When connected to a QoS/WMM AP, mac80211 should use a QoS NDP
for probing it, instead of a regular non-QoS one, fix this.

Change all the drivers to *not* allow QoS NDP for now, even
though it looks like most of them should be OK with that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Commit 86dabda4 ("net: thunderbolt: Clear finished Tx frame bus
address in tbnet_tx_callback()") fixed a DMA-API violation where the
driver called dma_unmap_page() in tbnet_free_buffers() for a bus address
that might already be unmapped. The fix was to zero out the bus address
of a frame in tbnet_tx_callback().

However, as pointed out by David Miller, zero might well be valid
mapping (at least in theory) so it is not good idea to use it here.

It turns out that we don't need the whole map/unmap dance for Tx buffers
at all. Instead we can map the buffers when they are initially allocated
and unmap them when the interface is brought down. In between we just
DMA sync the buffers for the CPU or device as needed.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't offload IP header checksum to NIC.

This fixes a previous patch which enabled checksum offloading
for both IPv4 and IPv6 packets.  So L3 checksum offload was
getting enabled for IPv6 pkts.  And HW is dropping these pkts
as it assumes the pkt is IPv4 when IP csum offload is set
in the SQ descriptor.

Fixes:  3a9024f5 ("net: thunderx: Enable TSO and checksum offloads for ipv6")
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@auriga.com>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function pci_unmap_page is obsolete. So it is replaced with
the function dma_unmap_page.

CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: NZhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the function ipvlan_get_L3_hdr, current codes use pskb_may_pull to
make sure the skb header has enough linear room for ipv6 header. But it
would use the latter memory directly without linear check when it is icmp.
So it still may access the unepxected memory in ipvlan_addr_lookup.

Now invoke the pskb_may_pull again if it is ipv6 icmp.
Signed-off-by: NGao Feng <gfree.wind@vip.163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the function ipvlan_get_L3_hdr, current codes use pskb_may_pull to
make sure the skb header has enough linear room for arp header. But it
would access the arp payload in func ipvlan_addr_lookup. So it still may
access the unepxected memory.

Now use arp_hdr_len(port->dev) instead of the arp header as the param.
Signed-off-by: NGao Feng <gfree.wind@vip.163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stefano pointed that configure or show UDP_ZERO_CSUM6_RX/TX info doesn't
make sense if we haven't enabled CONFIG_IPV6. Fix it by adding
if IS_ENABLED(CONFIG_IPV6) check.

Fixes: abe492b4 ("geneve: UDP checksum configuration via netlink")
Fixes: fd7eafd0 ("geneve: fix fill_info when link down")
Signed-off-by: NHangbin Liu <liuhangbin@gmail.com>
Reviewed-by: NStefano Brivio <sbrivio@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PHY on BCM7278 has an additional bit that needs to be cleared:
IDDQ_GLOBAL_PWR, without doing this, the PHY remains stuck in reset out
of suspend/resume cycles.

Fixes: 0fe99338 ("net: dsa: bcm_sf2: Add support for BCM7278 integrated switch")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tuntap and similar devices can inject GSO packets. Accept type
VIRTIO_NET_HDR_GSO_UDP, even though not generating UFO natively.

Processes are expected to use feature negotiation such as TUNSETOFFLOAD
to detect supported offload types and refrain from injecting other
packets. This process breaks down with live migration: guest kernels
do not renegotiate flags, so destination hosts need to expose all
features that the source host does.

Partially revert the UFO removal from 182e0b6b~1..d9d30adf.
This patch introduces nearly(*) no new code to simplify verification.
It brings back verbatim tuntap UFO negotiation, VIRTIO_NET_HDR_GSO_UDP
insertion and software UFO segmentation.

It does not reinstate protocol stack support, hardware offload
(NETIF_F_UFO), SKB_GSO_UDP tunneling in SKB_GSO_SOFTWARE or reception
of VIRTIO_NET_HDR_GSO_UDP packets in tuntap.

To support SKB_GSO_UDP reappearing in the stack, also reinstate
logic in act_csum and openvswitch. Achieve equivalence with v4.13 HEAD
by squashing in commit 93991221 ("net: skb_needs_check() removes
CHECKSUM_UNNECESSARY check for tx.") and reverting commit 8d63bee6
("net: avoid skb_warn_bad_offload false positives on UFO").

(*) To avoid having to bring back skb_shinfo(skb)->ip6_frag_id,
ipv6_proxy_select_ident is changed to return a __be32 and this is
assigned directly to the frag_hdr. Also, SKB_GSO_UDP is inserted
at the end of the enum to minimize code churn.

Tested
  Booted a v4.13 guest kernel with QEMU. On a host kernel before this
  patch `ethtool -k eth0` shows UFO disabled. After the patch, it is
  enabled, same as on a v4.13 host kernel.

  A UFO packet sent from the guest appears on the tap device:
    host:
      nc -l -p -u 8000 &
      tcpdump -n -i tap0

    guest:
      dd if=/dev/zero of=payload.txt bs=1 count=2000
      nc -u 192.16.1.1 8000 < payload.txt

  Direct tap to tap transmission of VIRTIO_NET_HDR_GSO_UDP succeeds,
  packets arriving fragmented:

    ./with_tap_pair.sh ./tap_send_ufo tap0 tap1
    (from https://github.com/wdebruij/kerneltools/tree/master/tests)

Changes
  v1 -> v2
    - simplified set_offload change (review comment)
    - documented test procedure

Link: http://lkml.kernel.org/r/<CAF=yD-LuUeDuL9YWPJD9ykOZ0QCjNeznPDr6whqZ9NGMNF12Mw@mail.gmail.com>
Fixes: fb652fdf ("macvlan/macvtap: Remove NETIF_F_UFO advertisement.")
Reported-by: NMichal Kubecek <mkubecek@suse.cz>
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 6fa1ba61 partially
implemented the new ethtool API, by replacing get_settings()
with get_link_ksettings(). This breaks ethtool, since the
userspace tool (according to the new API specs) never tries
the legacy set() call, when the new get() call succeeds.

All attempts to chance some setting from userspace result in:
> Cannot set new settings: Operation not supported

Implement the missing set() call.
Signed-off-by: NTobias Jakobi <tjakobi@math.uni-bielefeld.de>
Tested-by: NHolger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change resolves a new compile-time warning
when built as a loadable module:

WARNING: modpost: missing MODULE_LICENSE() in drivers/net/phy/cortina.o
see include/linux/module.h for more information

This adds the license as "GPL", which matches the header of the file.

MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: NJesse Chan <jc@linux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40evf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with fm10k as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igb as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igbvf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with ixgbevf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40e as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes an issue seen on Power systems with ixgbe which results
in skb list corruption and an eventual kernel oops. The following is what
was observed:

CPU 1                                   CPU2
============================            ============================
1: ixgbe_xmit_frame_ring                ixgbe_clean_tx_irq
2:  first->skb = skb                     eop_desc = tx_buffer->next_to_watch
3:  ixgbe_tx_map                         read_barrier_depends()
4:   wmb                                 check adapter written status bit
5:   first->next_to_watch = tx_desc      napi_consume_skb(tx_buffer->skb ..);
6:   writel(i, tx_ring->tail);

The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not
get loaded prior to tx_buffer->next_to_watch, which then results in loading
a stale skb pointer. This patch replaces the read_barrier_depends with
smp_rmb to ensure loads are ordered with respect to the load of
tx_buffer->next_to_watch.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

After a reset we rebuild the VSIs which is going to clobber any
promiscuous settings we had before reset.  This makes it so that we
restore the promiscuous settings we had before reset.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current method for notifying clients of l2 parameters is broken
because we fail to copy the new parameters to the client instance
struct, we need to do the notification before the client 'open' function
pointer gets called, and lastly we should set the l2 parameters when
first adding a client instance.

This patch first introduces the i40evf_client_get_params function to
prevent code duplication in the i40evf_client_add_instance and the
i40evf_notify_client_l2_params functions.  We then fix the notify l2
params function to actually copy the parameters to client instance
struct and do the same in the *_add_instance' function.  Lastly this
patch reorganizes the priority in which client tasks fire so that if the
flag for notifying l2 params is set, it will trigger before the open
because the client needs these new parameters as part of a client open
task.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch allows detection of upcoming core reset in case NIC gets
stuck while performing FLR reset. The i40e_pf_reset() function returns
I40E_ERR_NOT_READY when global reset was detected.
Signed-off-by: NFilip Sadowski <filip.sadowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It is safe to remove the upper limit of 64 queues on a channel
VSI. The upper bound is determined by the VSI's num_queue_pairs
and gets validated when the queue mapping info through mqprio
interface is subject to bound checking in the driver.
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

num_mac should be increased only after the call to i40e_add_mac_filter().

Fixes: 5f527ba9 ("i40e: Limit the number of MAC and VLAN addresses that can be added for VFs")
Signed-off-by: NZijie Pan <zijie.pan@6wind.com>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: NTushar Dave <tushar.n.dave@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since commit 96a39aed ("i40e: Acquire NVM lock before
reads on all devices") we've used the NVM lock
to synchronize NVM reads even on devices which don't strictly
need the lock.

Doing so can cause a regression on older firmware prior to 1.5,
especially when downgrading the firmware.

Fix this by only grabbing the lock if we're running on an X722
device (which requires the lock as it uses the AdminQ to read
the NVM), or if we're currently running 1.5 or newer firmware.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 0115552e ("nfp: remove false positive offloads
in flower vxlan") missed adding kdoc for a new parameter
of nfp_flower_add_offload().
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Quectel BG96 is an Qualcomm MDM9206 based IoT modem, supporting both
CAT-M and NB-IoT. Tested hardware is BG96 mounted on Quectel development
board (EVB). The USB id is added to qmi_wwan.c to allow QMI
communication with the BG96.
Signed-off-by: NSebastian Sjoholm <ssjoholm@mac.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some systems, when we unsplit a port we need to re-create two ports
instead. On other systems, only one needs to be re-created.

Do not try to create a port if during driver initialization it was
assigned a negative module number, which is invalid.

This avoids the following error during unsplit:
[  941.012478] mlxsw_spectrum 0000:01:00.0: Port 43: Failed to map module

The error is harmless and caused by the fact that a local port is
already mapped to module 0.

Fixes: be94535f ("mlxsw: spectrum: Make split flow match firmware requirements")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With TC shared block changes we can't depend on correct netdev
pointer being available in cls_bpf.  Move the device validation
to the driver.  Core will only make sure that offloaded programs
are always attached in the driver (or in HW by the driver).  We
trust that drivers which implement offload callbacks will perform
necessary checks.

Moving the checks to the driver is generally a useful thing,
in practice the check should be against a switchdev instance,
not a netdev, given that most ASICs will probably allow using
the same program on many ports.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.

To make things worse, the parent mmio node was also prematurely freed.

Fixes: fd52bdae ("wcn36xx: Disable 5GHz for wcn3620")
Cc: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Make sure 16-byte mic is removed from the rx data packet
tail when CCMP-256, GCMP and GCMP-256 ciphers are used
in raw decap mode. This fixed rx traffic failures in those
ciphers in raw mode. Split the helper returning crypto
tail length into two, one to get the ICV length and other
to get the mic lengh for the cipher to make it clean.

Fixes: 2ea9f12c ("ath10k: add new cipher suite support")
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

hwsim_new_radio_nl() now copies the name attribute in order to add a
null-terminator.  mac80211_hwsim_new_radio() (indirectly) copies it
again into the net_device structure, so the first copy is not used or
freed later.  Free the first copy before returning.

Fixes: ff4dd73d ("mac80211_hwsim: check HWSIM_ATTR_RADIO_NAME length")
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some statements are not enough or too much indented.
Fix it to improve readalbility.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In rare cases, ena driver would reset and re-start the device,
for example, in case of misbehaving application that causes
transmit timeout

The first step in the reset procedure is to stop the Tx traffic by
calling ena_carrier_off().

After the driver have just started the device reset procedure, device
happens to send an asynchronous notification (via AENQ) to the driver
than there was a link change (to link-up state).
This link change is mapped to a call to netif_carrier_on() which
re-activates the Tx queues, violating the assumption of no tx traffic
until device reset is completed, as the reset task might still be in
the process of queues initialization, leading to an access to
uninitialized memory.
Signed-off-by: NNetanel Belgazal <netanel@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust the code to use the same green settings as in the latest
vendor driver.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Name of functions rtl_w0w1_eri and rtl_w0w1_phy is somewhat misleading
regarding order of arguments. One could assume that w0w1 means
argument with bits to be reset comes before argument with bits to set.
However this is not the case.
So fix the order of arguments in several statements.

In addition fix EEE advertisement. The current code resets the bits
for 100BaseT and 1000BaseT EEE advertisement what is not what we want.

I have a little of a hard time to find a proper "Fixes" line as the
issue seems to have been there forever (at least it existed already
when the driver was moved to the current place in 2011).

The patch was tested on a Zotac Mini-PC with a RTL8111E-VL chip.
Before the patch EEE was disabled, now it's properly advertised and
works fine.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rcu_read_lock in tun_build_skb is used to rcu_dereference tun->xdp_prog
safely, rcu_read_unlock should be done in every return path.

Now I could see one place missing it, where it returns NULL in switch-case
XDP_REDIRECT,  another palce using rcu_read_lock wrongly, where it returns
NULL in if (xdp_xmit) chunk.

So fix both in this patch.

Fixes: 761876c8 ("tap: XDP support")
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

_dev_ is being dereferenced before it is null checked, hence there
is a potential null pointer dereference.

Fix this by moving the pointer dereference after _dev_ has been null
checked.

Addresses-Coverity-ID: 1462020
Fixes: bb1b40c7 ("usbnet: ipheth: prevent TX queue timeouts when device not ready")
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to #define the license of the driver, just put it in
the MODULE_LICENSE() line directly as a text string.

This allows tools that check that the module license matches the source
code license to work properly, as there is no need to unwind the
unneeded dereference.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: Johan Hovold <johan@kernel.org>
Reported-by: NPhilippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: NPhilippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the dma_mapping_error call to use the correct dma_addr
which is inside the ibmvnic_vpd struct. Moreover, it fixes an uninitialized
warning regarding a local dma_addr variable which is not used anymore.

Fixes: 4e6759be ("ibmvnic: Feature implementation of VPD for the ibmvnic driver")
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDesnes A. Nunes do Rosario <desnesn@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When call to register_netdevice() (called from ipvlan_link_new()) fails,
we call ipvlan_uninit() (through ndo_uninit()) to destroy the ipvlan
port. After returning unsuccessfully from register_netdevice() we go
ahead and call ipvlan_port_destroy() again which causes NULL pointer
dereference panic. Fix the issue by making ipvlan_init() and
ipvlan_uninit() call symmetric.

The ipvlan port will now be created inside ipvlan_init() and will be
destroyed in ipvlan_uninit().

Fixes: 2ad7bf36 (ipvlan: Initial check-in of the IPVLAN driver)
Signed-off-by: NGirish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>