Keep a pointer to associated me client in the host client object to
eliminate me client searches. Check if the me client is active in the
firmware by checking if its is linked on the me clients list
Add accessors for the me client properties from host client.
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Simplify connect state machine by changing the logic around
Connection request in progress - only check if we have a callback in
relevant queue.
Extract common code into mei_cl_send_connect() function
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Split disconnected state into two parts first reception disconnect
response from the firmware and second actually setting of disconnected
state.  Book keeping data are needed for processing and after firmware
disconnected the client and are cleaned when setting the disconnected
state in mei_cl_set_disconneted() function.
Add mei_cl_send_disconnect to reduce code duplication.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

HW has to be in known state before the initialisation
sequence is started. The polling step for settling aliveness
was set to 200ms while in practise this can be done in up to 30msecs.

Cc: <stable@vger.kernel.org> #3.18+
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NBarak Yoresh <barak.yoresh@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver manages Qualcomm CoreSight Replicator device, which
resides on the AMBA bus. Replicator has been made programmable to
allow software to turn of the replicator branch to sink that is not
being used. This avoids trace traffic to the unused/non-current sink
from causing back pressure that results in overflows at the source.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NIvan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

fixes obvious typo in of_coresight.c
%s/non-configuable/non-configurable
Signed-off-by: NPankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Put in a blurb in the device tree bindings indicating that
coresight blocks may have an optional ATCLK.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As can be seen from the datasheet of the CoreSight
Components, DDI0314 table A-4 the funnel has a clock signal
apart from the AHB interconnect ("amba_pclk", that we're
already handling) called ATCLK, ARM Trace Clock, that SoC
implementers may provide from an entirely different clock
source. So to model this correctly create an optional
path for handling ATCLK alongside the PCLK so we don't
break old platforms that only define PCLK ("amba_pclk") but
still makes it possible for SoCs that have both clock signals
(such as the DB8500) to fetch and prepare/enable/disable/
unprepare both clocks.

The ATCLK is enabled and disabled using the runtime PM
callbacks. As the replicator is a platform device, the
code is a bit different from the other CoreSight components
and the bus core does not activate runtime PM by default,
so we need a few extra calls.
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As can be seen from the datasheet of the CoreSight
Components, DDI0314 table A-6 the funnel has a clock signal
apart from the AHB interconnect ("amba_pclk", that we're
already handling) called ATCLK, ARM Trace Clock, that SoC
implementers may provide from an entirely different clock
source. So to model this correctly create an optional
path for handling ATCLK alongside the PCLK so we don't
break old platforms that only define PCLK ("amba_pclk") but
still makes it possible for SoCs that have both clock signals
(such as the DB8500) to fetch and prepare/enable/disable/
unprepare both clocks.

The ATCLK is enabled and disabled using the runtime PM
callbacks.
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As can be seen from the datasheet of the CoreSight
Components, DDI0314 table A-8 the ETB has a clock signal
apart from the AHB interconnect ("amba_pclk", that we're
already handling) called ATCLK, ARM Trace Clock, that SoC
implementers may provide from an entirely different clock
source. So to model this correctly create an optional
path for handling ATCLK alongside the PCLK so we don't
break old platforms that only define PCLK ("amba_pclk") but
still makes it possible for SoCs that have both clock signals
(such as the DB8500) to fetch and prepare/enable/disable/
unprepare both clocks.

The ATCLK is enabled and disabled using the runtime PM
callbacks.
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As can be seen from the datasheet of the CoreSight
Components, DDI0314H page A-19 the TPIU has a clock signal
apart from the AHB interconnect ("amba_pclk", that we're
already handling) called ATCLK, ARM Trace Clock, that SoC
implementers may provide from an entirely different clock
source. So to model this correctly create an optional
path for handling ATCLK alongside the PCLK so we don't
break old platforms that only define PCLK ("amba_pclk") but
still makes it possible for SoCs that have both clock signals
(such as the DB8500) to fetch and prepare/enable/disable/
unprepare both clocks in conjunction.

The ATCLK is enabled and disabled using the runtime PM
callbacks.
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As can be seen from the datasheet of the CoreSight
Components, DDI0401C A.1.1 the ETM has a clock signal
apart from the AHB interconnect ("amba_pclk", that we're
already handling) called ATCLK, ARM Trace Clock, that SoC
implementers may provide from an entirely different clock
source. So to model this correctly create an optional
path for handling ATCLK alongside the PCLK so we don't
break old platforms that only define PCLK ("amba_pclk") but
still makes it possible for SoCs that have both clock signals
(such as the DB8500) to fetch and prepare/enable/disable/
unprepare both clocks.

The ATCLK is enabled and disabled using the runtime PM
callbacks.
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This uses runtime PM to manage the PCLK ("amba_pclk") instead
of screwing around with the framework by going in and taking
a copy from the amba device. The amba bus core will unprepare
and disable the clock when the device is unused when
CONFIG_PM is selected, else the clock will be always on.

Prior to this patch, as the AMBA primecell bus code enables
the PCLK, it would be left on after probe as
the clk_prepare_enable() and clk_disable_unprepare() was
called and thus just increase and decreas the refcount by
one, without it reaching zero and actually disabling the
clock. Now the runtime PM callbacks will make sure the PCLK
is properly disabled after probe.
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This uses runtime PM to manage the PCLK ("amba_pclk") instead
of screwing around with the framework by going in and taking
a copy from the amba device. The amba bus core will unprepare
and disable the clock when the device is unused when
CONFIG_PM is selected, else the clock will be always on.

Prior to this patch, as the AMBA primecell bus code enables
the PCLK, it would be left on after probe as
clk_disable_unprepare() was not called. Now the runtime PM
callbacks will make sure the PCLK is properly disabled
after probe.
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This uses runtime PM to manage the PCLK ("amba_pclk") instead
of screwing around with the framework by going in and taking
a copy from the amba device. The amba bus core will unprepare
and disable the clock when the device is unused when
CONFIG_PM is selected, else the clock will be always on.

Prior to this patch, as the AMBA primecell bus code enables
the PCLK, it would be left on after probe as
the clk_prepare_enable() and clk_disable_unprepare() was
called and thus just increase and decreas the refcount by
one, without it reaching zero and actually disabling the
clock. Now the runtime PM callbacks will make sure the PCLK
is properly disabled after probe.
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This uses runtime PM to manage the PCLK ("amba_pclk") instead
of screwing around with the framework by going in and taking
a copy from the amba device. The amba bus core will unprepare
and disable the clock when the device is unused when
CONFIG_PM is selected, else the clock will be always on.

Prior to this patch, as the AMBA primecell bus code enables
the PCLK, it would be left on after probe as
the clk_prepare_enable() and clk_disable_unprepare() was
called and thus just increase and decreas the refcount by
one, without it reaching zero and actually disabling the
clock. Now the runtime PM callbacks will make sure the PCLK
is properly disabled after probe.
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This uses runtime PM to manage the PCLK ("amba_pclk") instead
of screwing around with the framework by going in and taking
a copy from the amba device. The amba bus core will unprepare
and disable the clock when the device is unused when
CONFIG_PM is selected, else the clock will be always on.

Prior to this patch, as the AMBA primecell bus code enables
the PCLK, it would be left on after probe as
the clk_prepare_enable() and clk_disable_unprepare() was
called and thus just increase and decreas the refcount by
one, without it reaching zero and actually disabling the
clock. Now the runtime PM callbacks will make sure the PCLK
is properly disabled after probe.
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Ux500 has a PrimeCell version 4B instead of the 3B as
supported by the driver, extend the match table to cover
this version.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Helpfully report a bit more about the hardware found in the
silicon when matching the AMBA device IDs by using the associated
.data pointer in the AMBA match.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Using function "module_amba_driver()" makes the code simpler by
eliminating boilerplate code.

Wei Yongjun sent out a set of patches addressing those in all the
coresight driver but missed ETMv3.
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ETM ID registers contain valuable information about the capabilities
of the implementation and are very useful when configuring the device for
various trace scenarios.
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Having access to the ETMv4 management registers is very useful as they
give meaningful information on how the IP block has been configured at
synthesis time.
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding sysfs entries to access and configure specifics about the
virtual machine ID comparator functions.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding sysfs entries to access and configure specifics about the
context ID comparator functions.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding sysfs entries to control the selection of the resources the
trace unit will use as triggers to perform a trace run.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding sysfs entries related to the counter functionality, more
specifically to set, control and reload the counters.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding sysfs entries to access the sequencers related registers,
more specifically the sequencer state, the sequencer state
transition and the sequencer reset control registers.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding sysfs entries to control the various mode the address comparator
registers can enact, i.e, start/top, single, and range.  Also supplementing
with address comparator types configuration registers access, mandatory
to complete the configuration of the comparator functions.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding sysfs entries to control the ViewInst register's event
selector along with secure and non-secure exception level
instruction tracing.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding sysfs entries to configure:
. global timestamp.
. how often trace synchronisation occur.
. the threashold value for cycle counting.
. branch and broadcasting regions.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding sysfs entries to:
. set the tracing entity with default values.
. set various mode associated to the tracing entity.
. select the processing entity the tracing entity relates to.
. select various events of interest.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Tracers can be configured with various options at synthesis
time and knowing what resources are available is important for
SW configuration purposes.

As such adding RO sysfs entries for characteristics related to the
tracer implementation.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver manages the CoreSight ETMv4 (Embedded Trace Macrocell) IP block
to support HW assisted tracing on ARMv7 and ARMv8 architectures.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NKaixu Xia <xiakaixu@huawei.com>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We attempt to sanity check the buffer depth reported by the hardware by
making sure it is not less than zero however this check will never be true
since the buffer depth is stored in an unsigned integer. Instead change
the check to look for the top bit being set which was the intention.
Signed-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When we initialise the ETB driver we attempt to allocate a buffer suitable
for storing the data buffered in the hardware based on sizing information
reported by the hardware. Unfortunately if the hardware is not properly
configured (for example if power domains are not set up correctly) then we
may read back a nonsensically large value and therefore the allocation will
be too big to succeed. Print an error message showing the amount of memory
we tried to allocate if the buffer allocation fails to help users diagnose
such problems.

Normally it is bad practice to print an error message on memory allocation
failures since there are verbose core messages reported for this but in
this case where the allocation size might be incorrect it is a useful hint.
Signed-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Two watchdog changes that came through different trees had a non
conflicting conflict, that is, one changed the semantics of a variable
but no actual code conflict happened. So the merge appeared fine, but
the resulting code did not behave as expected.

Commit 195daf66 ("watchdog: enable the new user interface of the
watchdog mechanism") changes the semantics of watchdog_user_enabled,
which thereafter is only used by the functions introduced by
b3738d29 ("watchdog: Add watchdog enable/disable all functions").

There further appears to be a distinct lack of serialization between
setting and using watchdog_enabled, so perhaps we should wrap the
{en,dis}able_all() things in watchdog_proc_mutex.

This patch fixes a s2r failure reported by Michal; which I cannot
readily explain. But this does make the code internally consistent
again.
Reported-and-tested-by: NMichal Hocko <mhocko@suse.cz>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull MTD fixes from Brian Norris:
 "Two MTD fixes for 4.1:

   - readtest: the signal-handling code was clobbering the error codes
     we should be handling/reporting in this test, rendering it useless.
     Noticed by Coverity.

   - the common SPI NOR flash DT binding (merged for 4.1-rc1) is being
     revised, so let's change that before 4.1 is minted"

* tag 'for-linus-20150516' of git://git.infradead.org/linux-mtd:
  Documentation: dt: mtd: replace "nor-jedec" binding with "jedec, spi-nor"
  mtd: readtest: don't clobber error reports

Pull USB fixes from Greg KH:
 "Here are some USB fixes and new device ids for 4.1-rc4.

  All are pretty minor, and have been in linux-next successfully"

* tag 'usb-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb-storage: Add NO_WP_DETECT quirk for Lacie 059f:0651 devices
  Added another USB product ID for ELAN touchscreen quirks.
  xhci: gracefully handle xhci_irq dead device
  xhci: Solve full event ring by increasing TRBS_PER_SEGMENT to 256
  xhci: fix isoc endpoint dequeue from advancing too far on transaction error
  usb: chipidea: debug: avoid out of bound read
  USB: visor: Match I330 phone more precisely
  USB: pl2303: Remove support for Samsung I330
  USB: cp210x: add ID for KCF Technologies PRN device
  usb: gadget: remove incorrect __init/__exit annotations
  usb: phy: isp1301: work around tps65010 dependency
  usb: gadget: serial: fix re-ordering of tx data
  usb: gadget: hid: Fix static variable usage
  usb: gadget: configfs: Fix interfaces array NULL-termination
  usb: gadget: xilinx: fix devm_ioremap_resource() check
  usb: dwc3: dwc3-omap: correct the register macros

Pull tty/serial fixes from Greg KH:
 "Here's some TTY and serial driver fixes for reported issues.

  All of these have been in linux-next successfully"

* tag 'tty-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  pty: Fix input race when closing
  tty/n_gsm.c: fix a memory leak when gsmtty is removed
  Revert "serial/amba-pl011: Leave the TX IRQ alone when the UART is not open"
  serial: omap: Fix error handling in probe
  earlycon: Revert log warnings