Notice by Fengguang Wu's automatic sparse checker.
Reported-by: NFengguang Wu <wfg@linux.intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The previous patch put all the code, and handlers in place. It should
now be safe to enable the parity error interrupt. The parity error must
be unmasked in both the GTIMR, and the CS IMR. Unfortunately, the docs
aren't clear about this; nevertheless it's the truth.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On IVB hardware we are given an interrupt whenever a L3 parity error
occurs in the L3 cache. The L3 cache is used by internal GPU clients
only.  This is a very rare occurrence (in fact to test this I need to
use specially instrumented silicon).

When a row in the L3 cache detects a parity error the HW generates an
interrupt. The interrupt is masked in GTIMR until we get a chance to
read some registers and alert userspace via a uevent. With this
information userspace can use a sysfs interface (follow-up patch) to
remap those rows.

Way above my level of understanding, but if a given row fails, it is
statistically more likely to fail again than a row which has not failed.
Therefore it is desirable for an operating system to maintain a lifelong
list of failing rows and always remap any bad rows on driver load.
Hardware limits the number of rows that are remappable per bank/subbank,
and should more than that many rows detect parity errors, software
should maintain a list of the most frequent errors, and remap those
rows.

V2: Drop WARN_ON(IS_GEN6) (Jesse)
DRM_DEBUG row/bank/subbank on errror (Jesse)
Comment updates (Jesse)
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Note that gen3 is the only platform where we've got the bit
definitions right, hence the workaround of disabling sdvo hotplug
support on i945g/gm is not due to misdiagnosis of broken hotplug irq
handling ...
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: add some blurb about sdvo hotplug fail on i945g/gm I've
wondered about while reviewing.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Also as we set the HOTPLUG_EN to 0 during pre-install, we can simply set
it during post-install, and nor do we wish to enable unwanted hotplug
events.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In many places we wish to iterate over the rings associated with the
GPU, so refactor them to use a common macro.

Along the way, there are a few code removals that should be side-effect
free and some rearrangement which should only have a cosmetic impact,
such as error-state.

Note that this slightly changes the semantics in the hangcheck code:
We now always cycle through all enabled rings instead of
short-circuiting the logic.

v2: Pull in a couple of suggestions from Ben and Daniel for
intel_ring_initialized() and not removing the warning (just moving them
to a new home, closer to the error).
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
[danvet: Added note to commit message about the small behaviour
change, suggested by Ben Widawsky.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Haswell interrupts are mostly similar with Ivy Bridge, so we share same
routines with it.

This patch also simplifies the vblank counter handling for all the Gen5+
architectures.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We can take advantage that the PCH_IIR is a subordinate register to
reduce one of the required IIR reads, and that we only need to clear
interrupts handled to reduce the writes. And by simply tidying the code
we can reduce the line count and hopefully make it more readable.

v2: Split out the bugfix from the refactoring.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently the code re-reads PCH_IIR during the hotplug interrupt
processing. Not only is this a wasted read, but introduces a potential
for handling a spurious interrupt as we then may not clear all the
interrupts processed (since the re-read IIR may contains more interrupts
asserted than we clear using the result of the original read).
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Only half of them even cared, and it's always the same one.
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

- reduce the irq disabled section, even for a debugfs file this was
  way too long.
- always disable irqs when taking the lock.

v2: Thou shalt not mistake locking for reference counting, so:
- reference count the error_state to protect from concurent freeeing.
  This will be only really used in the next patch.
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... and hide it in i915_dma.c.

This way all the legacy stuff dealing with READ_BREADCRUMB and
LP_RING and friends is in i915_dma.c.

v2: Rebase on top of Chris Wilson's rework irq handling code.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Let's just get this out of the way.

v2: Rebase against ENODEV changes.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We never supported dri1 on gen5+.

VLV never had that code, so no need to remove it.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

i915_dma.c contains most of the old dri1 horror-show, so move
the remaining bits there, too. The code has been removed and
the only thing left are some stubs to ensure that userspace
doesn't try to use this stuff. vblank_pipe_set only returns 0
without any side-effects, so we can even stub it out with
the canonical drm_noop.

v2: Rebase against ENODEV changes.
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

vblank_pipe was intended to be used for tracking DRI1 state. However,
the vblank_pipe reported to DRI1 is fixed to umask both pipes, and the
dev_priv->vblank_pipe unused and superfluous.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The waiting_seqno is not terribly useful, and as such we can remove it
so that we'll be able to extract lockless code.

v2: Keep the information for error_state (Chris)
Check if ring is initialized in hangcheck (Chris)
Capture the waiting ring (Chris)
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
[danvet: add some bikeshed to clarify a comment.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This extra bit of interrupt enabling code doesn't belong in the wait
seqno function. If anything we should pull it out to a helper so the
throttle code can also use it. The history is a bit vague, but I am
going to attempt to just dump it, unless someone can argue otherwise.

Removing this allows for a shared lock free wait seqno function. To keep
tabs on this issue though, the IER value is stored on error capture
(recommended by Chris Wilson)

v2: fixed typo EIR->IER (Ben)
Fix some white space (Ben)
Move IER capture to globally instead of per ring (Ben)
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
[danvet: ier is a 16 bit reg on gen2!]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since there is only one remaining user of I915_INTERRUPT_ENABLE_FIX,
expand it at the callsite. Quoting Jesse Barnes:

"I'd really like to get rid of these defines at the top of i915_irq.c.
Some are unused and the others just make you check for the right bits
everytime your read the code."
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add bikeshed suggested by Jesse.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We appear to allow too many pending pageflips as evidenced by an
apparent pin-leak. So borrow the pageflip completion logic from i8xx for
handling PendingFlip in a robust manner.

v2: Address Jesse's reminders about the nuances of gen3 IRQ handling.

References: https://bugzilla.kernel.org/show_bug.cgi?id=41882Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Bring the for-each-pipe loops together so that the code is easier on the
eyes.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A couple of miscellaneous cleanups as well to move per-loop condition
variables within the scope of the loop and the update of the DRI1
breadcrumb to the tail of the function.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And a couple of miscellaneous cleanups to the main body of the IRQ loop;
move per-loop condition variables within the scope of the loop and move
the old DRI1 breadcrumb to the tail of the function and so only execute
it once.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On later gen3, you are able to select the meaning of the FlipPending
status bit in IIR and change it to FlipDone. This was sometimes done by
the BIOS leading to confusion on just how pageflipping worked on gen3.
Simplify the implementation by using the legacy meaning for all gen3
machines.

Note: this makes all gen3 machines equally broken...
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In preparation for rewriting the gen3 irq handler.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And remove the cargo-culted copy from the valleyview irq handler.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The waitqueues are already initialised during ring initialisation so
kill the redundant and duplicated code to do so in each generations IRQ
installer.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Rather than duplicate similar code across the IRQ installers, perform
the initialisation of the workers upfront. This will lead to simpler
teardown and quiescent code as we can assume that the workers have
been initialised.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Calling these when gem assumes full control of the hw won't end
in anything else than tears. So be a bit more paranoid here.

Just serves as documentation.

v2: Bail out with ENODEV as suggested by Chris Wilson.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Simplify object tracking by removing the inactive but pinned list. The
only place where this was used is for counting the available memory,
which is just as easy performed by checking all objects on the rare
occasions it is required (application startup). For ease of debugging,
we keep the reporting of pinned objects through the error-state and
debugfs.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... and put them to so good use.

Note that there's functional change in vlv clock gating code, we now
no longer spuriously read back the current value of the bit. According
to Bspec the high bits should always read zero, so ORing this in
should have no effect.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

gen2 hardware has some significant differences from the other interrupt
routines that were glossed over and then forgotten about in the
transition to KMS. Such as

- 16bit IIR
- PendingFlip status bit

This patch reintroduces a handler specifically for gen2 for the purpose
of handling pageflips correctly, simplifying code in the process.

v2: Also fixup ring get/put irq to only access 16bit registers (Daniel)

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24202
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41793Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: use posting_read16 in intel_ringbuffer.c and kill _driver
from the function names.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The purpose of this patch is to avoid zeroing the lower 12 reserved bits
of surface base address registers (framebuffer & sprite).  There are bits
in that range that may occasionally be set by BIOS or by other components.
Signed-off-by: NArmin Reese <armin.c.reese@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This function, along with the registers and deferred work hander, are
all shared with SandyBridge, IvyBridge and their variants. So remove the
duplicate code into a single function.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On the first instance we just wish to kick the waiters and see if that
terminates the wait conditions. If it does not, then we do not want to
keep retrying without ever making any forward progress and becoming
stuck in a hangcheck loop.
Reported-and-tested-by: NLukas Hejtmanek <xhejtman@fi.muni.cz>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48209Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It exists way back to gen2, bug got moved around on gen4 a bit.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>