- 01 4月, 2019 7 次提交
-
-
由 David S. Miller 提交于
Aaro Koskinen says: ==================== net: stmmac: fix handling of oversized frames I accidentally had MTU size mismatch (9000 vs. 1500) in my network, and I noticed I could kill a system using stmmac & 1500 MTU simply by pinging it with "ping -s 2000 ...". While testing a fix I encountered also some other issues that need fixing. I have tested these only with enhanced descriptors, so the normal descriptor changes need a careful review. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Aaro Koskinen 提交于
This is log is harmful as it can trigger multiple times per packet. Delete it. Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Aaro Koskinen 提交于
Packets without the last descriptor set should be dropped early. If we receive a frame larger than the DMA buffer, the HW will continue using the next descriptor. Driver mistakes these as individual frames, and sometimes a truncated frame (without the LD set) may look like a valid packet. This fixes a strange issue where the system replies to 4098-byte ping although the MTU/DMA buffer size is set to 4096, and yet at the same time it's logging an oversized packet. Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Aaro Koskinen 提交于
If we have error bits set, the discard_frame status will get overwritten by checksum bit checks, which might set the status back to good one. Fix by checking the COE status only if the frame is good. Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Aaro Koskinen 提交于
Currently, if we drop a packet, we exit from NAPI loop before the budget is consumed. In some situations this will make the RX processing stall e.g. when flood pinging the system with oversized packets, as the errorneous packets are not dropped efficiently. If we drop a packet, we should just continue to the next one as long as the budget allows. Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Aaro Koskinen 提交于
Ratelimit RX error logs. Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Aaro Koskinen 提交于
We always program the maximum DMA buffer size into the receive descriptor, although the allocated size may be less. E.g. with the default MTU size we allocate only 1536 bytes. If somebody sends us a bigger frame, then memory may get corrupted. Fix by using exact buffer sizes. Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 31 3月, 2019 1 次提交
-
-
由 Heiner Kallweit 提交于
It was reported that re-introducing ASPM, in combination with RX interrupt coalescing, results in significantly increased packet latency, see [0]. Disabling ASPM or RX interrupt coalescing fixes the issue. Therefore change the driver's default to disable RX interrupt coalescing. Users still have the option to enable RX coalescing via ethtool. [0] https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=925496 Fixes: a99790bf ("r8169: Reinstate ASPM Support") Reported-by: NMike Crowe <mac@mcrowe.com> Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 3月, 2019 24 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf由 David S. Miller 提交于
Daniel Borkmann says: ==================== pull-request: bpf 2019-03-29 The following pull-request contains BPF updates for your *net* tree. The main changes are: 1) Bug fix in BTF deduplication that was mishandling an equivalence comparison, from Andrii. 2) libbpf Makefile fixes to properly link against libelf for the shared object and to actually export AF_XDP's xsk.h header, from Björn. 3) Fix use after free in bpf inode eviction, from Daniel. 4) Fix a bug in skb creation out of cpumap redirect, from Jesper. 5) Remove an unnecessary and triggerable WARN_ONCE() in max number of call stack frames checking in verifier, from Paul. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux由 David S. Miller 提交于
Saeed Mahameed says: ==================== Mellanox, mlx5 fixes 2019-03-29 This series introduces some fixes to mlx5 driver. Please pull and let me know if there is any problem. For -stable v4.11 ('net/mlx5: Decrease default mr cache size') For -stable v4.12 ('net/mlx5e: Add a lock on tir list') For -stable v4.13 ('net/mlx5e: Fix error handling when refreshing TIRs') For -stable v4.18 ('net/mlx5e: Update xon formula') For -stable v4.19 ('net: mlx5: Add a missing check on idr_find, free buf') ('net/mlx5e: Update xoff formula') net-next merge Note: When merged with net-next the following simple conflict will appear, drivers/net/ethernet/mellanox/mlx5/core/en/port_buffer.c ++<<<<<<< HEAD (net) + * max_mtu: netdev's max_mtu ++======= + * @mtu: device's MTU ++>>>>>>> net-next To resolve: just replace the line in net-next * @mtu: device's MTU to * @max_mtu: netdev's max_mtu ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
This reverts commit 4d31c4fa. Accidently applied this to the wrong tree. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vishal Kulkarni 提交于
Change t4fw_version.h to update latest firmware version number to 1.23.3.0. Signed-off-by: NVishal Kulkarni <vishal@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Li RongQing 提交于
NULL or ZERO_SIZE_PTR will be returned for zero sized memory request, and derefencing them will lead to a segfault so it is unnecessory to call vzalloc for zero sized memory request and not call functions which maybe derefence the NULL allocated memory this also fixes a possible memory leak if phy_ethtool_get_stats returns error, memory should be freed before exit Signed-off-by: NLi RongQing <lirongqing@baidu.com> Reviewed-by: NWang Li <wangli39@baidu.com> Reviewed-by: NMichal Kubecek <mkubecek@suse.cz> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jakub Kicinski 提交于
Only decrypt_internal() performs zero copy on rx, all paths which don't hit decrypt_internal() must set zc to false, otherwise tls_sw_recvmsg() may return 0 causing the application to believe that that connection got closed. Currently this happens with device offload when new record is first read from. Fixes: d069b780 ("tls: Fix tls_device receive") Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: NSimon Horman <simon.horman@netronome.com> Reported-by: NDavid Beckett <david.beckett@netronome.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Haiyang Zhang 提交于
After queue stopped, the wakeup mechanism may wake it up again when ring buffer usage is lower than a threshold. This may cause send path panic on NULL pointer when we stopped all tx queues in netvsc_detach and start removing the netvsc device. This patch fix it by adding a tx_disable flag to prevent unwanted queue wakeup. Fixes: 7b2ee50c ("hv_netvsc: common detach logic") Reported-by: NMohammed Gamal <mgamal@redhat.com> Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Konstantin Khorenko 提交于
Bond expects ethernet hwaddr for its slave, but it can be longer than 6 bytes - infiniband interface for example. # cat /sys/devices/<skipped>/net/ib0/address 80:00:02:08:fe:80:00:00:00:00:00:00:7c:fe:90:03:00:be:5d:e1 # cat /sys/devices/<skipped>/net/ib0/bonding_slave/perm_hwaddr 80:00:02:08:fe:80 So print full hwaddr in sysfs "bonding_slave/perm_hwaddr" as well. Signed-off-by: NKonstantin Khorenko <khorenko@virtuozzo.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eli Britstein 提交于
The driver allocates an encap context based on the tunnel properties, and reuse that context for all flows using the same tunnel properties. Commit df2ef3bf ("net/mlx5e: Add GRE protocol offloading") introduced another tunnel protocol other than the single VXLAN previously supported. A flow that uses a tunnel with the same tunnel properties but with a different tunnel type (GRE vs VXLAN for example) would mistakenly reuse the previous alocated context, causing the traffic to be sent with the wrong encapsulation. Fix that by considering the tunnel type for encap contexts. Fixes: df2ef3bf ("net/mlx5e: Add GRE protocol offloading") Signed-off-by: NEli Britstein <elibr@mellanox.com> Reviewed-by: NRoi Dayan <roid@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
由 Huy Nguyen 提交于
Set xon = xoff - netdev's max_mtu. netdev's max_mtu will give enough time for the pause frame to arrive at the sender. Fixes: 0696d608 ("net/mlx5e: Receive buffer configuration") Signed-off-by: NHuy Nguyen <huyn@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
由 Huy Nguyen 提交于
Set minimum speed in xoff threshold formula to 40Gbps Fixes: 0696d608 ("net/mlx5e: Receive buffer configuration") Signed-off-by: NHuy Nguyen <huyn@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
由 Huy Nguyen 提交于
Make sure the struct mlx5_flow_destination is zero before filling in the field. Fixes: 8da202b2 ("net/mlx5: E-Switch, Add support for VEPA in legacy mode.") Signed-off-by: NHuy Nguyen <huyn@mellanox.com> Reviewed-by: NDaniel Jurgens <danielj@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
由 Omri Kahalon 提交于
Traditionally, the PF (Physical Function) which resides on vport 0 was the E-switch manager. Since the ECPF (Embedded CPU Physical Function), which resides on vport 0xfffe, was introduced as the E-Switch manager, the assumption that the E-switch manager is on vport 0 is incorrect. Since the eswitch code already uses the actual vport value, all we need is to always set other_vport=1. Signed-off-by: NOmri Kahalon <omrik@mellanox.com> Reviewed-by: NMax Gurtovoy <maxg@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
由 Roi Dayan 提交于
The esw offloads structures share a union with the legacy mode structs. Reset the offloads struct to zero in init to protect from null assumptions made by the legacy mode code. Signed-off-by: NRoi Dayan <roid@mellanox.com> Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
由 Tonghao Zhang 提交于
The capacity of FDB offloading and NIC offloading table are different, and when allocating the pedit actions, we should use the correct namespace type. Fixes: c500c86b ("net/mlx5e: support for two independent packet edit actions") Cc: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: NTonghao Zhang <xiangxia.m.yue@gmail.com> Reviewed-by: NRoi Dayan <roid@mellanox.com> Acked-by: NPablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
由 Roi Dayan 提交于
The esw fdb table has a union of legacy and offloads members. So if we were in a certain esw mode we could set some memebers and not set null which is fine as on destroy path and don't care. But then moving from legacy to switchdev a second time, the cleanup flow of legacy mode checks if a struct member was in use if it's not null so we need to make sure to reset the code to null when we init legacy mode. Fixes: 8da202b2 ("net/mlx5: E-Switch, Add support for VEPA in legacy mode.") Signed-off-by: NRoi Dayan <roid@mellanox.com> Reviewed-by: NHuy Nguyen <huyn@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
由 Aya Levin 提交于
Allow configuration of legacy link-modes even when extended link-modes are supported. This requires reading of legacy advertisement even when extended link-modes are supported. Since legacy and extended advertisement are mutually excluded, wait for empty reply from extended advertisement before reading legacy advertisement. Fixes: 6a897372 ("net/mlx5: ethtool, Add ethtool support for 50Gbps per lane link modes") Signed-off-by: NAya Levin <ayal@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
由 Aya Levin 提交于
Ethtool option set_link_ksettings allows setting of legacy link-modes or extended link-modes. Refine the decision of which type of link-modes is set. Fixes: 6a897372 ("net/mlx5: ethtool, Add ethtool support for 50Gbps per lane link modes") Signed-off-by: NAya Levin <ayal@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
由 Yuval Avnery 提交于
Refresh tirs is looping over a global list of tirs while netdevs are adding and removing tirs from that list. That is why a lock is required. Fixes: 724b2aa1 ("net/mlx5e: TIRs management refactoring") Signed-off-by: NYuval Avnery <yuvalav@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
由 Aditya Pakki 提交于
idr_find() can return a NULL value to 'flow' which is used without a check. The patch adds a check to avoid potential NULL pointer dereference. In case of mlx5_fpga_sbu_conn_sendmsg() failure, free buf allocated using kzalloc. Fixes: ab412e1d ("net/mlx5: Accel, add TLS rx offload routines") Signed-off-by: NAditya Pakki <pakki001@umn.edu> Reviewed-by: NYuval Shaia <yuval.shaia@oracle.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
由 Dmytro Linkin 提交于
For some protocols we are not allowing IP header rewrite offload, since the HW is not capable to properly adjust the l4 checksum. However, TTL & HOPLIMIT modification can be done for all IP protocols, because they are not part of the pseudo header taken into account for checksum. Fixes: 73867881 ("drivers: net: use flow action infrastructure") Signed-off-by: NDmytro Linkin <dmitrolin@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
由 Gavi Teitz 提交于
Previously, a false positive would be caught if the TIRs list is empty, since the err value was initialized to -ENOMEM, and was only updated if a TIR is refreshed. This is resolved by initializing the err value to zero. Fixes: b676f653 ("net/mlx5e: Refactor refresh TIRs") Signed-off-by: NGavi Teitz <gavi@mellanox.com> Reviewed-by: NRoi Dayan <roid@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
由 Artemy Kovalyov 提交于
Delete initialization of high order entries in mr cache to decrease initial memory footprint. When required, the administrator can populate the entries with memory keys via the /sys interface. This approach is very helpful to significantly reduce the per HW function memory footprint in virtualization environments such as SRIOV. Fixes: 9603b61d ("mlx5: Move pci device handling from mlx5_ib to mlx5_core") Signed-off-by: NArtemy Kovalyov <artemyko@mellanox.com> Signed-off-by: NMoni Shoua <monis@mellanox.com> Signed-off-by: NLeon Romanovsky <leonro@mellanox.com> Reported-by: NShalom Toledo <shalomt@mellanox.com> Acked-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
由 Jesper Dangaard Brouer 提交于
We want to avoid leaking pointer info from xdp_frame (that is placed in top of frame) like commit 6dfb970d ("xdp: avoid leaking info stored in frame data on page reuse"), and followup commit 97e19cce ("bpf: reserve xdp_frame size in xdp headroom") that reserve this headroom. These changes also affected how cpumap constructed SKBs, as xdpf->headroom size changed, the skb data starting point were in-effect shifted with 32 bytes (sizeof xdp_frame). This was still okay, as the cpumap frame_size calculation also included xdpf->headroom which were reduced by same amount. A bug was introduced in commit 77ea5f4c ("bpf/cpumap: make sure frame_size for build_skb is aligned if headroom isn't"), where the xdpf->headroom became part of the SKB_DATA_ALIGN rounding up. This round-up to find the frame_size is in principle still correct as it does not exceed the 2048 bytes frame_size (which is max for ixgbe and i40e), but the 32 bytes offset of pkt_data_start puts this over the 2048 bytes limit. This cause skb_shared_info to spill into next frame. It is a little hard to trigger, as the SKB need to use above 15 skb_shinfo->frags[] as far as I calculate. This does happen in practise for TCP streams when skb_try_coalesce() kicks in. KASAN can be used to detect these wrong memory accesses, I've seen: BUG: KASAN: use-after-free in skb_try_coalesce+0x3cb/0x760 BUG: KASAN: wild-memory-access in skb_release_data+0xe2/0x250 Driver veth also construct a SKB from xdp_frame in this way, but is not affected, as it doesn't reserve/deduct the room (used by xdp_frame) from the SKB headroom. Instead is clears the pointers via xdp_scrub_frame(), and allows SKB to use this area. The fix in this patch is to do like veth and instead allow SKB to (re)use the area occupied by xdp_frame, by clearing via xdp_scrub_frame(). (This does kill the idea of the SKB being able to access (mem) info from this area, but I guess it was a bad idea anyhow, and it was already killed by the veth changes.) Fixes: 77ea5f4c ("bpf/cpumap: make sure frame_size for build_skb is aligned if headroom isn't") Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
- 29 3月, 2019 8 次提交
-
-
由 Alexander Lobakin 提交于
__netif_receive_skb_list_ptype() leaves skb->next poisoned before passing it to pt_prev->func handler, what may produce (in certain cases, e.g. DSA setup) crashes like: [ 88.606777] CPU 0 Unable to handle kernel paging request at virtual address 0000000e, epc == 80687078, ra == 8052cc7c [ 88.618666] Oops[#1]: [ 88.621196] CPU: 0 PID: 0 Comm: swapper Not tainted 5.1.0-rc2-dlink-00206-g4192a172-dirty #1473 [ 88.630885] $ 0 : 00000000 10000400 00000002 864d7850 [ 88.636709] $ 4 : 87c0ddf0 864d7800 87c0ddf0 00000000 [ 88.642526] $ 8 : 00000000 49600000 00000001 00000001 [ 88.648342] $12 : 00000000 c288617b dadbee27 25d17c41 [ 88.654159] $16 : 87c0ddf0 85cff080 80790000 fffffffd [ 88.659975] $20 : 80797b20 ffffffff 00000001 864d7800 [ 88.665793] $24 : 00000000 8011e658 [ 88.671609] $28 : 80790000 87c0dbc0 87cabf00 8052cc7c [ 88.677427] Hi : 00000003 [ 88.680622] Lo : 7b5b4220 [ 88.683840] epc : 80687078 vlan_dev_hard_start_xmit+0x1c/0x1a0 [ 88.690532] ra : 8052cc7c dev_hard_start_xmit+0xac/0x188 [ 88.696734] Status: 10000404 IEp [ 88.700422] Cause : 50000008 (ExcCode 02) [ 88.704874] BadVA : 0000000e [ 88.708069] PrId : 0001a120 (MIPS interAptiv (multi)) [ 88.713005] Modules linked in: [ 88.716407] Process swapper (pid: 0, threadinfo=(ptrval), task=(ptrval), tls=00000000) [ 88.725219] Stack : 85f61c28 00000000 0000000e 80780000 87c0ddf0 85cff080 80790000 8052cc7c [ 88.734529] 87cabf00 00000000 00000001 85f5fb40 807b0000 864d7850 87cabf00 807d0000 [ 88.743839] 864d7800 8655f600 00000000 85cff080 87c1c000 0000006a 00000000 8052d96c [ 88.753149] 807a0000 8057adb8 87c0dcc8 87c0dc50 85cfff08 00000558 87cabf00 85f58c50 [ 88.762460] 00000002 85f58c00 864d7800 80543308 fffffff4 00000001 85f58c00 864d7800 [ 88.771770] ... [ 88.774483] Call Trace: [ 88.777199] [<80687078>] vlan_dev_hard_start_xmit+0x1c/0x1a0 [ 88.783504] [<8052cc7c>] dev_hard_start_xmit+0xac/0x188 [ 88.789326] [<8052d96c>] __dev_queue_xmit+0x6e8/0x7d4 [ 88.794955] [<805a8640>] ip_finish_output2+0x238/0x4d0 [ 88.800677] [<805ab6a0>] ip_output+0xc8/0x140 [ 88.805526] [<805a68f4>] ip_forward+0x364/0x560 [ 88.810567] [<805a4ff8>] ip_rcv+0x48/0xe4 [ 88.815030] [<80528d44>] __netif_receive_skb_one_core+0x44/0x58 [ 88.821635] [<8067f220>] dsa_switch_rcv+0x108/0x1ac [ 88.827067] [<80528f80>] __netif_receive_skb_list_core+0x228/0x26c [ 88.833951] [<8052ed84>] netif_receive_skb_list+0x1d4/0x394 [ 88.840160] [<80355a88>] lunar_rx_poll+0x38c/0x828 [ 88.845496] [<8052fa78>] net_rx_action+0x14c/0x3cc [ 88.850835] [<806ad300>] __do_softirq+0x178/0x338 [ 88.856077] [<8012a2d4>] irq_exit+0xbc/0x100 [ 88.860846] [<802f8b70>] plat_irq_dispatch+0xc0/0x144 [ 88.866477] [<80105974>] handle_int+0x14c/0x158 [ 88.871516] [<806acfb0>] r4k_wait+0x30/0x40 [ 88.876462] Code: afb10014 8c8200a0 00803025 <9443000c> 94a20468 00000000 10620042 00a08025 9605046a [ 88.887332] [ 88.888982] ---[ end trace eb863d007da11cf1 ]--- [ 88.894122] Kernel panic - not syncing: Fatal exception in interrupt [ 88.901202] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]--- Fix this by pulling skb off the sublist and zeroing skb->next pointer before calling ptype callback. Fixes: 88eb1944 ("net: core: propagate SKB lists through packet_type lookup") Reviewed-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NAlexander Lobakin <alobakin@dlink.ru> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Mao Wenan 提交于
When it is to cleanup net namespace, rds_tcp_exit_net() will call rds_tcp_kill_sock(), if t_sock is NULL, it will not call rds_conn_destroy(), rds_conn_path_destroy() and rds_tcp_conn_free() to free connection, and the worker cp_conn_w is not stopped, afterwards the net is freed in net_drop_ns(); While cp_conn_w rds_connect_worker() will call rds_tcp_conn_path_connect() and reference 'net' which has already been freed. In rds_tcp_conn_path_connect(), rds_tcp_set_callbacks() will set t_sock = sock before sock->ops->connect, but if connect() is failed, it will call rds_tcp_restore_callbacks() and set t_sock = NULL, if connect is always failed, rds_connect_worker() will try to reconnect all the time, so rds_tcp_kill_sock() will never to cancel worker cp_conn_w and free the connections. Therefore, the condition !tc->t_sock is not needed if it is going to do cleanup_net->rds_tcp_exit_net->rds_tcp_kill_sock, because tc->t_sock is always NULL, and there is on other path to cancel cp_conn_w and free connection. So this patch is to fix this. rds_tcp_kill_sock(): ... if (net != c_net || !tc->t_sock) ... Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com> ================================================================== BUG: KASAN: use-after-free in inet_create+0xbcc/0xd28 net/ipv4/af_inet.c:340 Read of size 4 at addr ffff8003496a4684 by task kworker/u8:4/3721 CPU: 3 PID: 3721 Comm: kworker/u8:4 Not tainted 5.1.0 #11 Hardware name: linux,dummy-virt (DT) Workqueue: krdsd rds_connect_worker Call trace: dump_backtrace+0x0/0x3c0 arch/arm64/kernel/time.c:53 show_stack+0x28/0x38 arch/arm64/kernel/traps.c:152 __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x120/0x188 lib/dump_stack.c:113 print_address_description+0x68/0x278 mm/kasan/report.c:253 kasan_report_error mm/kasan/report.c:351 [inline] kasan_report+0x21c/0x348 mm/kasan/report.c:409 __asan_report_load4_noabort+0x30/0x40 mm/kasan/report.c:429 inet_create+0xbcc/0xd28 net/ipv4/af_inet.c:340 __sock_create+0x4f8/0x770 net/socket.c:1276 sock_create_kern+0x50/0x68 net/socket.c:1322 rds_tcp_conn_path_connect+0x2b4/0x690 net/rds/tcp_connect.c:114 rds_connect_worker+0x108/0x1d0 net/rds/threads.c:175 process_one_work+0x6e8/0x1700 kernel/workqueue.c:2153 worker_thread+0x3b0/0xdd0 kernel/workqueue.c:2296 kthread+0x2f0/0x378 kernel/kthread.c:255 ret_from_fork+0x10/0x18 arch/arm64/kernel/entry.S:1117 Allocated by task 687: save_stack mm/kasan/kasan.c:448 [inline] set_track mm/kasan/kasan.c:460 [inline] kasan_kmalloc+0xd4/0x180 mm/kasan/kasan.c:553 kasan_slab_alloc+0x14/0x20 mm/kasan/kasan.c:490 slab_post_alloc_hook mm/slab.h:444 [inline] slab_alloc_node mm/slub.c:2705 [inline] slab_alloc mm/slub.c:2713 [inline] kmem_cache_alloc+0x14c/0x388 mm/slub.c:2718 kmem_cache_zalloc include/linux/slab.h:697 [inline] net_alloc net/core/net_namespace.c:384 [inline] copy_net_ns+0xc4/0x2d0 net/core/net_namespace.c:424 create_new_namespaces+0x300/0x658 kernel/nsproxy.c:107 unshare_nsproxy_namespaces+0xa0/0x198 kernel/nsproxy.c:206 ksys_unshare+0x340/0x628 kernel/fork.c:2577 __do_sys_unshare kernel/fork.c:2645 [inline] __se_sys_unshare kernel/fork.c:2643 [inline] __arm64_sys_unshare+0x38/0x58 kernel/fork.c:2643 __invoke_syscall arch/arm64/kernel/syscall.c:35 [inline] invoke_syscall arch/arm64/kernel/syscall.c:47 [inline] el0_svc_common+0x168/0x390 arch/arm64/kernel/syscall.c:83 el0_svc_handler+0x60/0xd0 arch/arm64/kernel/syscall.c:129 el0_svc+0x8/0xc arch/arm64/kernel/entry.S:960 Freed by task 264: save_stack mm/kasan/kasan.c:448 [inline] set_track mm/kasan/kasan.c:460 [inline] __kasan_slab_free+0x114/0x220 mm/kasan/kasan.c:521 kasan_slab_free+0x10/0x18 mm/kasan/kasan.c:528 slab_free_hook mm/slub.c:1370 [inline] slab_free_freelist_hook mm/slub.c:1397 [inline] slab_free mm/slub.c:2952 [inline] kmem_cache_free+0xb8/0x3a8 mm/slub.c:2968 net_free net/core/net_namespace.c:400 [inline] net_drop_ns.part.6+0x78/0x90 net/core/net_namespace.c:407 net_drop_ns net/core/net_namespace.c:406 [inline] cleanup_net+0x53c/0x6d8 net/core/net_namespace.c:569 process_one_work+0x6e8/0x1700 kernel/workqueue.c:2153 worker_thread+0x3b0/0xdd0 kernel/workqueue.c:2296 kthread+0x2f0/0x378 kernel/kthread.c:255 ret_from_fork+0x10/0x18 arch/arm64/kernel/entry.S:1117 The buggy address belongs to the object at ffff8003496a3f80 which belongs to the cache net_namespace of size 7872 The buggy address is located 1796 bytes inside of 7872-byte region [ffff8003496a3f80, ffff8003496a5e40) The buggy address belongs to the page: page:ffff7e000d25a800 count:1 mapcount:0 mapping:ffff80036ce4b000 index:0x0 compound_mapcount: 0 flags: 0xffffe0000008100(slab|head) raw: 0ffffe0000008100 dead000000000100 dead000000000200 ffff80036ce4b000 raw: 0000000000000000 0000000080040004 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8003496a4580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8003496a4600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff8003496a4680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff8003496a4700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8003496a4780: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== Fixes: 467fa153("RDS-TCP: Support multiple RDS-TCP listen endpoints, one per netns.") Reported-by: NHulk Robot <hulkci@huawei.com> Signed-off-by: NMao Wenan <maowenan@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrea Righi 提交于
The flow action buffer can be resized if it's not big enough to contain all the requested flow actions. However, this resize doesn't take into account the new requested size, the buffer is only increased by a factor of 2x. This might be not enough to contain the new data, causing a buffer overflow, for example: [ 42.044472] ============================================================================= [ 42.045608] BUG kmalloc-96 (Not tainted): Redzone overwritten [ 42.046415] ----------------------------------------------------------------------------- [ 42.047715] Disabling lock debugging due to kernel taint [ 42.047716] INFO: 0x8bf2c4a5-0x720c0928. First byte 0x0 instead of 0xcc [ 42.048677] INFO: Slab 0xbc6d2040 objects=29 used=18 fp=0xdc07dec4 flags=0x2808101 [ 42.049743] INFO: Object 0xd53a3464 @offset=2528 fp=0xccdcdebb [ 42.050747] Redzone 76f1b237: cc cc cc cc cc cc cc cc ........ [ 42.051839] Object d53a3464: 6b 6b 6b 6b 6b 6b 6b 6b 0c 00 00 00 6c 00 00 00 kkkkkkkk....l... [ 42.053015] Object f49a30cc: 6c 00 0c 00 00 00 00 00 00 00 00 03 78 a3 15 f6 l...........x... [ 42.054203] Object acfe4220: 20 00 02 00 ff ff ff ff 00 00 00 00 00 00 00 00 ............... [ 42.055370] Object 21024e91: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 42.056541] Object 070e04c3: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 42.057797] Object 948a777a: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 42.059061] Redzone 8bf2c4a5: 00 00 00 00 .... [ 42.060189] Padding a681b46e: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ Fix by making sure the new buffer is properly resized to contain all the requested data. BugLink: https://bugs.launchpad.net/bugs/1813244Signed-off-by: NAndrea Righi <andrea.righi@canonical.com> Acked-by: NPravin B Shelar <pshelar@ovn.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Jakub Kicinski says: ==================== nfp: fix retcode and disable netpoll on representors This series avoids a potential crash on nfp representor devices when netpoll is in use. If transmitting the frame through underlying vNIC fails we'd return an error code (by passing on error code from __dev_queue_xmit()) and cause double free in netpoll code. Fix the error code and disable netpoll on reprs altogether. IRQ-safety of locking the queues and calling __dev_queue_xmit() is questionable. Big thanks to John Hurley for debugging and narrowing down the trace log after I gave up! :) ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jakub Kicinski 提交于
NFP reprs are software device on top of the PF's vNIC. The comment above __dev_queue_xmit() sayeth: When calling this method, interrupts MUST be enabled. This is because the BH enable code must have IRQs enabled so that it will not deadlock. For netconsole we can't guarantee IRQ state, let's just disable netpoll on representors to be on the safe side. When the initial implementation of NFP reprs was added by the commit 5de73ee4 ("nfp: general representor implementation") .ndo_poll_controller was required for netpoll to be enabled. Fixes: ac3d9dd0 ("netpoll: make ndo_poll_controller() optional") Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: NJohn Hurley <john.hurley@netronome.com> Reviewed-by: NSimon Horman <simon.horman@netronome.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jakub Kicinski 提交于
dev_queue_xmit() may return error codes as well as netdev_tx_t, and it always consumes the skb. Make sure we always return a correct netdev_tx_t value. Fixes: eadfa4c3 ("nfp: add stats and xmit helpers for representors") Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: NJohn Hurley <john.hurley@netronome.com> Reviewed-by: NSimon Horman <simon.horman@netronome.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
net_hash_mix() currently uses kernel address of a struct net, and is used in many places that could be used to reveal this address to a patient attacker, thus defeating KASLR, for the typical case (initial net namespace, &init_net is not dynamically allocated) I believe the original implementation tried to avoid spending too many cycles in this function, but security comes first. Also provide entropy regardless of CONFIG_NET_NS. Fixes: 0b441916 ("netns: introduce the net_hash_mix "salt" for hashes") Signed-off-by: NEric Dumazet <edumazet@google.com> Reported-by: NAmit Klein <aksecurity@gmail.com> Reported-by: NBenny Pinkas <benny@pinkas.net> Cc: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bjørn Mork 提交于
This is a Qualcomm based device with a QMI function on interface 4. It is mode switched from 2020:2030 using a standard eject message. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=2031 Rev= 2.32 S: Manufacturer=Mobile Connect S: Product=Mobile Connect S: SerialNumber=0123456789ABCDEF C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none) E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us Signed-off-by: NBjørn Mork <bjorn@mork.no> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-