mmc_select_hs400() calls __mmc_switch() which checks the switch is
successful using CMD13 (SEND_STATUS).  The problem is that it does that
using the timing settings of the previous mode.  That is prone to error,
especially when switching from HS to HS400 because the timing parameters
for HS mode are tighter than the timing parameters for HS400 mode.

In the case when CMD13 polling is used (i.e. not MMC_CAP_WAIT_WHILE_BUSY)
with the switch command, it must be assumed that using different modes on
the card and host must work.

However in the case when CMD13 polling is not used
(i.e. MMC_CAP_WAIT_WHILE_BUSY) mmc_select_hs400() can be made more
reliable by setting the host to the correct timing before sending CMD13.

This patch does that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Move the mmc_switch_status() function in preparation for calling it
in mmc_select_hs400().
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_select_hs400() begins with the card and host in HS200 mode.
Therefore, any commands sent to the card should use HS200 timing.
It is incorrect to set the host to High Speed (HS) timing before
sending the switch command.  Doing so is unreliable because
the timing parameters for HS mode are tighter than the timing
parameters for HS200 mode.  Thus the HS timings should be set
only after the card has switched mode.

However, it is not unreasonable first to reduce the frequency to
the HS mode frequency, which should make the switch command and
subsequent CMD13 commands more reliable.

This patch does that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Currently mmc_select_hs200() uses __mmc_switch() which checks the
success of the switch to HS200 mode using CMD13 (SEND_STATUS).
The problem is that it does that using the timing settings of legacy
mode.  That is prone to error, not least because the timing parameters
for legacy mode are tighter than the timing parameters for HS200 mode.

In the case when CMD13 polling is used (i.e. not MMC_CAP_WAIT_WHILE_BUSY)
with the switch command, it must be assumed that using different modes on
the card and host must work.

However in the case when CMD13 polling is not used
(i.e. MMC_CAP_WAIT_WHILE_BUSY) mmc_select_hs200() can be made more
reliable by setting the host to the correct timing before sending CMD13.

This patch does that.

A complication is that the caller, mmc_select_timing(), will ignore a
switch error (indicated by -EBADMSG), assume the old mode is valid
and continue, so the old timing must be restored in that case.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The commit converting pxamci to slot-gpio API inverted the logic of the
read-only gpio. Fix it by inverting the logic again.

Fixes: fd546ee6 ("mmc: pxamci: fix card detect with slot-gpio API")
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

__GFP_WAIT was renamed for __GFP_RECLAIM and the gfpflags_allow_blocking()
helper was added.

Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge second patch-bomb from Andrew Morton:

 - most of the rest of MM

 - procfs

 - lib/ updates

 - printk updates

 - bitops infrastructure tweaks

 - checkpatch updates

 - nilfs2 update

 - signals

 - various other misc bits: coredump, seqfile, kexec, pidns, zlib, ipc,
   dma-debug, dma-mapping, ...

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (102 commits)
  ipc,msg: drop dst nil validation in copy_msg
  include/linux/zutil.h: fix usage example of zlib_adler32()
  panic: release stale console lock to always get the logbuf printed out
  dma-debug: check nents in dma_sync_sg*
  dma-mapping: tidy up dma_parms default handling
  pidns: fix set/getpriority and ioprio_set/get in PRIO_USER mode
  kexec: use file name as the output message prefix
  fs, seqfile: always allow oom killer
  seq_file: reuse string_escape_str()
  fs/seq_file: use seq_* helpers in seq_hex_dump()
  coredump: change zap_threads() and zap_process() to use for_each_thread()
  coredump: ensure all coredumping tasks have SIGNAL_GROUP_COREDUMP
  signal: remove jffs2_garbage_collect_thread()->allow_signal(SIGCONT)
  signal: introduce kernel_signal_stop() to fix jffs2_garbage_collect_thread()
  signal: turn dequeue_signal_lock() into kernel_dequeue_signal()
  signals: kill block_all_signals() and unblock_all_signals()
  nilfs2: fix gcc uninitialized-variable warnings in powerpc build
  nilfs2: fix gcc unused-but-set-variable warnings
  MAINTAINERS: nilfs2: add header file for tracing
  nilfs2: add tracepoints for analyzing reading and writing metadata files
  ...

Pull rdma updates from Doug Ledford:
 "This is my initial round of 4.4 merge window patches.  There are a few
  other things I wish to get in for 4.4 that aren't in this pull, as
  this represents what has gone through merge/build/run testing and not
  what is the last few items for which testing is not yet complete.

   - "Checksum offload support in user space" enablement
   - Misc cxgb4 fixes, add T6 support
   - Misc usnic fixes
   - 32 bit build warning fixes
   - Misc ocrdma fixes
   - Multicast loopback prevention extension
   - Extend the GID cache to store and return attributes of GIDs
   - Misc iSER updates
   - iSER clustering update
   - Network NameSpace support for rdma CM
   - Work Request cleanup series
   - New Memory Registration API"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (76 commits)
  IB/core, cma: Make __attribute_const__ declarations sparse-friendly
  IB/core: Remove old fast registration API
  IB/ipath: Remove fast registration from the code
  IB/hfi1: Remove fast registration from the code
  RDMA/nes: Remove old FRWR API
  IB/qib: Remove old FRWR API
  iw_cxgb4: Remove old FRWR API
  RDMA/cxgb3: Remove old FRWR API
  RDMA/ocrdma: Remove old FRWR API
  IB/mlx4: Remove old FRWR API support
  IB/mlx5: Remove old FRWR API support
  IB/srp: Dont allocate a page vector when using fast_reg
  IB/srp: Remove srp_finish_mapping
  IB/srp: Convert to new registration API
  IB/srp: Split srp_map_sg
  RDS/IW: Convert to new memory registration API
  svcrdma: Port to new memory registration API
  xprtrdma: Port to new memory registration API
  iser-target: Port to new memory registration API
  IB/iser: Port to new fast registration API
  ...

Pull trivial updates from Jiri Kosina:
 "Trivial stuff from trivial tree that can be trivially summed up as:

   - treewide drop of spurious unlikely() before IS_ERR() from Viresh
     Kumar

   - cosmetic fixes (that don't really affect basic functionality of the
     driver) for pktcdvd and bcache, from Julia Lawall and Petr Mladek

   - various comment / printk fixes and updates all over the place"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
  bcache: Really show state of work pending bit
  hwmon: applesmc: fix comment typos
  Kconfig: remove comment about scsi_wait_scan module
  class_find_device: fix reference to argument "match"
  debugfs: document that debugfs_remove*() accepts NULL and error values
  net: Drop unlikely before IS_ERR(_OR_NULL)
  mm: Drop unlikely before IS_ERR(_OR_NULL)
  fs: Drop unlikely before IS_ERR(_OR_NULL)
  drivers: net: Drop unlikely before IS_ERR(_OR_NULL)
  drivers: misc: Drop unlikely before IS_ERR(_OR_NULL)
  UBI: Update comments to reflect UBI_METAONLY flag
  pktcdvd: drop null test before destroy functions

Pull HID updates from Jiri Kosina:
 "Highlights:

   - Intel Skylake Win8 precision touchpads support fixes/improvements
     from Mika Westerberg

   - Lenovo Yoga 2 quirk from Ritesh Raj Sarraf

   - potential uninitialized buffer access fix in HID core from Richard
     Purdie

   - Wacom Intuos and Wacom Cintiq 2 support improvements from Jason
     Gerecke and Ping Cheng

   - initiation of sysfs deprecation process for most of the roccat
     drivers, from the roccat support maintiner Stefan Achatz

   - quite a few device ID / quirk additions and small fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (30 commits)
  HID: logitech: Add support for G29
  HID: logitech: Simplify wheel detection scheme
  HID: wacom: Call 'wacom_query_tablet_data' only after 'hid_hw_start'
  HID: wacom: Fix ABS_MISC reporting for Cintiq Companion 2
  HID: wacom: Remove useless conditions from 'wacom_query_tablet_data'
  HID: wacom: fix Intuos wireless report id issue
  HID: fix some indenting issues
  HID: wacom: Expect 'touch_max' touches if HID_DG_CONTACTCOUNT not present
  HID: wacom: Tie cached HID_DG_CONTACTCOUNT indices to report ID
  HID: roccat: Fixed resubmit: Deprecating most Roccat sysfs attributes
  HID: wacom: Report full pressure range for Intuos, Cintiq 13HD Touch
  HID: wacom: Add support for Cintiq Companion 2
  HID: multitouch: Fetch feature reports on demand for Win8 devices
  HID: sensor-hub: Add quirk for Lenovo Yoga 2 with ITE Chips
  HID: usbhid: Fix for the WiiU adapter from Mayflash
  HID: corsair: boolify struct k90_led.removed
  HID: corsair: Add Corsair Vengeance K90 driver
  HID: hid-input: allow input_configured callback return errors
  HID: multitouch: Add suffix for HID_DG_TOUCHPAD
  HID: i2c-hid: Fill in physical device providing HID functionality
  ...

Pull livepatching fix from Jiri Kosina:
 "A fix for a kernel oops in case CONFIG_DEBUG_SET_MODULE_RONX is unset
  (as in such case it's possible for module struct to share a page with
  executable text, which is currently not being handled with grace) from
  Josh Poimboeuf"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
  livepatch: Fix crash with !CONFIG_DEBUG_SET_MODULE_RONX

d0edd852 ("ipc: convert invalid scenarios to use WARN_ON") relaxed the
nil dst parameter check, originally being a full BUG_ON.  However, this
check seems quite unnecessary when the only purpose is for
ceckpoint/restore (MSG_COPY flag):

o The copy variable is set initially to nil, apparently as a way of
  ensuring that prepare_copy is previously called.  Which is in fact done,
  unconditionally at the beginning of do_msgrcv.

o There is no concurrency with 'copy' (stack allocated in do_msgrcv).

Furthermore, any errors in 'copy' (and thus prepare_copy/copy_msg) should
always handled by IS_ERR() family.  Therefore remove this check altogether
as it can never occur with the current users.
Signed-off-by: NDavidlohr Bueso <dbueso@suse.de>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

alder32 was renamed to zlib_adler32 since before 2.6.11.
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In some cases we may end up killing the CPU holding the console lock
while still having valuable data in logbuf. E.g. I'm observing the
following:

- A crash is happening on one CPU and console_unlock() is being called on
  some other.

- console_unlock() tries to print out the buffer before releasing the lock
  and on slow console it takes time.

- in the meanwhile crashing CPU does lots of printk()-s with valuable data
  (which go to the logbuf) and sends IPIs to all other CPUs.

- console_unlock() finishes printing previous chunk and enables interrupts
  before trying to print out the rest, the CPU catches the IPI and never
  releases console lock.

This is not the only possible case: in VT/fb subsystems we have many other
console_lock()/console_unlock() users.  Non-masked interrupts (or
receiving NMI in case of extreme slowness) will have the same result.
Getting the whole console buffer printed out on crash should be top
priority.

[akpm@linux-foundation.org: tweak comment text]
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Baoquan He <bhe@redhat.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Xie XiuQi <xiexiuqi@huawei.com>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Like dma_unmap_sg, dma_sync_sg* should be called with the original number
of entries passed to dma_map_sg, so do the same check in the sync path as
we do in the unmap path.
Signed-off-by: NRobin Murphy <robin.murphy@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Many DMA controllers and other devices set max_segment_size to
indicate their scatter-gather capability, but have no interest in
segment_boundary_mask. However, the existence of a dma_parms structure
precludes the use of any default value, leaving them as zeros (assuming
a properly kzalloc'ed structure). If a well-behaved IOMMU (or SWIOTLB)
then tries to respect this by ensuring a mapped segment does not cross
a zero-byte boundary, hilarity ensues.

Since zero is a nonsensical value for either parameter, treat it as an
indicator for "default", as might be expected. In the process, clean up
a bit by replacing the bare constants with slightly more meaningful
macros and removing the superfluous "else" statements.

[akpm@linux-foundation.org: dma-mapping.h needs sizes.h for SZ_64K]
Signed-off-by: NRobin Murphy <robin.murphy@arm.com>
Reviewed-by: NSumit Semwal <sumit.semwal@linaro.org>
Acked-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

setpriority(PRIO_USER, 0, x) will change the priority of tasks outside of
the current pid namespace.  This is in contrast to both the other modes of
setpriority and the example of kill(-1).  Fix this.  getpriority and
ioprio have the same failure mode, fix them too.

Eric said:

: After some more thinking about it this patch sounds justifiable.
:
: My goal with namespaces is not to build perfect isolation mechanisms
: as that can get into ill defined territory, but to build well defined
: mechanisms.  And to handle the corner cases so you can use only
: a single namespace with well defined results.
:
: In this case you have found the two interfaces I am aware of that
: identify processes by uid instead of by pid.  Which quite frankly is
: weird.  Unfortunately the weird unexpected cases are hard to handle
: in the usual way.
:
: I was hoping for a little more information.  Changes like this one we
: have to be careful of because someone might be depending on the current
: behavior.  I don't think they are and I do think this make sense as part
: of the pid namespace.
Signed-off-by: NBen Segall <bsegall@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ambrose Feinstein <ambrose@google.com>
Acked-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kexec output message misses the prefix "kexec", when Dave Young split the
kexec code.  Now, we use file name as the output message prefix.

Currently, the format of output message:
[  140.290795] SYSC_kexec_load: hello, world
[  140.291534] kexec: sanity_check_segment_list: hello, world

Ideally, the format of output message:
[   30.791503] kexec: SYSC_kexec_load, Hello, world
[   79.182752] kexec_core: sanity_check_segment_list, Hello, world

Remove the custom prefix "kexec" in output message.
Signed-off-by: NMinfei Huang <mnfhuang@gmail.com>
Acked-by: NDave Young <dyoung@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since 5cec38ac ("fs, seq_file: fallback to vmalloc instead of oom kill
processes") seq_buf_alloc() avoids calling the oom killer for PAGE_SIZE or
smaller allocations; but larger allocations can use the oom killer via
vmalloc().  Thus reads of small files can return ENOMEM, but larger files
use the oom killer to avoid ENOMEM.

The effect of this bug is that reads from /proc and other virtual
filesystems can return ENOMEM instead of the preferred behavior - oom
killing something (possibly the calling process).  I don't know of anyone
except Google who has noticed the issue.

I suspect the fix is more needed in smaller systems where there isn't any
reclaimable memory.  But these seem like the kinds of systems which
probably don't use the oom killer for production situations.

Memory overcommit requires use of the oom killer to select a victim
regardless of file size.

Enable oom killer for small seq_buf_alloc() allocations.

Fixes: 5cec38ac ("fs, seq_file: fallback to vmalloc instead of oom kill processes")
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NGreg Thelen <gthelen@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

strint_escape_str() escapes input string by given criteria.  In case of
seq_escape() the criteria is to convert some characters to their octal
representation.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This improves code readability.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change zap_threads() paths to use for_each_thread() rather than
while_each_thread().

While at it, change zap_threads() to avoid the nested if's to make the
code more readable and lessen the indentation.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Kyle Walker <kwalker@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Stanislav Kozina <skozina@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

task_will_free_mem() is wrong in many ways, and in particular the
SIGNAL_GROUP_COREDUMP check is not reliable: a task can participate in the
coredumping without SIGNAL_GROUP_COREDUMP bit set.

change zap_threads() paths to always set SIGNAL_GROUP_COREDUMP even if
other CLONE_VM processes can't react to SIGKILL.  Fortunately, at least
oom-kill case if fine; it kills all tasks sharing the same mm, so it
should also kill the process which actually dumps the core.

The change in prepare_signal() is not strictly necessary, it just ensures
that the patch does not bring another subtle behavioural change.  But it
reminds us that this SIGNAL_GROUP_EXIT/COREDUMP case needs more changes.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Kyle Walker <kwalker@redhat.com>
Acked-by: NMichal Hocko <mhocko@suse.com>
Cc: Stanislav Kozina <skozina@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

jffs2_garbage_collect_thread() does allow_signal(SIGCONT) for no reason,
SIGCONT will wake a stopped task up even if it is ignored.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Reviewed-by: NTejun Heo <tj@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

jffs2_garbage_collect_thread() can race with SIGCONT and sleep in
TASK_STOPPED state after it was already sent. Add the new helper,
kernel_signal_stop(), which does this correctly.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Reviewed-by: NTejun Heo <tj@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

1. Rename dequeue_signal_lock() to kernel_dequeue_signal(). This
   matches another "for kthreads only" kernel_sigaction() helper.

2. Remove the "tsk" and "mask" arguments, they are always current
   and current->blocked. And it is simply wrong if tsk != current.

3. We could also remove the 3rd "siginfo_t *info" arg but it looks
   potentially useful. However we can simplify the callers if we
   change kernel_dequeue_signal() to accept info => NULL.

4. Remove _irqsave, it is never called from atomic context.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Reviewed-by: NTejun Heo <tj@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It is hardly possible to enumerate all problems with block_all_signals()
and unblock_all_signals().  Just for example,

1. block_all_signals(SIGSTOP/etc) simply can't help if the caller is
   multithreaded. Another thread can dequeue the signal and force the
   group stop.

2. Even is the caller is single-threaded, it will "stop" anyway. It
   will not sleep, but it will spin in kernel space until SIGCONT or
   SIGKILL.

And a lot more. In short, this interface doesn't work at all, at least
the last 10+ years.

Daniel said:

  Yeah the only times I played around with the DRM_LOCK stuff was when
  old drivers accidentally deadlocked - my impression is that the entire
  DRM_LOCK thing was never really tested properly ;-) Hence I'm all for
  purging where this leaks out of the drm subsystem.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NDave Airlie <airlied@redhat.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some false positive warnings are reported for powerpc build.

The following warnings are reported in
 http://kisskb.ellerman.id.au/kisskb/buildresult/12519703/

   CC      fs/nilfs2/super.o
 fs/nilfs2/super.c: In function 'nilfs_resize_fs':
 fs/nilfs2/super.c:376:2: warning: 'blocknr' may be used uninitialized in this function [-Wuninitialized]
 fs/nilfs2/super.c:362:11: note: 'blocknr' was declared here
   CC      fs/nilfs2/recovery.o
 fs/nilfs2/recovery.c: In function 'nilfs_salvage_orphan_logs':
 fs/nilfs2/recovery.c:631:21: warning: 'sum' may be used uninitialized in this function [-Wuninitialized]
 fs/nilfs2/recovery.c:585:32: note: 'sum' was declared here
 fs/nilfs2/recovery.c: In function 'nilfs_search_super_root':
 fs/nilfs2/recovery.c:873:11: warning: 'sum' may be used uninitialized in this function [-Wuninitialized]

Another similar warning is reported in
 http://kisskb.ellerman.id.au/kisskb/buildresult/12520079/

   CC      fs/nilfs2/btree.o
 fs/nilfs2/btree.c: In function 'nilfs_btree_convert_and_insert':
 include/asm-generic/bitops/non-atomic.h:105:20: warning: 'bh' may be used uninitialized in this function [-Wuninitialized]
 fs/nilfs2/btree.c:1859:22: note: 'bh' was declared here

This cleans out these warnings by forcing the variables to be initialized.
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the following build warnings:

 $ make W=1
 [...]
   CC [M]  fs/nilfs2/btree.o
 fs/nilfs2/btree.c: In function 'nilfs_btree_split':
 fs/nilfs2/btree.c:923:8: warning: variable 'newptr' set but not used [-Wunused-but-set-variable]
   __u64 newptr;
         ^
 fs/nilfs2/btree.c:922:8: warning: variable 'newkey' set but not used [-Wunused-but-set-variable]
   __u64 newkey;
         ^
   CC [M]  fs/nilfs2/dat.o
 fs/nilfs2/dat.c: In function 'nilfs_dat_prepare_end':
 fs/nilfs2/dat.c:158:8: warning: variable 'start' set but not used [-Wunused-but-set-variable]
   __u64 start;
         ^
   CC [M]  fs/nilfs2/segment.o
 fs/nilfs2/segment.c: In function 'nilfs_segctor_do_immediate_flush':
 fs/nilfs2/segment.c:2433:6: warning: variable 'err' set but not used [-Wunused-but-set-variable]
   int err;
       ^
   CC [M]  fs/nilfs2/sufile.o
 fs/nilfs2/sufile.c: In function 'nilfs_sufile_alloc':
 fs/nilfs2/sufile.c:320:27: warning: variable 'ncleansegs' set but not used [-Wunused-but-set-variable]
   unsigned long nsegments, ncleansegs, nsus, cnt;
                            ^
   CC [M]  fs/nilfs2/alloc.o
 fs/nilfs2/alloc.c: In function 'nilfs_palloc_prepare_alloc_entry':
 fs/nilfs2/alloc.c:478:38: warning: variable 'groups_per_desc_block' set but not used [-Wunused-but-set-variable]
   unsigned long n, entries_per_group, groups_per_desc_block;
                                       ^
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds header file "include/trace/events/nilfs2.h" to maintainer-ship
of nilfs2 so that updates to the nilfs2 header file go to the mailing list
of nilfs2.
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Hitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds tracepoints for analyzing requests of reading and writing
metadata files.  The tracepoints cover every in-place mdt files (cpfile,
sufile, and datfile).

Example of tracing mdt_insert_new_block():
              cp-14635 [000] ...1 30598.199309: nilfs2_mdt_insert_new_block: inode = ffff88022a8d0178 ino = 3 block = 155
              cp-14635 [000] ...1 30598.199520: nilfs2_mdt_insert_new_block: inode = ffff88022a8d0178 ino = 3 block = 5
              cp-14635 [000] ...1 30598.200828: nilfs2_mdt_insert_new_block: inode = ffff88022a8d0178 ino = 3 block = 253
Signed-off-by: NHitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: TK Kato <TK.Kato@wdc.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds tracepoints which would be useful for analyzing segment
usage from a perspective of high level sufile manipulation (check, alloc,
free).  sufile is an important in-place updated metadata file, so
analyzing the behavior would be useful for performance turning.

example of usage (a case of allocation):

$ sudo bin/tpoint nilfs2:nilfs2_segment_usage_allocated
Tracing nilfs2:nilfs2_segment_usage_allocated. Ctrl-C to end.
        segctord-17800 [002] ...1 10671.867294: nilfs2_segment_usage_allocated: sufile = ffff880054f908a8 segnum = 2
        segctord-17800 [002] ...1 10675.073477: nilfs2_segment_usage_allocated: sufile = ffff880054f908a8 segnum = 3
Signed-off-by: NHitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Benixon Dhas <benixon.dhas@wdc.com>
Cc: TK Kato <TK.Kato@wdc.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds a tracepoint for transaction events of nilfs.  With the
tracepoint, these events can be tracked: begin, abort, commit, trylock,
lock, and unlock.  Basically, these events have corresponding functions
e.g.  begin event corresponds nilfs_transaction_begin().  The unlock event
is an exception.  It corresponds to the iteration in
nilfs_transaction_lock().

Only one tracepoint is introcued: nilfs2_transaction_transition.  The
above events are distinguished with newly introduced enum.  With this
tracepoint, we can analyse a critical section of segment constructoin.

Sample output by tpoint of perf-tools:
              cp-4457  [000] ...1    63.266220: nilfs2_transaction_transition: sb = ffff8802112b8800 ti = ffff8800bf5ccc58 count = 1 flags = 9 state = BEGIN
              cp-4457  [000] ...1    63.266221: nilfs2_transaction_transition: sb = ffff8802112b8800 ti = ffff8800bf5ccc58 count = 0 flags = 9 state = COMMIT
              cp-4457  [000] ...1    63.266221: nilfs2_transaction_transition: sb = ffff8802112b8800 ti = ffff8800bf5ccc58 count = 0 flags = 9 state = COMMIT
        segctord-4371  [001] ...1    68.261196: nilfs2_transaction_transition: sb = ffff8802112b8800 ti = ffff8800b889bdf8 count = 0 flags = 10 state = TRYLOCK
        segctord-4371  [001] ...1    68.261280: nilfs2_transaction_transition: sb = ffff8802112b8800 ti = ffff8800b889bdf8 count = 0 flags = 10 state = LOCK
        segctord-4371  [001] ...1    68.261877: nilfs2_transaction_transition: sb = ffff8802112b8800 ti = ffff8800b889bdf8 count = 1 flags = 10 state = BEGIN
        segctord-4371  [001] ...1    68.262116: nilfs2_transaction_transition: sb = ffff8802112b8800 ti = ffff8800b889bdf8 count = 0 flags = 18 state = COMMIT
        segctord-4371  [001] ...1    68.265032: nilfs2_transaction_transition: sb = ffff8802112b8800 ti = ffff8800b889bdf8 count = 0 flags = 18 state = UNLOCK
        segctord-4371  [001] ...1   132.376847: nilfs2_transaction_transition: sb = ffff8802112b8800 ti = ffff8800b889bdf8 count = 0 flags = 10 state = TRYLOCK

This patch also does trivial cleaning of comma usage in collection stage
transition event for consistent coding style.
Signed-off-by: NHitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds a tracepoint for tracking stage transition of block
collection in segment construction.  With the tracepoint, we can analysis
the behavior of segment construction in depth.  It would be useful for
bottleneck detection and debugging, etc.

The tracepoint is created with the standard trace API of linux (like ext3,
ext4, f2fs and btrfs).  So we can analysis with existing tools easily.  Of
course, more detailed analysis will be possible if we can create nilfs
specific analysis tools.

Below is an example of event dump with Brendan Gregg's perf-tools
(https://github.com/brendangregg/perf-tools).  Time consumption between
each stage can be obtained.

$ sudo bin/tpoint nilfs2:nilfs2_collection_stage_transition
Tracing nilfs2:nilfs2_collection_stage_transition. Ctrl-C to end.
        segctord-14875 [003] ...1 28311.067794: nilfs2_collection_stage_transition: sci = ffff8800ce6de000 stage = ST_INIT
        segctord-14875 [003] ...1 28311.068139: nilfs2_collection_stage_transition: sci = ffff8800ce6de000 stage = ST_GC
        segctord-14875 [003] ...1 28311.068139: nilfs2_collection_stage_transition: sci = ffff8800ce6de000 stage = ST_FILE
        segctord-14875 [003] ...1 28311.068486: nilfs2_collection_stage_transition: sci = ffff8800ce6de000 stage = ST_IFILE
        segctord-14875 [003] ...1 28311.068540: nilfs2_collection_stage_transition: sci = ffff8800ce6de000 stage = ST_CPFILE
        segctord-14875 [003] ...1 28311.068561: nilfs2_collection_stage_transition: sci = ffff8800ce6de000 stage = ST_SUFILE
        segctord-14875 [003] ...1 28311.068565: nilfs2_collection_stage_transition: sci = ffff8800ce6de000 stage = ST_DAT
        segctord-14875 [003] ...1 28311.068573: nilfs2_collection_stage_transition: sci = ffff8800ce6de000 stage = ST_SR
        segctord-14875 [003] ...1 28311.068574: nilfs2_collection_stage_transition: sci = ffff8800ce6de000 stage = ST_DONE

For capturing transition correctly, this patch adds wrappers for the
member scnt of nilfs_cstage.  With this change, every transition of the
stage can produce trace event in a correct manner.
Signed-off-by: NHitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As a nilfs2 volume ages, the amount of available disk space decreases
little by little due to bloat of DAT (disk address translation) metadata
file.  Even if we delete all files in a file system and free their block
addresses from the DAT file through a garbage collection, empty DAT blocks
are not freed.

This fixes the issue by extending the deallocator of block addresses so
that empty data blocks and empty bitmap blocks of DAT are deleted.

The following comparison shows the effect of this patch.  Each shows disk
amount information of a nilfs2 volume that we cleaned out by deleting all
files and running gc after having filled 90% of its capacity.

Before:
Filesystem     1K-blocks     Used Available Use% Mounted on
/dev/sda1      500105212  3022844 472072192   1% /test

After:
Filesystem     1K-blocks     Used Available Use% Mounted on
/dev/sda1      500105212    16380 475078656   1% /test
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds delete functions for data blocks of metadata files using bitmap
based allocator.  nilfs_palloc_delete_entry_block() deletes an entry block
(e.g.  block storing dat entries), and nilfs_palloc_delete_bitmap_block()
deletes a bitmap block, respectively.

These helpers are intended to be used in the successive change on
deallocator of block addresses ("nilfs2: free unused dat file blocks
during garbage collection").
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This unfolds nilfs_palloc_group_is_in() helper function into
nilfs_palloc_freev() function to simplify a range check and an index
calculation repeatedy performed in a loop of the function.
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The current implementation of nilfs_palloc_find_available_slot() function
is overkill.  The underlying bit search routine is well optimized, so this
uses it more simply in nilfs_palloc_find_available_slot().
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In the bitmap based allocator implementation, nilfs_mdt_bgl_lock() helper
is frequently used to get a spinlock protecting a target block group.
This reduces its usage and simplifies arguments of some related functions
by directly passing a pointer to the spinlock.
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This uses nilfs_warning() to replace "printk(KERN_WARNING ...);" in the
bitmap based allocator implementation of nilfs2.  The warning messages are
modified to include the device name and the inode number in each message.
This makes it clear which metadata file of which device has output
warnings such as "entry number xxxx already freed".
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>