This fixes the issue noted by Russell King:

drivers/mmc/host/omap_hsmmc.c: In function 'mmc_omap_xfer_done':
drivers/mmc/host/omap_hsmmc.c:301: error: implicit declaration of function 'mmc_omap_fclk_lazy_disable'

This got broken by 4a694dc9.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

SD/MMC card timeouts can be very high. So avoid busy-waiting,
using the scheduler. Calculate all timeouts in jiffies units,
because this will give us the correct sign when to involve
the scheduler.
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Some cards are not able to calculate a valid CRC16 value
for CID and CSD reads (CRC for 512 byte data blocks is OK).
By moving the CRC enable after the read of CID and CSD, these
cards can be used. This patch was tested with a faulty 8 GByte
takeMS Class 6 SDHC card. This patch was suggested by
Pierre Ossman.
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Spurious IRQs seen on MMC after 2.6.29.  Flush posted write in IRQ
handler.

The interrupt line is released by clearing the error status bits
in the MMCHS_STAT register, which must occur before the interrupt
handler returns to avoid unwanted irqs.  Hence the need to flush
the posted write.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Acked-by: NTony Lindgen <tony@atomide.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Signed-off-by: NPierre Ossman <pierre@ossman.eu>

DMA request source (RSSR) needs to be set only once (in probe).
DMA burst length (BLR) need to be set only in set_ios()

This cleans up imxmci_setup_data() and should make it a little
bit faster :)
Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Add __init __exit for appropriate probe and remove functions.
Conver to platform_driver_probe()
Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NJarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Glue between MMC and regulator stacks ... verified with
some OMAP3 boards using adjustable and configured-as-fixed
regulators on several MMC controllers.

These calls are intended to be used by MMC host adapters
using at least one regulator per host.  Examples include
slots with regulators supporting multiple voltages and
ones using multiple voltage rails (e.g. DAT4..DAT7 using a
separate supply, or a split rail chip like certain SDIO
WLAN or eMMC solutions).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMatt LaPlante <kernel1@cyberdogtech.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Cc: drzeus-mmc@drzeus.cx
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>

This fixes a bug when setting the sdc_reg for 4-bit bus width
transactions.
Signed-off-by: NHans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This patch adds a new driver: sdhci-of. The driver is similar to
the sdhci-pci, it contains common probe code, and controller-specific
ops and quirks.

So far there are only Freescale eSDHC ops and quirks.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

FSL eSDHC controllers can support maximum block size up to 4096 bytes,
the MBL (Maximum Block Length) field in the capabilities register
extended by one bit, and is set to 0x3.

But the SDHCI core doesn't support blocks of 4096 bytes, and thus
forces blksz to the lowest value -- 512 bytes. With this patch we can
pin up the blksz to the maximum supported block size, i.e. 2048 bytes.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

FSL eSDHC controllers losing signal/interrupt enable states after
reset, so we should re-enable them.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Small udelay is needed to make eSDHC work in PIO mode. Without
the delay reading causes endless interrupt storm, and writing
corrupts data. The first guess would be that we must wait for
some bit in some register, but I didn't find any reliable bits
that change before and after the delay.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

FSL eSDHC hosts have incompatible register map to manage the SDCLK.
This patch adds set_clock callback so that drivers could overwrite
set_clock behaviour.

Similar patch[1] was posted by Ben Dooks, though in Ben's version the
callback is named change_clock, plus the patch has some unrelated bits
that makes the patch difficult to reuse.

[1] http://lkml.org/lkml/2008/12/2/160Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Some controllers do not provide clock information in their capabilities
(in the Samsung case, it is because there are multiple clock sources
available to the controller). Add hooks to allow the system to supply
clock information.

p.s.
In the original Ben's patch there was a bug that makes sdhci_add_host()
return -ENODEV even if callbacks were specified. This is fixed now.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This patch adds SDHCI_QUIRK_INVERTED_WRITE_PROTECT quirk. When
specified, the sdhci driver will invert WP state.

p.s. Actually, the quirk is more board-specific than
     controller-specific.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This patch adds SDHCI_QUIRK_BROKEN_CARD_DETECTION quirk. When specified,
sdhci driver will set MMC_CAP_NEEDS_POLL MMC host capability, and won't
enable card insert/remove interrupts.

This is needed for hosts with unreliable card detection, such as FSL
eSDHC. The original eSDHC driver was tring to "debounce" card-detection
IRQs by reading present state and disabling particular interrupts. But
with this debouncing scheme I noticed that sometimes we miss card
insertion/removal events.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Some hosts (that is, FSL eSDHC) throw PIO interrupts during DMA
transfers, this causes tons of unneeded interrupts, and thus highly
degraded speed.

This patch modifies the driver so that now we only enable relevant
(DMA or PIO) interrupts during transfers.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Card detection interrupts should be handled separately as they should
not be enabled before mmc_add_host() returns and should be disabled
before calling mmc_remove_host(). The same is for suspend and resume
routines.

sdhci_init() no longer enables card-detection irqs. Instead, two new
functions implemented: sdhci_enable_card_detection() and
sdhci_disable_card_detection().

New sdhci_reinit() call implemented to behave the same way as the old
sdhci_init().

Also, this patch implements and uses few new helpers to manage IRQs in
a more conveinient way, that is:

- sdhci_clear_set_irqs()
- sdhci_unmask_irqs()
- sdhci_mask_irqs()
- SDHCI_INT_ALL_MASK constant

sdhci_enable_sdio_irq() converted to these new helpers, plus the
helpers will be used by the subsequent patches.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Currently the SDHCI driver works with PCI accessors (write{l,b,w} and
read{l,b,w}).

With this patch drivers may change memory accessors, so that we can
support hosts with "weird" IO memory access requirments.

For example, in "FSL eSDHC" SDHCI hardware all registers are 32 bit
width, with big-endian addressing. That is, readb(0x2f) should turn
into readb(0x2c), and readw(0x2c) should be translated to
le16_to_cpu(readw(0x2e)).
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Some cards are not able to send the data token in time, but
miss the time frame for some bits(!). So synchronize to the
start of the token.
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

It is necessary to wait for bus power before sending
any commands.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Data transfers on third OMAP3 MMC controller don't work
because DMA line numbers are only defined for MMC1 and MMC2.
Fix that and store line numbers in mmc_omap_host structure
to reduce code size.
Tested on OMAP3 pandora board.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Turn off the bus power at suspend.
Signed-off-by: NJarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Allow slot_name to be the same as the other OMAP
driver, by removing the redundant "slot:" prefix.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Allow a cover switch to be used to cause a rescan of the
MMC slot.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NJarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Instead of using the bounce buffer, using scatter-gather emulation
(as in the OMAP1/2 MMC driver) removes the need of one extra memory
copy and improves performance.
Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Some MMC commands result in the card becoming busy after
the response is received.  This needs to be specified
for the omap_hsmmc host controller, which is what this
patch does.  However, the effect is that some commands
with no data will cause a Transfer Complete (TC) interrupt
in addition to the Command Complete (CC) interrupt.
In order to deal with that, the irq handler has needed
a few changes also.

The benefit of this change is that the omap_hsmmc host
controller driver now waits for the TC interrupt while
the card is busy, so the mmc_block driver needs to poll
the card status just once instead of repeatedly.
i.e. the net result is more sleep and less cpu.

The command sequence for open-ended multi-block write
with DMA is now:

	Issue write command CMD25
	Receive CC interrupt
	Data is sent
	Receive TC interrupt (DMA is done)
	Issue stop command CMD12
	Receive CC interrupt
	Card is busy
	Receive TC interrupt
	Card is now ready for next transfer
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NJarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This supports MMC/SD/SDIO currently found on the Kirkwood 88F6281 and
88F6192 SoC controllers.
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

drivers/mmc/host/tmio_mmc.h: In function 'tmio_mmc_kmap_atomic':
drivers/mmc/host/tmio_mmc.h:147: error: implicit declaration of function 'kmap_atomic'
drivers/mmc/host/tmio_mmc.h:147: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
drivers/mmc/host/tmio_mmc.h: In function 'tmio_mmc_kunmap_atomic':
drivers/mmc/host/tmio_mmc.h:153: error: implicit declaration of function 'kunmap_atomic'
drivers/mmc/host/tmio_mmc.h:153: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Update the tmio_mmc code to call mmc_free_host() when
done using the private data. Without this fix the driver
frees memory and then keeps on using it as private data.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Update the tmio_mmc code to use resource_size(). With this
patch applied the correct resource size is passed to ioremap().
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Some SD cards have very high timeouts in SPI mode.
So adjust the timeouts from theory to practice.
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>