This is a cleanup patch and moves min/step voltages in a common samsung
header file so that they can be used by other s2mpxxx PMIC drivers. Only
few required macros are added currently and others can be added if needed.
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NAmit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

This driver also supports S2MPU02 now, thus update module description and
Kconfig accordingly.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch add S2MPU02 regulator device to existing S2MPS11 device driver
because of little difference between S2MPS1x and S2MPU02. The S2MPU02
regulator device includes LDO[1-28] and BUCK[1-7].
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
[Add missing linear_min_sel of S2MPU02 LDO regulators by Jonghwa Lee]
Signed-off-by: NJonghwa Lee <jonghwa3.lee@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NMark Brown <broonie@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

S2MPS11 supports enabling/disabling ramp delay only for buck[2346].
Other bucks have ramp delay enabled always.

However the bit shift for enabling buck6 ramp delay in register is equal
to 0. When ramp delay was set for the bucks unsupporting enable/disable
(buck[15789] and buck10), the ramp delay for buck6 was also enabled.

Fixes: b96244fa ("regulator: s2mps11: Don't check enable_shift before setting enable ramp rate")
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

GPIO 0 is a valid GPIO so allow using it as external control for
S2MPS14 regulators.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add support for external control over GPIO for LDO10, LDO11 and LDO12
S2MPS14 regulators. External control can be turned on by writing 0x0 to
control register which in case of other regulators is used for disabling
them. These LDO10-LDO12 regulators can be disabled only by I2C GPIO or
PWREN pin so the patch actually allows proper way of disabling them.

Additionally the GPIO control has two benefits:
 - It is faster than toggling it over I2C bus.
 - It allows disabling the regulator during suspend to RAM; The AP will
   enable it during resume.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Refactor code for parsing DTS to increase a little code readability. The
behaviour should not change.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current code misses updating the register when enable_shift is 0.
e.g. S2MPS11_BUCK9_RAMP_SHIFT and S2MPS11_BUCK6_RAMP_EN_SHIFT are 0.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add of_node_put to decrement the ref count.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

S2MPS14 regulators support suspend mode where their status is controlled
by PWREN coming from SoC. This patch implements the set_suspend_disable
for S2MPS14 regulators.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add support for S2MPS14 PMIC regulators to s2mps11 driver. The S2MPS14
has fewer BUCK-s and LDO-s than S2MPS11. It also does not support
controlling the BUCK ramp delay.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Reviewed-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Remove __initconst from regulator_desc array because this array is used
during probe and s2mps11_pmic_probe() is not in __init section. However
still select the number of supported regulators according to device ID
so the driver will be ready for adding support for S2MPS14 device.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add __initconst to 'regulator_desc' array with supported regulators.
During probe choose how many and which regulators will be supported
according to device ID. Then copy the 'regulator_desc' array to
allocated memory so the regulator core can use it.

Additionally allocate array of of_regulator_match() dynamically (based
on number of regulators) instead of allocation on the stack.

This is needed for supporting different devices in s2mps11
driver and actually prepares the regulator driver for supporting the
S2MPS14 device.

Code for supporting the S2MPS14 device will add its own array of
'regulator_desc' (also marked as __initconst). This way memory footprint
of the driver will be reduced (approximately 'regulators_desc' array for
S2MPS11 occupies 5 kB on 32-bit ARM, for S2MPS14 will occupy 3 kB).
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Cc: Yadwinder Singh Brar <yadi.brar01@gmail.com>
Reviewed-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Constify the regulator_desc 'regulators' array.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Regulators registered by devm_regulator_register() do not have to be
stored in state container because they are never dereferenced later.
The array of regulator_dev can be safely removed from state container.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NThiago Farina <tfarina@chromium.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

When platform_data is used for regulator (of_node of sec-core MFD device
is NULL) the config.of_node for regulator is not initialized. This NULL
value of config.of_node is later stored during regulator_register().
Thus any call by regulator consumers to of_get_regulator() will fail on
of_parse_phandle() returning NULL.

In this case (using platform_data and parent's driver of_node is NULL)
set the config.of_node to reg_node from platform_data.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

BUCK 3 and 4 share the same ramp delay. Hence make it a fall through
case instead of duplicating the code.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Fix building of s2mps11 regulator and clock drivers after renaming
regmap field in struct sec_pmic_dev in commit:
 - "mfd/rtc: s5m: Fix register updating by adding regmap for RTC"
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Commit e398b51a ("regulator: s2mps11: Convert to devm_regulator_register()")
intended to do this conversion. However the actual conversion to devm_* got
missed out. Fix this.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NSangbeom Kim <sbkim73@samsung.com>

Current code has wrong mask and val arguments for updating ramp_delay. Fix it.
Also ensure the return value of get_ramp_delay() won't greater than 3 because
the mask field for ramp_val only takes 2 bits.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current code calls regmap_update_bits() with mask and val arguments swapped.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Since now we have ramp_delay and ramp_disable as standard regulator
constraints and DT part using it so this patch removes legacy part i.e. getting
ramp_delayxx and ramp_enable from pdata since it can be passed as
standard regulator constraints.
Signed-off-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch adds DT support for parsing regulators constraints for parent(mfd)
node and moves some common intialising code out of loop while registering.
Signed-off-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Implementing set_ramp_rate() and using standard constraints for getting
ramp_delay and ramp_disable, instead of getting it as s2mps11 specific data
through platform data, makes driver more compliant with framework and reduces
the complexity for adding DT support.
Signed-off-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Currently driver uses local struct s2mps11_info to store ramp rate for bucks
whic its getting through platform data, so instead of using regulator
constraints it should use s2mps11_info to calculate ramp delay.
Signed-off-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch makes driver to use uV/us as units of ramp_delay. It makes driver
in compliance with regulator framework and make ramp rate precise.

This patch also sets default ramp rate in regulator descriptor which can be
used in case if case ramp rate is not set in regulator constraints.
Signed-off-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

All the drivers that need delay for the regulator voltage output voltage to
stabilize after being enabled or after being set to a new value has been
converted to implement enable_time and set_voltage_time_sel callbacks.
Then regulator core will take care of the necessary delay.

This patch removes the unneeded include of linux/delay.h in regulator drivers.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Cc: Daniel Jeong <daniel.jeong@ti.com>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Chiwoong Byun <woong.byun@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

For BUCK10 the control registers are wrongly set as buck9 control register
This patch corrects the control registers for buck10
Signed-off-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

This patch fix the abnormal ramp delay setting.
The shift operation was wrong.
Signed-off-by: NSangbeom Kim <sbkim73@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The number of regulator is known at compile time, use array to save pointer to
rdev makes the code simpler.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NSangbeom Kim <sbkim73@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Currently s2mps11->iodev, s2mps11->dev and config.dev point to NULL.
This patch fixes the settings for config.dev.
Current code does not need the *dev and *iodev of struct s2mps11_info,
so remove them.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NSangbeom Kim <sbkim73@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NSangbeom Kim <sbkim73@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch add Samsung S2MPS11 regulator driver.
The S2MPS11 can support 10 Bucks and 38 LDOs and RTC.
Especially, S2MPS11 is designed for high performance
Samsung application processor.
Signed-off-by: NSangbeom Kim <sbkim73@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>