For any SCSI command, if the driver receives IOC status =
SCSI_IOC_TERMINATED and log info = 0x32010081 then that command will be
completed with DID_RESET host status.

The definition of this log info value is "Virtual IO has failed and has
to be retried".

Firmware will provide this log info value with IOC Status
"SCSI_IOC_TERMINATED", whenever a drive (with is a part of a volume)
is pulled and pushed back within some minimal delay.  With this log info
value, firmware informs the driver to retry the failed IO command
infinite times, so to provide some time for the firmware to discover
the reinserted drive successfully instated of just retrying failed
command for five times( doesn't giving enough time for firmware to
complete the drive discovery) and failing the IO permanently even
though drive came back successfully.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Change Set:

1. Extended the upper boundary restriction for the module parameter
   max_sgl_entries. Earlier, the max_sgl_entries was capped at the
   SCSI_MAX_SG_SEGMENTS kernel definition. With this change, the user
   would be able to set the max_sgl_entries to any value which is
   greater than SCSI_MAX_SG_SEGMENTS and less than the minimum of
   SCSI_MAX_SG_CHAIN_SEGMENTS & hardware limit (Calculated using
   IOCFacts's MaxChainDepth).

2. Added a print for the message log whenever the user sets the
   max_sgl_entries to a value greater than SCSI_MAX_SG_SEGMENTS to
   warn about the kernel definition overriding.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Change List in this MPI2 specification,

1. Added SSUTimeout field to MPI2_CONFIG_PAGE_BIOS_1,
   and more defines for the BiosOptions field.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Bump driver version to 19.100.00.00.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

mpt2sas, mpt3sas: Fail the host reset initiated due to discovery related I/O timeouts at driver load time

When a flaky disk is there in a topology then during driver load,
discovery related I/O times out; which results in SCSI error recovery
initiating host reset and then the controller won't see any disk.

In this patch, The driver would return FAILED status to the host reset
initiated due to discovery related I/O timeout if ioc->is_driver_loading
is set. This flag would be set until we exit out of scsih_scan_finished().
i.e.
During device discovery if one of the disk is flaky
(which responds to some discovery commands and doesn't respond to some)
the driver wouldn't perform host reset for discovery related I/O timeout.
Instead it would return Failure for the host reset resulting in the
flaky disk getting removed by the SCSI Mid layer,
so other disks would be added correctly.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This patch will log a message when driver receives "Temperature Threshold
exceeded" event from any temperature sensor.

The message will look similar to like:
mpt3sas0: Temperature Threshold flags a b c d exceeded for Sensor: x !!!
mpt3sas0: Current Temp In Celsius: y

where a b c d are threshold flags 0 1 2 3

Change_set:
1. Get the number of sensor count of this IOC by reading IO Unit page 8 at
   driver initialization time.
2. Also unmask the Temperature Threshold Event at driver initialization
   time
3. Whenever a MPI2_EVENT_TEMP_THRESHOLD event is received from the
   firmware, then print the sensor number, the maximum threshold number it
   has exceed and the current temperature of this sensor.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Below is the changeset from the MPI specification and 2.00.34 header
files:

1) Defined additional bits in the BiosOptions field of BIOS Page 1 to
   allow for finer control of X86 BIOS and UEFI BSD.
2) For the Clean Tool, reserved bit 26 of the Flags field for product
   specific use.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Update megaraid_sas driver version.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

struct fusion_context *fusion is already memset to '0', so remove a
redundant call to memmset "fusion->load_balance_info" to '0'.
Signed-off-by: NChaitra Basappa <chaitra.basappa@avagotech.com>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

1) For fusion adapters, limit reserved frames for non SCSI commands to 8
   (3 for parallel IOCTLs + 5 for driver's internal DCMDs).
   Earlier reserved commands for non SCSI IO frames was set to 32, so with
   this implementation, increased per controller "can_queue".
   Behavior of MFI controllers will remain unchanged.

2) Optimize the code related to per controller's 'can_queue' setting.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NChaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Driver calls megasas_complete_cmd() to call wake_up() for each MFI frame
that was issued through the ioctl() interface prior to the kill adapter.
This ensures userspace ioctl() system calls issued just before a kill
adapter don't get stuck in wait state and IOCTLs are returned to
the application.

Cc: <stable@vger.kernel.org>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NChaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Update driver "mask_interrupts" before enable/disable hardware interrupt
in order to avoid missing interrupts because of "mask_interrupts" still
set to 1 and hardware interrupts are enabled.

Cc: <stable@vger.kernel.org>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NChaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This patch will address the issue of SCSI device created at OS level for
non existing VD. ldTgtIdtoLd[] array has size 256 for Extended VD firmware
and 128 for legacy firmware. Accessing indices beyond array size (OS will
send TUR, INQUIRY.. commands upto device index 255), may return valid LD
value and that particular SCSI command will be SUCCESS and creating SCSI
device for non existing target(VD).

For legacy firmware (64 VD firmware), invalidates LD (by setting LD value
to 0xff) in LdTgtIdtoLd[] array for device index beyond 127, so that
invalid LD(0xff) value should be returned beyond device index beyond 127.

Cc: <stable@vger.kernel.org>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This patch adds support for Secure Encrypting Drives (SED) in JBOD mode:

1) If the firmware supports SED JBOD, all non read/write commands to JBODs
   will be sent via firmware path, and read/write commands to JBODs will
   be sent via fastpath.
2) If the firmware does not support SED JBOD, driver will fall back to the
   old design, i.e. send all JBOD I/O via fastpath.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NChaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This patch addresses below issues:

1) Few endianness bug fixes.
2) Break the iteration after (MAX_LOGICAL_DRIVES_EXT - 1)),
   instead of MAX_LOGICAL_DRIVES_EXT.
3) Optimization in MFI INIT frame before firing.
4) MFI IO frame should be 256bytes aligned.  Code is optimized to reduce
   the size of frame for fusion adapters and make the MFI frame size
   calculation a bit transparent and readable.

Cc: <stable@vger.kernel.org>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NChaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

It is not good practice to display the kernel pointer in any message logs,
and it doesn't display any additional information. And as we know have
block-layer assigned tags we can use them to differentiate the messages.
So remove any pointer references from the displayed messages.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

scsi_log_send() would display buffer pointer for higher logging levels.
This is not only of questionable value but also exposes kernel pointer to
userspace, which is discouraged in some setups. So drop this message
altogether.
Tested-by: NRobert Elliott <elliott@hp.com>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Instead of having constants.c littered with ifdef statements we should
be moving dummy functions into the header and condintionally compile in
constants.c if selected. And update the Kconfig description to reflect
the actual size difference.
Suggested-by: NChristoph Hellwig <hch@infradead.org>
Tested-by: NRobert Elliott <elliott@hp.com>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Convert scsi_print_result() to use the per-cpu buffer for decoding the
command result and disposition.
Tested-by: NRobert Elliott <elliott@hp.com>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Convert sense buffer logging to use the per-cpu buffer to avoid line
breakup.
Tested-by: NRobert Elliott <elliott@hp.com>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

libata already uses an internal buffer, so we should be using
__scsi_format_command() here.
Tested-by: NRobert Elliott <elliott@hp.com>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Use an external buffer for __scsi_print_command() and move command
logging over to use the per-cpu logging buffer.  With that we can
guarantee the command always will always be formatted in one line.
So we can even print out a variable length command correctly across
several lines. Finally rename __scsi_print_command() to
__scsi_format_comment() to better reflect the functionality.
Tested-by: NRobert Elliott <elliott@hp.com>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The request tag provides a concise identification of a SCSI
command, so we should be printing that out for scmd_printk().
Suggested-by: NChristoph Hellwig <hch@lst.de>
Tested-by: NRobert Elliott <elliott@hp.com>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Implement a per-cpu buffer for formatting messages to avoid line breaks
up under high load.  This patch implements scmd_printk() and
sdev_prefix_printk() using the per-cpu buffer and makes sdev_printk() a
wrapper for sdev_prefix_printk().
Tested-by: NRobert Elliott <elliott@hp.com>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

On win8 and win8 r2 hosts force SPC-3 compliance for MSFT virtual disks.
Ubuntu has been carrying a similar patch outside the tree for a while now.
Starting with win10, the host will support SPC-3 compliance. Based on all
the testing that has been done on win8 and win8 r2 hosts, we are comfortable
claiming SPC-3 compliance on these hosts as well. This will enable TRIM
support on these hosts.

Suggested by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NLong Li <longli@microsoft.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Commit 4cd83ecd changed the limits to
reflect the values on the host. It turns out that WS2008R2 cannot
correctly handle these new limits. Fix this bug by setting the limits
based on the host.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NLong Li <longli@microsoft.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The host asks the guest to scan when a LUN is removed or added.
The only way a guest can identify the removed LUN is when an I/O is
attempted on a removed LUN - the SRB status code indicates that the LUN
is invalid. We currently handle this SRB status and remove the device.

Rather than waiting for an I/O to remove the device, force the discovery of
LUNs that may have been removed prior to discovering LUNs that may have
been added.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NLong Li <longli@microsoft.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The virtual HBA that storvsc implements can support multiple channels and
targets. So, scan the host when the host notifies that a scan is needed.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NLong Li <longli@microsoft.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

STORVSC uses its own momory pool to manage device request data.  However,
the SCSI layer already has a mechanisim for allocating additional memory
for each command issued to device driver. This patch removes the memory
pool in STORVSC and makes it use SCSI layer to allocate memory for device
request data.
Reviewed-by: NLong Li <longli@microsoft.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This patch, applicable to 8G/4G/2G adapters, adds a call that
resumes transmit operations after a link bounce. Without it, targets
that tried to suspend exchanges after a link bounce (such as tape devices
using sequence level error recovery) would never resume io operation,
causing scan failures, and eventually deadlocks if a device removal
request is made.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NDick Kennedy <dick.kennedy@emulex.com>
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

'num_tags' is an unsigned char, so the check for 'ESP_MAX_TAGS'
(which is set to 256) is pointless.
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The "issue_reset" can be used uninitialized.  It should be set to false
at the start.

Also I cleaned up the types a little by using bool.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The "issue_reset" variable can be used uninitialized.  It should be set
to false at the start.

Also I cleaned up the types by using bool.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
And use the sizeof on the to string rather than strlen on the from string.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Accept the WRITE BUFFER command and do nothing other than
set the appropriate "microcode has been changed" UA on the LU.

>From an earlier patch by Doug Gilbert.
Signed-off-by: NEwan D. Milne <emilne@redhat.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Tested-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Generate a REPORTED LUNS DATA HAS CHANGED Unit Attention if
sysfs "max_luns" is used to change the number of scsi_debug LUNs.
This is only done if scsi_debug_scsi_level is SPC-3 or above.
Additionally, implement SPC-4 behavior which only generates
this Unit Attention on the first LUN on the target to receive
a command after the change.  This condition is cleared when
a REPORT LUNS command is received.
Signed-off-by: NEwan D. Milne <emilne@redhat.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Tested-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Add power_status to SES device slot, so we can power on/off the
HDDs behind the enclosure.

Check firmware status in ses_set_* before sending control pages to
firmware.
Signed-off-by: NSong Liu <songliubraving@fb.com>
Acked-by: NDan Williams <dan.j.williams@intel.com>
Reviewed-by: NJens Axboe <axboe@fb.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The name provided by firmware is in a vendor specific format, publish
the slot number to have a reliable mechanism for identifying slots
across firmware implementations.  If the enclosure does not provide a
slot number fallback to the component number which is guaranteed unique,
and usually mirrors the slot number.

Cleaned up the unused ses_component.desc in the process.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NSong Liu <songliubraving@fb.com>
Reviewed-by: NJens Axboe <axboe@fb.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Export the NAA logical id for the enclosure.  This is optionally
available from the sas_transport_class, but it is really a property of
the enclosure.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NSong Liu <songliubraving@fb.com>
Reviewed-by: NJens Axboe <axboe@fb.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

In support of a /dev/disk/by-slot populated with data from the enclosure
and ses modules udev needs notification when the new interface
files/links are available.  Otherwise, any udev rules specified for the
disk cannot assume that the enclosure topology has settled.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NSong Liu <songliubraving@fb.com>
Reviewed-by: NJens Axboe <axboe@fb.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>