When using the CLP interface to enable or disable a pci device a
valid function handle needs to be delivered. So far our assumption
was that we always have an up-to-date version of the function handle
(since it doesn't change when the device is in use). This assumption
is incorrect if the pci device is enabled or disabled outside of our
control. When we are notified about such a change we already receive
the new function handle. Just use it.
Reviewed-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

If we receive a notification that a pci function became unavailable we clean
up by removing the pci device. This can confuse the driver since the function
is already unaccessible. Improve this situation by setting an appropriate
error_state.
Reviewed-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

If we remove a pci bus after receiving a hotplug notification we need
to check if the bus is actually present (creation of the pci bus
during an earlier notification may have been failed).
Reviewed-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Initialization and scanning of the pci bus is omitted on older
machines without pci support or if pci=off was specified. Remember
the fact that we ran without pci support and prevent further bus
scans during resume from hibernate or after receiving hotplug
notifications.
Reported-by: NStefan Haberland <stefan.haberland@de.ibm.com>
Reviewed-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

When the availability of a pci function has changed by means
outside of our control we receive an availability event.
Implement/improve the handling of these notifications.
Reviewed-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Cleanup arch specific pci messages. Remove unhelpful messages and
replace others with entries in the debugfs.
Reviewed-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

List pci functions is used to query and iterate over pci functions.
This function currently has 2 users - initial device discovery and
rescan after a machine check. Instead of having a multipurpose
function pass a callback which gets called for each pci function.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add support for reading the PCI function measurement block counters
provided by the hypervisor. Add two s390 debug features, one for
critical errors and one for tracing and provide wrappers to log data.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add CHSC store-event-information support for PCI (notfication type 2)
and report error and availability events to the PCI architecture layer.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>