Use a safe strscpy call to copy the ethtool stat strings into the
relevant buffers, instead of a memcpy that will be accessing
out-of-bound data.

Fixes: 118d6298 ("net: mvpp2: add ethtool GOP statistics")
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MVPP2_TXQ_SCHED_TOKEN_CNTR_REG() expects the logical queue id but
the current code is passing the global tx queue offset, so it ends
up writing to unknown registers (between 0x8280 and 0x82fc, which
seemed to be unused by the hardware). This fixes the issue by using
the logical queue id instead.

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the mvpp2 driver supports classification offloading, we must
add the NETIF_F_NTUPLE to the features list.

Since the current code doesn't allow disabling the feature, we don't set
the flag in dev->hw_features.

Fixes: 90b509b3 ("net: mvpp2: cls: Add Classification offload support")
Reported-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit introduces basic classification offloading support for the
PPv2 controller.

The PPv2 classifier has many classification engines, for now we only use
the C2 TCAM match engine.

This engine allows to perform ternary lookups on 64 bits keys (called
Header Extracted Key), that are built by extracting fields from the packet
header and concatenating them. At most 4 fields can be extracted for a
single lookup.

This basic implementation allows to build the HEK from the following
fields :
 - L4 source and destination ports (for UDP and TCP)

More fields are to be added in the future.

Classification flows are added through the ethtool interface, using the
newly introduced flow_rule infrastructure as an internal rule
representation, allowing to more easily implement tc flower rules if
need be.

The internal design for now allocates one range of 4 rules per port
due to the internal design of the flow table, which uses 22 sub-flows.

When inserting a classification rule, the rule is created in every
relevant sub-flow.

This low rule-count is a very simple design which reaches quickly the
limitations of the flow table ordering, but guarantees that the rule
ordering will always be respected.

This commit only introduces support for the "steer to rxq" action.
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit renames some of the classifier functions to follow the
naming 'mvpp2_port_*' that's used for function that act on a given port.

This commit is purely cosmetic.
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

int is not long enough to store all netdev_features, use the correct
dedicated type to store them when building the list of dev->features.
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds calls in the stop() helper to ensure both MACs and
both PCS blocks are set in reset when the user manually sets a port
down. This is done so that we have the exact same block reset states at
boot time and when a port is set down.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch sets both the XPCS and MPCS blocks in reset when they aren't
used. This is done both at boot time and when reconfiguring a port mode.
The advantage now is that only the PCS used is set out of reset when the
port is configured (10GKR uses the MCPS while RXAUI uses the XPCS).
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes sure both PPv2 MACs (GMAC + XLG MAC) are set in reset
while a port is reconfigured. This is done so that we make sure a MAC is
in a reset state when not used, as only one of the two will be set out
of reset after the port is configured properly.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reworks the way the XLG MAC is set in reset: the XLG MAC is
set in reset at probe time and taken out of this state only when used.
The idea is to move forward a situation where only the blocks used are
taken out of reset. This also has the effect to handle the GMAC and the
XLG MAC in a similar way (the GMAC already is set in reset at boot
time).
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch force the XLG MAC link state in the phylink link_up() and
link_down() helpers when not using in-band auto-negotiation. This mimics
what's already done for the GMAC and follows what's advised in the
phylink documentation.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch improves the XLG configuration function, to only update the
XLG configuration register when a change is needed. This helps not
writing over and over the same XLG configuration each time phylink
request the MAC to be configured. This mimics the GMAC configuration
function.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch modifies the port_disable() helper to always disable both the
GMAC and the XLG MAC when called. At boot time we do not know of a port
was enabled in the firmware/bootloader, and if so what mode was used
(hence which of the two MACs was used).

This also help in implementing a logic where all blocks are disabled
when not used, and only enabled regarding the current mode used on a
given port.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The GMAC configuration helper modifies values in the auto-negotiation
register. Some of its values require the port to be forced down when
modifying their values. This patches fixes the check made on the bit to
be updated in this register, so that the port is forced down when
needed. This fix cases where some of those parameters were updated, but
not taken into account, such as when using RGMII interfaces.

Fixes: d14e078f ("net: marvell: mvpp2: only reprogram what is necessary on mac_config")
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch fixes the computation of RXQs being used by the PPv2 driver,
which is set depending on the PPv2 engine version and the queue mode
used. There are three cases:

- PPv2.1: 1 RXQ per CPU.
- PPV2.2 with MVPP2_QDIST_MULTI_MODE: 1 RXQ per CPU.
- PPv2.2 with MVPP2_QDIST_SINGLE_MODE: 1 RXQ is shared between the CPUs.

The PPv2 engine supports a maximum of 32 queues per port. This patch
adds a check so that we do not overstep this maximum.

It appeared the calculation was broken for PPv2.1 engines since
f8c6ba84, as PPv2.1 ports ended up with a single RXQ while they
needed 4. This patch fixes it.

Fixes: f8c6ba84 ("net: mvpp2: use only one rx queue per port per CPU")
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Phylink validate function is the Marvell PPv2 driver makes a check
on the GoP id. This is valid an has to be done when using PPv2.2 engines
but makes no sense when using PPv2.1. The check done when using an RGMII
interface makes sure the GoP id is not 0, but this breaks PPv2.1. Fixes
it.

Fixes: 0fb628f0 ("net: mvpp2: fix phylink handling of invalid PHY modes")
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a check on the PPv2 version in-use not to reconfigure
the port mode when an interface is updated when using PPv2.1 as the
functions called are PPv2.2 specific.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We had a check in the mvpp2_mac_link_down() function (called by phylink)
to avoid disabling the port when link interrupts are used. It turned out
the interrupt can still be used with the port disabled. We can thus
remove this check.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PPv2 controller is able to support 2.5G speeds, allowing to use
2.5GBASET in conjunction with PHYs that use 2500BASEX as their MII
interface when using this mode.
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are several places which make the decision whether to access the
XLGMAC vs GMAC that only check for PHY_INTERFACE_MODE_10GKR and not its
XAUI variant.  Switch these to use the new helper so that we have
consistency through the driver.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a mvpp2_is_xlg() helper to identify whether the interface mode
should be using the XLGMAC rather than the GMAC.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When mvpp2 configures the flow control modes in mvpp2_xlg_config() for
10G mode, it only ever set the flow control enable bits.  There is no
mechanism to clear these bits, which means that userspace is unable to
use standard APIs to disable flow control (the only way is to poke the
register directly.)

Fix the missing bit clearance to allow flow control to be disabled.
This means that, by default, as there is no negotiation in 10G modes
with mvpp2, flow control is now disabled rather than being rx-only.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phylink already limits which interface modes are able to call the
MACs AN restart function, but in any case, the commentry seems
incorrect: the AN restart bit does not automatically clear when
set.  This has been found via manual setting using devmem2, and
we can observe that the AN does indeed restart and complete, yet
the AN restart bit remains set.  Explicitly clear the AN restart
bit.
Tested-by: NSven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mac_config() can be called at any point, and the expected behaviour
from MAC drivers is to only reprogram when necessary - and certainly
avoid taking the link down on every call.

Unfortunately, mvpp2 does exactly that - it takes the link down, and
reprograms everything, and then releases the forced-link down.

This is bad, it can cause the link to bounce:

- SFP detects signal, disables LOS indication.
- SFP code calls into phylink, calling phylink_sfp_link_up() which
  triggers a resolve.
- phylink_resolve() calls phylink_get_mac_state() and finds the MAC
  reporting link up.
- phylink wants to configure the pause mode on the MAC, so calls
  phylink_mac_config()
- mvpp2 takes the link down temporarily, generating a MAC link down
  event followed by another MAC link event.
- phylink calls mac_link_up() and then processes the MAC link down
  event.
- phylink_resolve() gets called again, registers the link down, and
  calls mach_link_down() before re-running itself.
- phylink_resolve() starts again at step 3 above.  This sequence
  repeats.

GMAC versions prior to mvpp2 do not require the link to be taken down
except when certain link properties (eg, switching between SGMII and
1000base-X mode, or enabling/disabling in-band negotiation) are
changed.  Implement this for mvpp2.
Tested-by: NSven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It appears that the mvpp22 can get stuck with SGMII negotiation.  The
symptoms are that in-band negotiation never completes and the partner
(eg, PHY) never reports SGMII link up, or if it supports negotiation
bypass, goes into negotiation bypass mode (which will happen when the
PHY sees that the MAC is alive but gets no response.)

Triggering the PHY end of the link to re-negotiate results in the
bypass bit clearing on the PHY, and then re-setting - indicating that
the problem is at the mvpp22 GMAC end.

Asserting the GMAC reset and de-asserting it resolves the issue.
Arrange to assert the GMAC reset at probe time, and deassert it only
after we have configured the GMAC for the appropriate mode.  This
resolves the issue.
Tested-by: NSven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sven Auhagen reported issues with negotiation on a couple of his
platforms using a mixture of SFP and PHYs in various different
modes.  Debugging to root cause proved difficult, but essentially
the problem comes down to the mvpp2 phylink implementation being
slightly at odds with what is expected.

phylink operates in three modes: phy, fixed-link, and in-band mode.

In the first two modes, the expected behaviour from a MAC driver is
that phylink resolves the operating mode and passes the mode to the
MAC driver for it to program, including when the link should be
brought up or taken down.  This is basically the same as the libphy
approach.  This does not negate the requirement to advertise a correct
control word for interface modes that have control words where that
can be reasonably controlled.

The second mode is in-band mode, where the MAC is expected to use the
in-band control word to determine the operating mode.

The mvneta driver implements the correct pattern required to support
this: configure the port interface type separately from the in-band
mode(s).  This is now specified in the phylink documentation patches.

mvpp2 was programming in-band mode for SGMII and the 802.3z modes no
what, and avoided forcing the link up in fixed/phy modes.  This caused
a problem with some boards where the PHY is by default programmed to
enter AN bypass mode, the PHY would report that the link was up, but
the mvpp2 never completed the exchange of control word.

Another issue that mvpp2 has is it sets SGMII AN format control word
for both SGMII and 802.3z modes. The format of the control word is
defined by MVPP2_GMAC_INBAND_AN_MASK, which should be set for SGMII
and clear for 802.3z. Available Marvell documentation for earlier
GMAC implementations does not make this clear, but this has been
ascertained via extensive testing on earlier GMAC implementations,
and then confirmed with a Macchiatobin Single Shot connected to a
Clearfog: when MVPP2_GMAC_INBAND_AN_MASK is set, the clearfog does
not receive the advertised pause mode settings.

Lastly, there is no flow control in the in-band control word in Cisco
SGMII, setting the flow control autonegotiation bit even with a PHY
that has the Marvell extension to send this information does not result
in the flow control being enabled at the MAC.  We need to do this
manually using the information provided via phylink.

Re-code mvpp2's mac_config() and mac_link_up() to follow this pattern.
This allows Sven Auhagen's board and Macchiatobin to reliably bring
the link up with the 88e1512 PHY with phylink operating in PHY mode
with COMPHY built as a module but the rest of the networking built-in,
and u-boot having brought up the interface.  in-band mode requires an
additional patch to resolve another problem.
Tested-by: NSven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sven Auhagen reports that if he changes a SFP+ module for a SFP module
on the Macchiatobin Single Shot, the link does not come back up.  For
Sven, it is as easy as:

- Insert a SFP+ module connected, and use ping6 to verify link is up.
- Remove SFP+ module
- Insert SFP 1000base-X module use ping6 to verify link is up: Link
  up event did not trigger and the link is down

but that doesn't show the problem for me.  Locally, this has been
reproduced by:

- Boot with no modules.
- Insert SFP+ module, confirm link is up.
- Replace module with 25000base-X module.  Confirm link is up.
- Set remote end down, link is reported as dropped at both ends.
- Set remote end up, link is reported up at remote end, but not local
  end due to lack of link interrupt.

Fix this by setting up both GMAC and XLG interrupts for port 0, but
only unmasking the appropriate interrupt according to the current mode
set in the mac_config() method.  However, only do the mask/unmask
dance when we are really changing the link mode to avoid missing any
link interrupts.
Tested-by: NSven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the phy_interface_mode_is_8023z() helper for detecting interface
modes that use 802.3z serial encoding.  This is equivalent to testing
for both 1000base-X and 2500base-X.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.

This change was generated with the following Coccinelle SmPL patch:

@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@

-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLuis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: NChristoph Hellwig <hch@lst.de>

When acpi_match_device fails, its return value is NULL. Directly using
the return value without a check may result in a NULL-pointer
dereference. The fix checks if acpi_match_device fails, and if so,
returns -EINVAL.
Signed-off-by: NKangjie Lu <kjlu@umn.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvpp2_phylink_validate() sets all modes that are supported by a
given PPv2 port. An mistake made the 10000baseT_Full mode being
advertised in some cases when a port wasn't configured to perform at
10G. This patch fixes this.

Fixes: d97c9f4a ("net: mvpp2: 1000baseX support")
Reported-by: NRussell King <linux@armlinux.org.uk>
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvpp2_phylink_validate() function sets all modes that are
supported by a given PPv2 port. A recent change made all ports to
advertise they support 10G modes in certain cases. This is not true,
as only the port #0 can do so. This patch fixes it.

Fixes: 01b3fd5a ("net: mvpp2: fix detection of 10G SFP modules")
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert mvebu-cp110-comphy PHY driver to use recently introduced
PHY_MODE_ETHERNET and phy_set_mode_ext().

Cc: Russell King - ARM Linux <linux@armlinux.org.uk>
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>

The .validate phylink callback should empty the supported bitmap when
the interface mode is invalid.

Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Reported-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvpp2_phylink_validate() relies on the interface field of
phylink_link_state to determine valid link modes. However, when called
from phylink_sfp_module_insert() this field in not initialized. The
default switch case then excludes 10G link modes. This allows 10G SFP
modules that are detected correctly to be configured at max rate of
2.5G.

Catch the uninitialized PHY mode case, and allow 10G rates.

Fixes: d97c9f4a ("net: mvpp2: 1000baseX support")
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvpp2 driver has the curious behaviour of passing a stack variable
to irq_set_affinity_hint(), which results in the kernel exploding
the first time anyone accesses this information. News flash: userspace
does, and irqbalance will happily take the machine down. Great stuff.

An easy fix is to track the mask within the queue_vector structure,
and to make sure it has the same lifetime as the interrupt itself.

Fixes: e531f767 ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When offloading the L3 and L4 csum computation on TX, we need to extract
the l3_proto from the ethtype, independently of the presence of a vlan
tag.

The actual driver uses skb->protocol as-is, resulting in packets with
the wrong L4 checksum being sent when there's a vlan tag in the packet
header and checksum offloading is enabled.

This commit makes use of vlan_protocol_get() to get the correct ethtype
regardless the presence of a vlan tag.

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit allows each TXQ to be picked in a round-robin fashion by
the PPv2 transmit scheduling mechanism. This is opposed to the default
behaviour that prioritizes the highest numbered queues.
Suggested-by: NYan Markman <ymarkman@marvell.com>
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the PPv2 controller has multiple TX queues, we can spread traffic
by assining TX queues to CPUs, allowing to use XPS to balance egress
traffic between CPUs.

Suggested-by : Yan Markman <ymarkman@marvell.com>
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>