smatch.git).
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add device ids for 2x2 devices. Also fix antenna usage because these devices use
antennas A and B, not B and C.
Signed-off-by: NJay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes a non-theoretical race condition when transmitting and
receiving frames during a scan.  If the channel or operating band
changes while processing status descriptors in the tasklets, ath5k
will incorrectly use the new channel and band when reporting the
rates, even if the frame was actually sent on a previous channel.

Typically this will manifest as a beacon found on an incorrect
frequency and/or a warning in the driver while scanning:

[ 4773.891944] cfg80211: Found new beacon on frequency: 5805 MHz (Ch 161) on phy0
[ 4785.461125] ------------[ cut here ]------------
[ 4785.461135] WARNING: at drivers/net/wireless/ath/ath5k/base.c:1141 ath5k_tasklet_rx+0x2ff/0x577 [ath5k]()
[ 4785.461143] Hardware name: MacBook1,1
[ 4785.461148] invalid hw_rix: 1b
[ 4785.461152] Modules linked in: fuse i915 drm af_packet acpi_cpufreq binfmt_misc dm_mirror dm_region_hash dm_log dm_multipath dm_mod arc4 ecb snd_hda_codec_idt snd_hda_intel snd_hda_codec snd_seq_dummy snd_seq_oss snd_seq_midi_event ath5k snd_seq hid_apple usbhid snd_seq_device mac80211 appletouch snd_pcm_oss sky2 ohci1394 snd_mixer_oss ath ieee1394 snd_pcm bitrev snd_timer cfg80211 crc32 snd snd_page_alloc button processor ac ehci_hcd joydev uhci_hcd sg battery thermal sr_mod cdrom applesmc evdev input_polldev unix [last unloaded: microcode]
[ 4785.461296] Pid: 0, comm: swapper Tainted: G        W  2.6.30-rc3-wl #112
[ 4785.461302] Call Trace:
[ 4785.461316]  [<c012590f>] warn_slowpath+0x76/0xa5
[ 4785.461331]  [<c0219839>] ? debug_dma_unmap_page+0x5a/0x62
[ 4785.461357]  [<f9982f88>] ath5k_tasklet_rx+0x2ff/0x577 [ath5k]
[ 4785.461371]  [<c01446f7>] ? trace_hardirqs_off+0xb/0xd
[ 4785.461381]  [<c0129928>] ? __tasklet_schedule+0x6e/0x7c
[ 4785.461392]  [<c0129b02>] tasklet_action+0x92/0xe5
[ 4785.461402]  [<c0129f91>] __do_softirq+0xb1/0x182
[ 4785.461411]  [<c012a092>] do_softirq+0x30/0x48
[ 4785.461428]  [<c012a20a>] irq_exit+0x3d/0x74
[ 4785.461435]  [<c035a0de>] do_IRQ+0x76/0x8c
[ 4785.461440]  [<c010312e>] common_interrupt+0x2e/0x34
[ 4785.461445]  [<c014007b>] ? timer_list_show+0x1ab/0x939
[ 4785.461457]  [<f85fd25c>] ? acpi_idle_enter_bm+0x27c/0x2b9 [processor]
[ 4785.461463]  [<c02d1ed6>] cpuidle_idle_call+0x6a/0x9c
[ 4785.461468]  [<c0101cc8>] cpu_idle+0x53/0x87
[ 4785.461473]  [<c0346584>] rest_init+0x6c/0x6e
[ 4785.461479]  [<c04df74d>] start_kernel+0x286/0x28b
[ 4785.461484]  [<c04df037>] __init_begin+0x37/0x3c
[ 4785.461487] ---[ end trace aaf8496ba3679dfb ]---
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Feeding the return code of get_wep_key directly to the length parameter
of memcpy is a bad idea since it could be -1...
Reported-by: NEugene Teo <eugeneteo@kernel.sg>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If module initialisation failed (e.g. because the bonding sysfs entry
cannot be created), kernel panics:
 IP: [<ffffffff8024910a>] destroy_workqueue+0x2d/0x146
Call Trace:
 [<ffffffff808268c4>] bond_destructor+0x28/0x78
 [<ffffffff80b64471>] netdev_run_todo+0x231/0x25a
 [<ffffffff80b6dbcd>] rtnl_unlock+0x9/0xb
 [<ffffffff81567907>] bonding_init+0x83e/0x84a

Remove the calls to bond_work_cancel_all() and destroy_workqueue();
both are also called/scheduled via bond_free_all().

bond_destroy_sysfs is unecessary because the sysfs entry has
not been created in the error case.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>

ENOSYS makes modutils complain about missing kernel module support.
Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>

Add barrier() to bnx2_get_hw_{tx|rx}_cons() to fix this issue:

http://bugzilla.kernel.org/show_bug.cgi?id=12698

This issue was reported by multiple i386 users.  Without barrier(),
the compiled code looks like the following where %eax contains the
address of the tx_cons or rx_cons in the DMA status block.  The
status block contents can change between the cmpb and the movzwl
instruction.  The driver would crash if the value was not 0xff during
the cmpb instruction, but changed to 0xff during the movzwl
instruction.

6828:	80 38 ff             	cmpb   $0xff,(%eax)
682b:	0f b7 10             	movzwl (%eax),%edx

With the added barrier(), the compiled code now looks correct:

683d:	0f b7 10             	movzwl (%eax),%edx
6840:	0f b6 c2             	movzbl %dl,%eax
6843:	3d ff 00 00 00       	cmp    $0xff,%eax

Thanks to Pascal de Bruijn <pmjdebruijn@pcode.nl> for reporting the
problem and Holger Noefer <hnoefer@pironet-ndh.com> for patiently
testing test patches for us.

Also updated version to 2.0.1.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The setup_rctl call was making a call into the ring structure after it had
been freed.  This was causing a panic on shutdown.  This call wasn't
necessary since it is possible to get the needed index from
adapter->vfs_allocated_count.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

a recent fix to e1000 (commit 15b2bee2) caused KVM/QEMU/VMware based
virtualized e1000 interfaces to begin failing when resetting.

This is because the driver in a virtual environment doesn't
get to run instructions *AT ALL* when an interrupt is asserted.
The interrupt code runs immediately and this recent bug fix
allows an interrupt to be possible when the interrupt handler
will reject it (due to the new code), when being called from
any path in the driver that holds the E1000_RESETTING flag.

the driver should use the __E1000_DOWN flag instead of the
__E1000_RESETTING flag to prevent interrupt execution
while reconfiguring the hardware.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix locking issue in alb MAC address management; removed
incorrect locking and replaced with correct locking.  This bug was
introduced in commit 059fe7a5
("bonding: Convert locks to _bh, rework alb locking for new locking")

	Bug reported by Paul Smith <paul@mad-scientist.net>, who also
tested the fix.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to be symmetrical in what is done when key is set and cleared.
This is important wrt the key flags as they are used during key
clearing and if they are not set when the key is set the key cannot be
cleared completely.

This addresses the many occurences of the WARN found in
iwl_set_tkip_dynamic_key_info() and tracked in
http://www.kerneloops.org/searchweek.php?search=iwl_set_dynamic_key

If calling iwl_set_tkip_dynamic_key_info()/iwl_remove_dynamic_key()
pair a few times in a row will cause that we run out of key space.
This is because the index stored in the key flags is used by
iwl_remove_dynamic_key() to decide if it should remove the key.
Unfortunately the key flags, and hence the key index is currently only
set at the time the key is written to the device (in
iwl_update_tkip_key()) and _not_ in iwl_set_tkip_dynamic_key_info().
Fix this by setting flags in iwl_set_tkip_dynamic_key_info().
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It does not make sense to apply EXPORT_SYMBOL to a static symbol.  Fixes
this build error:

drivers/net/wireless/iwlwifi/iwl3945-base.c:1697: error: __ksymtab_iwl3945_rx_queue_reset causes a section type conflict
Signed-off-by: NAndreas Schwab <schwab@linux-m68k.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This introduces a CDC Ethernet Emulation Model (EEM) host side
driver to support USB EEM devices.

EEM is different from the Ethernet Control Model (ECM) currently
supported by the "CDC Ethernet" driver.  One key difference is
that it doesn't require of USB interface alternate settings to
manage interface state; some maldesigned hardware can't handle
that part of USB.  It also avoids a separate USB interface for
control and status updates.

[ dbrownell@users.sourceforge.net: fix skb leaks, add rx packet
checks, improve fault handling, EEM conformance updates, cleanup ]
Signed-off-by: NOmar Laazimani <omar.oberthur@gmail.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes an invalid pointer access in case the receive queue
holds no pointer to the next skb when the queue is empty.
Signed-off-by: NHannes Hering <hering2@de.ibm.com>
Signed-off-by: NJan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Doing it in reverse order causes uevent to be sent before
we have a MAC address, which confuses udev.
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlex Williamson <alex.williamson@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were avoiding calling sg_init* on scatterlists passed
into virtnet_send_command to prevent extraneous end markers.
This caused build warnings for uninitialized variables.
Cleanup the code to create proper scatterlists.
Signed-off-by: NAlex Williamson <alex.williamson@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes the cleanup in bond_create nicer :) Also now the forgotten
free_netdev is called.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LAN9512 and LAN9514 are USB hubs with an integrated 10/100 ethernet
controller.  Logically this looks like an ethernet controller (similar
to LAN9500) permanently attached to one of the hub's downstream ports.

This patch adds the usb device id of the new ethernet controller to the
smsc95xx driver.  This id is the same in both new devices.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SMSC LAN9500 has dual purpose GPIO/LED pins, and by default at power-on
these are configured as GPIOs.  This means that if LEDs are fitted they
won't ever light.

This patch sets them to be LED outputs for speed, duplex and
link/activity.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>