Provide new implementation infrastructure that platforms may choose to use
when implementing the GPIO programming interface.  Platforms can update their
GPIO support to use this.  In many cases the incremental cost to access a
non-inlined GPIO should be less than a dozen instructions, with the memory
cost being about a page (total) of extra data and code.  The upside is:

  * Providing two features which were "want to have (but OK to defer)" when
    GPIO interfaces were first discussed in November 2006:

    -	A "struct gpio_chip" to plug in GPIOs that aren't directly supported
	by SOC platforms, but come from FPGAs or other multifunction devices
	using conventional device registers (like UCB-1x00 or SM501 GPIOs,
	and southbridges in PCs with more open specs than usual).

    -	Full support for message-based GPIO expanders, where registers are
	accessed through sleeping I/O calls.  Previous support for these
	"cansleep" calls was just stubs.  (One example: the widely used
	pcf8574 I2C chips, with 8 GPIOs each.)

  * Including a non-stub implementation of the gpio_{request,free}() calls,
    making those calls much more useful.  The diagnostic labels are also
    recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot
    of all GPIOs known to this infrastructure.

The driver programming interfaces introduced in 2.6.21 do not change at all;
this infrastructure is entirely below those covers.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add an empty drivers/gpio directory for gpiolib infrastructure and GPIO
expanders.  It will be populated by later patches.

This won't be the only place to hold such gpio_chip code.  Many external chips
add a few GPIOs as secondary functionality (such as MFD drivers) and platform
code frequently needs to closely integrate GPIO and IRQ support.

This is placed *early* in the build/link sequence since it's common for other
drivers to depend on GPIOs to do their work, so they must be initialized early
in the device_initcall() sequence.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is a one-line patch to add the following to __scsi_alloc_queue():

dma_set_seg_boundary(dev, shost->dma_boundary);

This is the simplest approach but the result looks odd,
__scsi_alloc_queue() does:

blk_queue_segment_boundary(q, shost->dma_boundary);
dma_set_seg_boundary(dev, shost->dma_boundary);
blk_queue_max_segment_size(q, dma_get_max_seg_size(dev));

I think that it would be better to set up segment boundary in the same
way as we did for the maximum segment size. That is, removing
shost->dma_boundary and LLDs call pci_set_dma_seg_boundary (or its
friends).

Then __scsi_alloc_queue() can set up both limits in the same way:

blk_queue_segment_boundary(q, dma_get_seg_boundary(dev));
blk_queue_max_segment_size(q, dma_get_max_seg_size(dev));

killing dma_boundary in scsi_host_template needs a large patch for
libata (dma_boundary is used by only libata and sym53c8xx). I'll send
a patch to do that if it is acceptable. James and Jeff?
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds PCI's accessor for segment_boundary_mask in device_dma_parameters.

The default segment_boundary is set to 0xffffffff, same to the block layer's
default value (and the scsi mid layer uses the same value).
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This sets the segment size limit properly via pci_set_dma_max_seg_size
and remove blk_queue_max_segment_size because scsi-ml calls it.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: NJens Axboe <jens.axboe@oracle.com>
Acked-by: N"Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This sets the segment size limit properly via pci_set_dma_max_seg_size
and remove blk_queue_max_segment_size because scsi-ml calls it.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

request_queue and device struct must have the same value of a segment
size limit. This patch adds blk_queue_segment_boundary in
__scsi_alloc_queue so LLDs don't need to call both
blk_queue_segment_boundary and set_dma_max_seg_size. A LLD can change
the default value (64KB) can call device_dma_parameters accessors like
pci_set_dma_max_seg_size when allocating scsi_host.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NJeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch makes iommu respect segment size limits when merging sg
lists.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: NJens Axboe <jens.axboe@oracle.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: NGrant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds struct device_dma_parameters in struct pci_dev and properly
sets up a pointer in struct device.

The default max_segment_size is set to 64K, same to the block layer's
default value.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Mostly-acked-by: NJeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The clock to generate the desired baudrate with the MPSC is first divided
by the Baud Rate Generator (BRG) and then by the MPSC itself.  So, when the
BRG divider is changed, the MPSC divider must also be changed to generate
the correct baudrate.  During MPSC initialization, the BRG divider is
changed but the MPSC divider isn't changed until much later.  This results
in some printk's coming out garbled.  To fix that, set the MPSC divider at
the same time that the BRG divider is changed.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Coding style tweaks and printk levels.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Invalid speeds are forced to 9600. Update the code for this to encode new
style baud rates properly.
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some ports seem to be unable to drain their transmitters on shut down.  Such a
problem can occur if the port is programmed for hardware imposed flow control,
characters are in the FIFO but the CTS signal is inactive.

Normally, this isn't a problem because most places where we wait for the
transmitter to drain have a time-out.  However, there is no timeout in the
suspend path.

Give a port 30ms to drain; this is an arbitary value chosen to avoid long
delays if there are many such ports in the system, while giving a reasonable
chance for a single port to drain.  Should a port not drain within this
timeout, issue a warning.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When we boot, serial ports remain in low power mode until they're used either
by userspace or for the kernel console.

However, if you suspend the system, and then resume, all serial ports will be
taken out of low power mode.  This is bad news for embedded devices where this
can mean higher power consumption.

Only bring a serial port out of low power mode if the port is being used as
the kernel console, or is in use by userspace.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow the private_data field to be specified in platform_data for the
standard 8250/16550 UART.  This field is used by DW APB type UARTs and
without this patch it's only possible to set this field when registering
the port by hand.  If private_data is not set then the driver will
potentially oops with a NULL pointer dereference.
Signed-off-by: NWill Newton <will.newton@gmail.com>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add ADDI-DATA GmbH communication cards to 8250_pci driver.  Supported cards
are:

APCI-7300, APCI-7420, APCI-7500, APCI-7800 APCI-7300-2, APCI-7420-2,
APCI-7500-2 APCI-7300-3, APCI-7420-3, APCI-7500-3, APCI-7800-3

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NKrauth J. <krauth.julien@addi-data.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove dead config symbol.
Signed-off-by: NJiri Olsa <olsajiri@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Dooks <ben@fluff.org>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

with reverting "x86, serial: convert legacy COM ports to platform devices",
we will have the serial console before the port is probled again.

uart_add_one_port==>uart_configure_port==>set_mcttrl(port, 0) will clear
the DTR setting by uart_set_options().  then I will lose my output from
serial console again.

So try to keep DTR in uart_configure_port()
Signed-off-by: NYinghai Lu <yinghai.lu@sun.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

pci_get_slot does a pci_dev_get, so pci_dev_put needs to be called in an
error case.

An extract of the semantic match used to find the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
type find1.T,T1,T2;
identifier find1.E;
statement find1.S;
expression x1,x2,x3;
expression find1.test;
int ret != 0;
@@

  T E;
  ...
(
* E = pci_get_slot(...);
  if (E == NULL) S
|
* if ((E = pci_get_slot(...)) == NULL)
  S
)
  ... when != pci_dev_put(...,(T1)E,...)
      when != if (E != NULL) { ... pci_dev_put(...,(T1)E,...); ...}
      when != x1 = (T1)E
      when != E = x3;
      when any
  if (test) {
    ... when != pci_dev_put(...,(T2)E,...)
        when != if (E != NULL) { ... pci_dev_put(...,(T2)E,...); ...}
        when != x2 = (T2)E
(
*   return;
|
*   return ret;
)
  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

of_iomap calls ioremap, and so should be matched with an iounmap.  At the
two error returns, the result of calling of_iomap is only stored in a local
variable, so these error paths need to call iounmap.  Furthermore, this
function ultimately stores the result of of_iomap in an array that is local
to the file.  These values should be iounmapped at some point.  I have
added a corresponding call to iounmap at the end of the function
m8xx_remove.

The problem was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
type T,T1,T2;
identifier E;
statement S;
expression x1,x2,x3;
int ret;
@@

  T E;
  ...
* E = of_iomap(...);
  if (E == NULL) S
  ... when != iounmap(...,(T1)E,...)
      when != if (E != NULL) { ... iounmap(...,(T1)E,...); ...}
      when != x1 = (T1)E
      when != E = x3;
      when any
  if (...) {
    ... when != iounmap(...,(T2)E,...)
        when != if (E != NULL) { ... iounmap(...,(T2)E,...); ...}
        when != x2 = (T2)E
(
*   return;
|
*   return ret;
)
  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update the AT91 CF driver to use the generic GPIO calls instead of the
AT91-specific ones; and request exclusive use of those signals.

Minor tweaks to cleanup code paths: always in reverse order of how the
resources were allocated, with remove() matching the fault paths of
probe().
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixing:
  CHECK   drivers/net/pcmcia/pcnet_cs.c
drivers/net/pcmcia/pcnet_cs.c:523:15: warning: symbol 'hw_info' shadows an earlier one
drivers/net/pcmcia/pcnet_cs.c:148:18: originally declared here
Signed-off-by: NRichard Knutsson <ricknu-0@student.ltu.se>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixing:
  CHECK   drivers/net/pcmcia/fmvj18x_cs.c
drivers/net/pcmcia/fmvj18x_cs.c:1205:6: warning: symbol 'i' shadows an earlier one
drivers/net/pcmcia/fmvj18x_cs.c:1179:9: originally declared here
Signed-off-by: NRichard Knutsson <ricknu-0@student.ltu.se>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use 'max(x,y)' instead of 'x < y ? y : x'.
Signed-off-by: NRichard Knutsson <ricknu-0@student.ltu.se>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixing:
  CHECK   drivers/net/pcmcia/axnet_cs.c
drivers/net/pcmcia/axnet_cs.c:994:5: warning: symbol 'ax_close' was not declared. Should it be static?
drivers/net/pcmcia/axnet_cs.c:1017:6: warning: symbol 'ei_tx_timeout' was not declared. Should it be static?
Signed-off-by: NRichard Knutsson <ricknu-0@student.ltu.se>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixing:
  CHECK   drivers/net/pcmcia/3c574_cs.c
drivers/net/pcmcia/3c574_cs.c:695:7: warning: symbol 'i' shadows an earlier one
drivers/net/pcmcia/3c574_cs.c:636:6: originally declared here
Signed-off-by: NRichard Knutson <ricknu-0@student.ltu.se>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- Print the invalid CIS filename in the invalid filename message.
- Use sizeof() instead of hard-coded constant for buffer size.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This stops the pcmcia core from using dev->power.power_state; that field is
deprecated (overdue for removal) and the only reason to update it was to make
the /sys/devices/.../power/state files (now removed) work better.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove kio_addr_t, and replace it with unsigned int.  No known architecture
needs more than 32 bits for IO addresses and ports and having a separate type
for it is just messy.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert the io_req_t members to unsigned int, to allow use on machines with
more than 16 bits worth of IO ports (i.e.  secondary busses on ppc64, etc).

There was only a couple of places in drivers where a change was needed.  I
left printk formats alone (there are lots of %04x-style formats in there),
mostly to not change the format on the platforms that only have 16-bit io
addresses, but also because the padding doesn't really add all that much value
most of the time.

I found only one sprintf of an address, and upsized the string accordingly (I
doubt anyone will have anywhere near INT_MAX as irq value, but at least
there's room for it now).
Signed-off-by: NOlof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

m68k:

drivers/net/wireless/b43/main.c:251: error: implicit declaration of function 'mmiowb'

Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Drivers that register a ->fault handler, but do not range-check the
offset argument, must set VM_DONTEXPAND in the vm_flags in order to
prevent an expanding mremap from overflowing the resource.

I've audited the tree and attempted to fix these problems (usually by
adding VM_DONTEXPAND where it is not obvious).
Signed-off-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit c9f6d3d5 ("[POWERPC] adb: Replace
sleep notifier with platform driver suspend/resume hooks") introduced
compile errors on m68k because <linux/platform_device.h> is not
explicitly included.  On powerpc, it's pulled in through <asm/prom.h>.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently early kernel messages, i.e., those from uncompression, go to the
debugging UART. And if it is enabled in the platform configuration, but
not initialized by the bootloader, the machine hangs, waiting for UART
status change. Besides, having those messages on another UART - typically
the console UART - may be preferrable. This patch allows selecting the
UART in kernel configuration.
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Warning message :
WARNING: vmlinux.o(.text+0x9afc): Section mismatch: reference to .init.text:sa1110_mb_enable (between 'sa1111_probe' and 'sa1111_remove')
WARNING: vmlinux.o(.text+0x13b1ac): Section mismatch: reference to .init.text:pcmcia_jornada720_init (between 'pcmcia_probe' and 'pcmcia_remove')

* fixes the 'section mismatch' building warnings for target sa1100. Solution is __init -> __devinit. Thanks to Randy Dunlap for pointing out the solution.
Signed-off-by: NKristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

drivers/serial/21285.c: In function 'serial21285_set_termios':
drivers/serial/21285.c:280: error: 'tty' undeclared (first use in this function)
drivers/serial/21285.c:280: error: (Each undeclared identifier is reported only once
drivers/serial/21285.c:280: error: for each function it appears in.)
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

After discussions with Anthony Liguori, it seems that the virtio
balloon can be made even simpler.  Here's my attempt.

The device configuration tells the driver how much memory it should
take from the guest (ie. balloon size).  The guest feeds the page
numbers it has taken via one virtqueue.

A second virtqueue feeds the page numbers the driver wants back: if
the device has the VIRTIO_BALLOON_F_MUST_TELL_HOST bit, then this
queue is compulsory, otherwise it's advisory (and the guest can simply
fault the pages back in).

This driver can be enhanced later to deflate the balloon via a
shrinker, oom callback or we could even go for a complete set of
in-guest regulators.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

As Avi pointed out, as we continue to massage the virtio PCI ABI, we can make
things a little more friendly to users by utilizing the PCI revision field to
indicate which version of the ABI we're using.  This is a hard ABI version
and incrementing it will cause the guest driver to break.

This is the necessary changes to virtio_pci to support this.
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

This is a PCI device that implements a transport for virtio.  It allows virtio
devices to be used by QEMU based VMMs like KVM or Xen.
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Am Freitag, 1. Februar 2008 schrieb Christian Borntraeger:
> Right. I will fix that with an additional patch.

This patch goes on top of the minor number patch. Please let me know if
you want a merged patch:

Currently virtio_blk creates the disk name combinging "vd"  with 'a'++.
This will give strange names after vdz. I have implemented names up to
vdzzz - inspired by the sd.c code. That should be sufficient for now.

There is one driver in the kernel (driver/s390/block/dasd_genhd.c) that
implements names from dasda-dasdzzzz allowing even more disks. Maybe
a janitor can come up with a common implementation usable for all kind
of block device drivers.

I have tested this patch with 100 disks - seems to work.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>