This patch removes the rval variable returns from function and replaces
them with direct returns in ixgbe_dcbnl_getnumtcs. It also changes how
ixgbe_gstrings_test is copied into data with memcpy in ixgbe_get_strings
because "*ixgbe_gstrings_test too small (32 vs 160)".
Signed-off-by: NJosh Hay <joshua.a.hay@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a default case which goes to the next loop iteration
in the case where p is not set, preventing p from being dereferenced.
Signed-off-by: NJosh Hay <joshua.a.hay@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds functions needed for reading SFF-8472 diagnostic data
from SFP modules.

Based on original patch from Aurélien Guillaume <footplus@gmail.com>

CC: Aurélien Guillaume <footplus@gmail.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Resolve the following strict checkpatch checks:
CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
CHECK:BRACES: Blank lines aren't necessary before a close brace '}'
CHECK:BRACES: braces {} should be used on all arms of this statement
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are enough register offsets to warrant being in their own header
file, and doing so logically separates them from other header file content.
They have been converted from an enumerated data type to #defines as is
done in all the other Intel wired ethernet drivers.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines, function prototypes and data types which are applicable to
all/most devices supported by the driver but are specific to the
manageability component of each device to the new manage.h header file.
These #defines, function prototypes and data types can be used by other
files in the driver and moving them to the manageability-specific file
makes it clearer to which component they are applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines and function prototypes which are applicable to all/most
devices supported by the driver and are specific to the NVM component of
each device to the new nvm.h header file.  These #defines and function
prototypes can be used by other files in the driver and moving them to the
NVM-specific file makes it clearer to which component they are applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines and function prototypes which are applicable to all/most
devices supported by the driver and are specific to the PHY component of
each device to the new phy.h header file.  These function prototypes can be
used by other files in the driver and moving them to the PHY-specific file
makes it clearer to which component they are applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move prototypes for functions which are applicable to all/most devices
supported by the driver and are specific to the MAC component of each
device to the new mac.h header file.  These function prototypes can be used
by other files in the driver and moving them to the MAC-specific file makes
it clearer to which component they are applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines and function prototypes specific to the ICH/PCH family of
devices (ICH8/82562, ICH8/82566, ICH8/82567, ICH9/82562, ICH9/82566,
ICH9/82567, ICH10/82567, 82577, 82578, 82579, I217, I218) to the new
ich8lan.h header file (the convention for Intel wired ethernet drivers is
to use the name of the first device in the family for related file and
function names).  These defines and function prototypes can be used by
other files in the driver and moving them to the ICH/PCH-family-specific
file makes it clearer to which devices they are applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines specific to the ESB2/82563 family of devices to the new
80003es2lan.h header file.  These defines can be used by other files in the
driver and moving them to the 80003es2lan-family-specific file makes it
clearer to which devices they are applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move #defines and function prototypes specific to the 8257x family of
devices (82571, 82572, 82573, 82574, 82583) to the new 82571.h header file
(the convention for Intel wired ethernet drivers is to use the name of the
first device in the family for related file and function names).  These
defines and function prototypes can be used by other files in the driver
and moving them to the 8257x-family-specific file makes it clearer to which
devices they are applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This module is namespace aware, netns_ok was just disabled by default
for sanity.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BUG: spinlock bad magic on CPU#1, swapper/0/1
lock: 0xbfae0f8c, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
Backtrace:
 [<80011d54>] (dump_backtrace+0x0/0x10c) from [<804e7800>] (dump_stack+0x18/0x1c)
 r6:bfae0000 r5:bfae0f8c r4:00000000 r3:806c1310
 [<804e77e8>] (dump_stack+0x0/0x1c) from [<804e9f20>] (spin_dump+0x80/0x94)
 [<804e9ea0>] (spin_dump+0x0/0x94) from [<804e9f60>] (spin_bug+0x2c/0x30)
 r5:805f6f8c r4:bfae0f8c
 [<804e9f34>] (spin_bug+0x0/0x30) from [<80257984>] (do_raw_spin_lock+0x170/0x1b0                                         )
 r5:806b4950 r4:bfae0f8c
 [<80257814>] (do_raw_spin_lock+0x0/0x1b0) from [<804ed15c>] (_raw_spin_lock_irqs                                         ave+0x18/0x20)
 [<804ed144>] (_raw_spin_lock_irqsave+0x0/0x20) from [<8033c694>] (fec_ptp_start_                                         cyclecounter+0x3c/0x120)
 r4:bfae0f8c r3:00000002
 [<8033c658>] (fec_ptp_start_cyclecounter+0x0/0x120) from [<80339e08>] (fec_resta                                         rt+0x56c/0x5f8)
 r8:00000000 r7:806e6f48 r6:00000112 r5:806b4950 r4:bfae0000
 [<8033989c>] (fec_restart+0x0/0x5f8) from [<8033b9e4>] (fec_probe+0x508/0xa48)
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case port is leaving the team, set the option "activeport" as changed
so the change can be properly propagated to userspace
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In team_port_del(), there is need to be do all the cleanup related
things first and netlink event notifiers should be called after that.
This fixes two problems:
team carrier is now correctly set (port is removed from list first)
mode can set option as changed in .port_leave op
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Essentially do the same thing with port list as with option list.
Multipart netlink message.
Side effect is that port event message can send port which is not longer
in team->port_list.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip_eth_mc_map function can't be used when CONFIG_INET isn't defined.
Fixed compilation error by adding CONFIG_INET define check before using the
function.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Propagate return value of mlx4_en_ethtool_add_mac_rule_by_ipv4 in case of
failure.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the loop, don't check 'rv' twice in a row. Without the loop, 'rv'
doesn't even need to be checked.

Make the comment more grammar-friendly.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As in del_timer() there has already placed a timer_pending() function
to check whether the timer to be deleted is pending or not, it's
unnecessary to check timer pending state again before del_timer() is
called.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, when the PF driver is unloaded and re-loaded while VFs are attached
to VMs, it loses control of its VFs.

The PF driver now uses the newly defined/created GET_IFACE_LIST cmd
(available in FW ver >= 4.6) to query the if_id of the VFs
(enabled in its previous life). The PF driver then uses the if_id for
further VF configuration.

The GET_IFACE_MAC_LIST cmd has also implemented in BE3 FW for PF to
query pmac-ids used by its VFs.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc failures already get standardized OOM
messages and a dump_stack.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc failures already get standardized OOM
messages and a dump_stack.

Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Remove now unused variables.
Remove unnecessary memset after kzalloc->kcalloc.
Whitespace cleanups for these changes.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc failures already get standardized OOM
messages and a dump_stack.

Convert kzalloc's with multiplies to kcalloc.
Remove now unused size variables.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc failures already get standardized OOM
messages and a dump_stack.

Hoist assigns from if tests.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc failures already get standardized OOM
messages and a dump_stack.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc failures already get standardized OOM
messages and a dump_stack.

Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc failures already get standardized OOM
messages and a dump_stack.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc failures already get standardized OOM
messages and a dump_stack.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems due to RCU usage, i.e. within SCTP's address binding list,
a, say, ``behavioral change'' was introduced which does actually
not conform to the RFC anymore. In particular consider the following
(fictional) scenario to demonstrate this:

  do:
    Two SOCK_SEQPACKET-style sockets are opened (S1, S2)
    S1 is bound to 127.0.0.1, port 1024 [server]
    S2 is bound to 127.0.0.1, port 1025 [client]
    listen(2) is invoked on S1
    From S2 we call one sendmsg(2) with msg.msg_name and
       msg.msg_namelen parameters set to the server's
       address
    S1, S2 are closed
    goto do

The first pass of this loop passes successful, while the second round
fails during binding of S1 (address still in use). What is happening?
In the first round, the initial handshake is being done, and, at the
time close(2) is called on S1, a non-graceful shutdown is performed via
ABORT since in S1's receive queue an unprocessed packet is present,
thus stating an error condition. This can be considered as a correct
behavior.

During close also all bound addresses are freed, thus nothing *must*
be active anymore. In reference to RFC2960:

  After checking the Verification Tag, the receiving endpoint shall
  remove the association from its record, and shall report the
  termination to its upper layer. (9.1 Abort of an Association)

Also, no half-open states are supported, thus after an ungraceful
shutdown, we leave nothing behind. However, this seems not to be
happening though. In a real-world scenario, this is exactly where
it breaks the lksctp-tools functional test suite, *for instance*:

  ./test_sockopt
  test_sockopt.c  1 PASS : getsockopt(SCTP_STATUS) on a socket with no assoc
  test_sockopt.c  2 PASS : getsockopt(SCTP_STATUS)
  test_sockopt.c  3 PASS : getsockopt(SCTP_STATUS) with invalid associd
  test_sockopt.c  4 PASS : getsockopt(SCTP_STATUS) with NULL associd
  test_sockopt.c  5 BROK : bind: Address already in use

The underlying problem is that sctp_endpoint_destroy() hasn't been
triggered yet while the next bind attempt is being done. It will be
triggered eventually (but too late) by sctp_transport_destroy_rcu()
after one RCU grace period:

  sctp_transport_destroy()
    sctp_transport_destroy_rcu() ----.
      sctp_association_put() [*]  <--+--> sctp_packet_free()
        sctp_association_destroy()          [...]
          sctp_endpoint_put()                 skb->destructor
            sctp_endpoint_destroy()             sctp_wfree()
              sctp_bind_addr_free()               sctp_association_put() [*]

Thus, we move out the condition with sctp_association_put() as well as
the sctp_packet_free() invocation and the issue can be solved. We also
better free the SCTP chunks first before putting the ref of the association.

With this patch, the example above (which simulates a similar scenario
as in the implementation of this test case) and therefore also the test
suite run successfully through. Tested by myself.

Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

reduce the permission check of bond device's ioctl.
allow the userns root to control the bond device.
Signed-off-by: NGao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

since the mdb table is belong to bridge device,and the
bridge device can only be seen in one netns.
So it's safe to allow unprivileged user which is the
creator of userns and netns to modify the mdb table.
Signed-off-by: NGao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ebt_table is a private resource of netns, operating ebtables
in one netns will not affect other netns, we can allow the
creator user of userns and netns to change the ebtables.
Signed-off-by: NGao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Right now,only ixgdb,macvlan,vxlan and bridge implement
fdb_add/fdb_del operations.

these operations only operate the private data of net
device. So allowing the unprivileged users who creates
the userns and netns to add/del fdb entries will do no
harm to other netns.
Signed-off-by: NGao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If stmmac_dvr_probe() fails in stmmac_pci_probe(), it breaks off initialization,
deallocates all resources, but returns zero.
The patch adds -ENODEV as return value in this case.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Paul Gortmaker says:

====================
The removal of wanrouter code was originally listed in the (now
gone) feature removal file since May 2012, and an RFC of the
deletion was posted[1] in late 2012.  The overall concept was given
an OK, but defconfig contamination, build failures, etc. meant that
it didn't quite make it into mainline for 3.8.

Since that time, Dan discovered (via code audit) a runtime bug that
proves nobody has been using this for over four years[2].  With that
new information, I think it makes sense for someone to follow through
on Joe's original RFC and get this done for the 3.9 release.

In addition to resolving the build failures of the RFC by keeping
stub headers, this also splits the change into two parts, just like
the token ring removal did.  Part #1 decouples the mainline kernel
from the expired subsystem, and part #2 does the large scale
deletion of the subsystem content.

The advantage of the above, is that a "git blame" will never lead
you to a 4000+ line deletion commit.  The large scale deletion will
never show up in a "git blame" and hence the same advantages that we
get from the "--irreversible-delete" in the review stage of "git
format-patch" are also embedded into the git history itself.  This
may seem like a moot point to some, but for those who spend a
considerable amount of time data mining in the git history, this is
probably worth doing.

I have done build tests of all[mod/yes]config for both the stage 1
(Makefile and Kconfig) and stage 2 (full driver delete) as a sanity
check, and the issues with the previously posted RFC should be gone.

Speaking of "--irreversible-delete" -- these patches were created
with that option, so if you want to use them locally, you are going
to have to pull (location below) the content instead of doing a
"git am" of the mailed out content.

[1] http://patchwork.ozlabs.org/patch/198794/
[2] http://www.spinics.net/lists/netdev/msg218670.html
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We actually store the MAC address as well as the board_name here.  The
longest board_name is 75 characters so there is more than enough room
to hold the 17 character MAC and the ": " divider.  But making this
buffer larger silences a static checker warning.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-By: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>