Add sysfs ABI docs for driver entries bind, unbind and new_id.  These
entries are pretty old, from 2.6.0 onwards AFAIK, so this documents
current behaviour.
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJesse Barnes <jbarnes@hobbes.lan>

Clean up the sysfs interface to regulators by only exposing the
attributes that can be properly displayed.  For example: when a
particular regulator method is needed to display the value, only
create that attribute when that method exists.

This cleaned-up interface is much more comprehensible.  Most
regulators only support a subset of the possible methods, so
often more than half the attributes would be meaningless.  Many
"not defined" values are no longer necessary.  (But handling
of out-of-range values still looks a bit iffy.)

Documentation is updated to reflect that few of the attributes
are *always* present, and to briefly explain why a regulator may
not have a given attribute.

This adds object code, about a dozen bytes more than was removed
by the preceding patch, but saves a bunch of per-regulator data
associated with the now-removed attributes.  So there's a net
reduction in memory footprint.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Show node to memory section relationship with symlinks in sysfs

Add /sys/devices/system/node/nodeX/memoryY symlinks for all
the memory sections located on nodeX.  For example:
/sys/devices/system/node/node1/memory135 -> ../../memory/memory135
indicates that memory section 135 resides on node1.

Also revises documentation to cover this change as well as updating
Documentation/ABI/testing/sysfs-devices-memory to include descriptions
of memory hotremove files 'phys_device', 'phys_index', and 'state'
that were previously not described there.

In addition to it always being a good policy to provide users with
the maximum possible amount of physical location information for
resources that can be hot-added and/or hot-removed, the following
are some (but likely not all) of the user benefits provided by
this change.
Immediate:
  - Provides information needed to determine the specific node
    on which a defective DIMM is located.  This will reduce system
    downtime when the node or defective DIMM is swapped out.
  - Prevents unintended onlining of a memory section that was
    previously offlined due to a defective DIMM.  This could happen
    during node hot-add when the user or node hot-add assist script
    onlines _all_ offlined sections due to user or script inability
    to identify the specific memory sections located on the hot-added
    node.  The consequences of reintroducing the defective memory
    could be ugly.
  - Provides information needed to vary the amount and distribution
    of memory on specific nodes for testing or debugging purposes.
Future:
  - Will provide information needed to identify the memory
    sections that need to be offlined prior to physical removal
    of a specific node.

Symlink creation during boot was tested on 2-node x86_64, 2-node
ppc64, and 2-node ia64 systems.  Symlink creation during physical
memory hot-add tested on a 2-node x86_64 system.
Signed-off-by: NGary Hade <garyhade@us.ibm.com>
Signed-off-by: NBadari Pulavarty <pbadari@us.ibm.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The UWB radio manager coordinates the use of the radio between the
PALs that may be using it.  PALs request use of the radio with
uwb_radio_start() and the radio manager will start beaconing if its
not already doing so.  When the last PAL has called uwb_radio_stop()
beaconing will be stopped.

In the future, the radio manager will have a more sophisticated channel
selection algorithm, probably following the Channel Selection Policy
from the WiMedia Alliance when it is finalized.  For now, channel 9
(BG1, TFC1) is selected.

The user may override the channel selected by the radio manager and may
force the radio to stop beaconing.

The WUSB Host Controller PAL makes use of this and there are two new
debug PAL commands that can be used for testing.
Signed-off-by: NDavid Vrabel <david.vrabel@csr.com>

C2port implements a two wire serial communication protocol (bit
banging) designed to enable in-system programming, debugging, and
boundary-scan testing on low pin-count Silicon Labs devices.

Currently this code supports only flash programming through sysfs
interface but extensions shoud be easy to add.
Signed-off-by: NRodolfo Giometti <giometti@linux.it>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Introduce a new flag showing whether the event has an event handler/method.

For all the GPEs and Fixed Events,
 1. ACPI_EVENT_FLAG_HANDLE is cleared, it's an "invalid" ACPI event.
 2. Both ACPI_EVENT_FLAG_HANDLE and ACPI_EVENT_FLAG_DISABLE are set,
    it's "disabled".
 3. Both ACPI_EVENT_FLAG_HANDLE and ACPI_EVENT_FLAG_ENABLE are set,
    it's "enabled".
 4. Both ACPI_EVENT_FLAG_HANDLE and ACPI_EVENT_FLAG_WAKE_ENABLE are set,
    it's "wake_enabled".

Among other things, this prevents incorrect reporting of ACPI events
as being "invalid" when it's really just (temporarily) "disabled".
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

Create a new sysfs file per interface named supports_autosuspend.  This
file returns true if an interface driver's .supports_autosuspend flag is
set.  It also returns true if the interface is unclaimed (since the USB
core will autosuspend a device if an interface is not claimed).

This new sysfs file will be useful for user space scripts to test whether
a USB device correctly auto-suspends.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added basic support for a Delcom USB 7-segment LED Display

Signed-off by: Harrison Metzger <harrisonmetz@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Way too often, I have a machine that exhibits some kind of crappy
behavior.  The CPU looks wedged in the kernel or it is spending way too
much system time and I wonder what is responsible.

I try to run readprofile.  But, of course, Ubuntu doesn't enable it by
default.  Dang!

The reason we boot-time enable it is that it takes a big bufffer that we
generally can only bootmem alloc.  But, does it hurt to at least try and
runtime-alloc it?

To use:
echo 2 > /sys/kernel/profile

Then run readprofile like normal.

This should fix the compile issue with allmodconfig.  I've compile-tested
on a bunch more configs now including a few more architectures.
Signed-off-by: NDave Hansen <dave@linux.vnet.ibm.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Provide a new file 'name' in the regulator sysfs class with a human
readable name for the regulator for use in applications.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Additionally added another web resource for voltage regulators.
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Add some brief documentation on the UWB and WUSB related sysfs files.
Signed-off-by: NDavid Vrabel <david.vrabel@csr.com>

Provide summary ABI docs about the /sys/class/gpio files.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Document files in /sys/firmware/sgi_uv/.
Signed-off-by: NRuss Anderson <rja@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds documentation describing the sysfs ABI used by the regulator
framework.
Signed-off-by: NLiam Girdwood <lg@opensource.wolfsonmicro.com>

Memory may be hot-removed on a per-memory-block basis, particularly on
POWER where the SPARSEMEM section size often matches the memory-block
size.  A user-level agent must be able to identify which sections of
memory are likely to be removable before attempting the potentially
expensive operation.  This patch adds a file called "removable" to the
memory directory in sysfs to help such an agent.  In this patch, a memory
block is considered removable if;

o It contains only MOVABLE pageblocks
o It contains only pageblocks with free pages regardless of pageblock type

On the other hand, a memory block starting with a PageReserved() page will
never be considered removable.  Without this patch, the user-agent is
forced to choose a memory block to remove randomly.

Sample output of the sysfs files:

./memory/memory0/removable: 0
./memory/memory1/removable: 0
./memory/memory2/removable: 0
./memory/memory3/removable: 0
./memory/memory4/removable: 0
./memory/memory5/removable: 0
./memory/memory6/removable: 0
./memory/memory7/removable: 1
./memory/memory8/removable: 0
./memory/memory9/removable: 0
./memory/memory10/removable: 0
./memory/memory11/removable: 0
./memory/memory12/removable: 0
./memory/memory13/removable: 0
./memory/memory14/removable: 0
./memory/memory15/removable: 0
./memory/memory16/removable: 0
./memory/memory17/removable: 1
./memory/memory18/removable: 1
./memory/memory19/removable: 1
./memory/memory20/removable: 1
./memory/memory21/removable: 1
./memory/memory22/removable: 1
Signed-off-by: NBadari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Acked-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Provide new hugepages user APIs that are more suited to multiple hstates
in sysfs.  There is a new directory, /sys/kernel/hugepages.  Underneath
that directory there will be a directory per-supported hugepage size,
e.g.:

/sys/kernel/hugepages/hugepages-64kB
/sys/kernel/hugepages/hugepages-16384kB
/sys/kernel/hugepages/hugepages-16777216kB

corresponding to 64k, 16m and 16g respectively.  Within each
hugepages-size directory there are a number of files, corresponding to the
tracked counters in the hstate, e.g.:

/sys/kernel/hugepages/hugepages-64/nr_hugepages
/sys/kernel/hugepages/hugepages-64/nr_overcommit_hugepages
/sys/kernel/hugepages/hugepages-64/free_hugepages
/sys/kernel/hugepages/hugepages-64/resv_hugepages
/sys/kernel/hugepages/hugepages-64/surplus_hugepages

Of these files, the first two are read-write and the latter three are
read-only.  The size of the hugepage being manipulated is trivially
deducible from the enclosing directory and is always expressed in kB (to
match meminfo).

[dave@linux.vnet.ibm.com: fix build]
[nacc@us.ibm.com: hugetlb: hang off of /sys/kernel/mm rather than /sys/kernel]
[nacc@us.ibm.com: hugetlb: remove CONFIG_SYSFS dependency]
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a kobject to create /sys/kernel/mm when sysfs is mounted.  The kobject
will exist regardless.  This will allow for the hugepage related sysfs
directories to exist under the mm "subsystem" directory.  Add an ABI file
appropriately.

[kosaki.motohiro@jp.fujitsu.com: fix build]
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Why?:
There are occasions where userspace would like to access sysfs
attributes for a device but it may not know how sysfs has named the
device or the path.  For example what is the sysfs path for
/dev/disk/by-id/ata-ST3160827AS_5MT004CK?  With this change a call to
stat(2) returns the major:minor then userspace can see that
/sys/dev/block/8:32 links to /sys/block/sdc.

What are the alternatives?:
1/ Add an ioctl to return the path: Doable, but sysfs is meant to reduce
   the need to proliferate ioctl interfaces into the kernel, so this
   seems counter productive.

2/ Use udev to create these symlinks: Also doable, but it adds a
   udev dependency to utilities that might be running in a limited
   environment like an initramfs.

3/ Do a full-tree search of sysfs.

[kay.sievers@vrfy.org: fix duplicate registrations]
[kay.sievers@vrfy.org: cleanup suggestions]

Cc: Neil Brown <neilb@suse.de>
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: NKay Sievers <kay.sievers@vrfy.org>
Reviewed-by: NSL Baur <steve@xemacs.org>
Acked-by: NKay Sievers <kay.sievers@vrfy.org>
Acked-by: NMark Lord <lkml@rtr.ca>
Acked-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Allow users to enable/disable/clear a specific & valid GPE/Fixed Event
in user space.

This is useful for debugging, especially for some
interrupt storm issues.

All wakeup GPEs are disabled and they can not be enabled at runtime,
and we mark them as invalid.

All GPEs that don't have a _Lxx/_Exx method are marked as invalid.

All Fixed Events that don't have an event handler are marked as invalid
and they can't be enabled until an event handler is registered.
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLing Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Add modalias and subchannel type attributes for all subchannels.
I/O subchannel specific attributes are now created in
io_subchannel_probe(). modalias and subchannel type are also
added to the uevent for the css bus. Also make the css modalias
known.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

This patch adds /sys/firmware/memmap interface that represents the BIOS
(or Firmware) provided memory map. The tree looks like:

    /sys/firmware/memmap/0/start   (hex number)
                           end     (hex number)
                           type    (string)
    ...                 /1/start
                           end
                           type

With the following shell snippet one can print the memory map in the same form
the kernel prints itself when booting on x86 (the E820 map).

  --------- 8< --------------------------
    #!/bin/sh
    cd /sys/firmware/memmap
    for dir in * ; do
        start=$(cat $dir/start)
        end=$(cat $dir/end)
        type=$(cat $dir/type)
        printf "%016x-%016x (%s)\n" $start $[ $end +1] "$type"
    done
  --------- >8 --------------------------

That patch only provides the needed interface:

 1. The sysfs interface.
 2. The structure and enumeration definition.
 3. The function firmware_map_add() and firmware_map_add_early()
    that should be called from architecture code (E820/EFI, for
    example) to add the contents to the interface.

If the kernel is compiled without CONFIG_FIRMWARE_MEMMAP, the interface does
nothing without cluttering the architecture-specific code with #ifdef's.

The purpose of the new interface is kexec: While /proc/iomem represents
the *used* memory map (e.g. modified via kernel parameters like 'memmap'
and 'mem'), the /sys/firmware/memmap tree represents the unmodified memory
map provided via the firmware. So kexec can:

 - use the original memory map for rebooting,
 - use the /proc/iomem for setting up the ELF core headers for kdump
   case that should only represent the memory of the system.

The patch has been tested on i386 and x86_64.
Signed-off-by: NBernhard Walle <bwalle@suse.de>
Acked-by: NGreg KH <gregkh@suse.de>
Acked-by: NVivek Goyal <vgoyal@redhat.com>
Cc: kexec@lists.infradead.org
Cc: yhlu.kernel@gmail.com
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Fuse allocates a separate bdi for each filesystem, and registers them
in sysfs with "MAJOR:MINOR" of sb->s_dev (st_dev).  This works fine for
anon devices normally used by fuse, but can conflict with an already
registered BDI for "fuseblk" filesystems, where sb->s_dev represents a
real block device.  In particularl this happens if a non-partitioned
device is being mounted.

Fix by registering with a different name for "fuseblk" filesystems.

Thanks to Ioan Ionita for the bug report.
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
Reported-by: NIoan Ionita <opslynx@gmail.com>
Tested-by: NIoan Ionita <opslynx@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move BDI statistics to debugfs:

   /sys/kernel/debug/bdi/<bdi>/stats

Use postcore_initcall() to initialize the sysfs class and debugfs,
because debugfs is initialized in core_initcall().

Update descriptions in ABI documentation.
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add "max_ratio" to /sys/class/bdi.  This indicates the maximum percentage of
the global dirty threshold allocated to this bdi.

[mszeredi@suse.cz]

 - fix parsing in max_ratio_store().
 - export bdi_set_max_ratio() to modules
 - limit bdi_dirty with bdi->max_ratio
 - document new sysfs attribute
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Under normal circumstances each device is given a part of the total write-back
cache that relates to its current avg writeout speed in relation to the other
devices.

min_ratio - allows one to assign a minimum portion of the write-back cache to
a particular device.  This is useful in situations where you might want to
provide a minimum QoS.  (One request for this feature came from flash based
storage people who wanted to avoid writing out at all costs - they of course
needed some pdflush hacks as well)

max_ratio - allows one to assign a maximum portion of the dirty limit to a
particular device.  This is useful in situations where you want to avoid one
device taking all or most of the write-back cache.  Eg.  an NFS mount that is
prone to get stuck, or a FUSE mount which you don't trust to play fair.

Add "min_ratio" to /sys/class/bdi.  This indicates the minimum percentage of
the global dirty threshold allocated to this bdi.

[mszeredi@suse.cz]

 - fix parsing in min_ratio_store()
 - document new sysfs attribute
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Provide a place in sysfs (/sys/class/bdi) for the backing_dev_info object.
This allows us to see and set the various BDI specific variables.

In particular this properly exposes the read-ahead window for all relevant
users and /sys/block/<block>/queue/read_ahead_kb should be deprecated.

With patient help from Kay Sievers and Greg KH

[mszeredi@suse.cz]

 - split off NFS and FUSE changes into separate patches
 - document new sysfs attributes under Documentation/ABI
 - do bdi_class_init as a core_initcall, otherwise the "default" BDI
   won't be initialized
 - remove bdi_init_fmt macro, it's not used very much

[akpm@linux-foundation.org: fix ia64 warning]
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: NGreg KH <greg@kroah.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Vital Product Data (VPD) may be exposed by PCI devices in several
ways.  It is generally unsafe to read this information through the
existing interfaces to user-land because of stateful interfaces.

This adds:
- abstract operations for VPD access (struct pci_vpd_ops)
- VPD state information in struct pci_dev (struct pci_vpd)
- an implementation of the VPD access method specified in PCI 2.2
  (in access.c)
- a 'vpd' binary file in sysfs directories for PCI devices with VPD
  operations defined

It adds a probe for PCI 2.2 VPD in pci_scan_device() and release of
VPD state in pci_release_dev().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add /sysfs/firmware/ibft/[initiator|targetX|ethernetX] directories along with
text properties which export the the iSCSI Boot Firmware Table (iBFT)
structure.

What is iSCSI Boot Firmware Table?  It is a mechanism for the iSCSI tools to
extract from the machine NICs the iSCSI connection information so that they
can automagically mount the iSCSI share/target.  Currently the iSCSI
information is hard-coded in the initrd.  The /sysfs entries are read-only
one-name-and-value fields.

The usual set of data exposed is:

# for a in `find /sys/firmware/ibft/ -type f -print`; do  echo -n "$a: ";  cat $a; done
/sys/firmware/ibft/target0/target-name: iqn.2007.com.intel-sbx44:storage-10gb
/sys/firmware/ibft/target0/nic-assoc: 0
/sys/firmware/ibft/target0/chap-type: 0
/sys/firmware/ibft/target0/lun: 00000000
/sys/firmware/ibft/target0/port: 3260
/sys/firmware/ibft/target0/ip-addr: 192.168.79.116
/sys/firmware/ibft/target0/flags: 3
/sys/firmware/ibft/target0/index: 0
/sys/firmware/ibft/ethernet0/mac: 00:11:25:9d:8b:01
/sys/firmware/ibft/ethernet0/vlan: 0
/sys/firmware/ibft/ethernet0/gateway: 192.168.79.254
/sys/firmware/ibft/ethernet0/origin: 0
/sys/firmware/ibft/ethernet0/subnet-mask: 255.255.252.0
/sys/firmware/ibft/ethernet0/ip-addr: 192.168.77.41
/sys/firmware/ibft/ethernet0/flags: 7
/sys/firmware/ibft/ethernet0/index: 0
/sys/firmware/ibft/initiator/initiator-name: iqn.2007-07.com:konrad.initiator
/sys/firmware/ibft/initiator/flags: 3
/sys/firmware/ibft/initiator/index: 0

For full details of the IBFT structure please take a look at:
ftp://ftp.software.ibm.com/systems/support/system_x_pdf/ibm_iscsi_boot_firmware_table_v1.02.pdf

[akpm@linux-foundation.org: fix build]
Signed-off-by: NKonrad Rzeszutek <konradr@linux.vnet.ibm.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Peter Jones <pjones@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add ABI documentation for these files:

	/sys/fs/ocfs2/max_locking_protocol
	/sys/fs/ocfs2/loaded_cluster_plugins
	/sys/fs/ocfs2/active_cluster_plugin
	/sys/fs/ocfs2/cluster_stack
Signed-off-by: NJoel Becker <joel.becker@oracle.com>
Signed-off-by: NMark Fasheh <mfasheh@suse.com>

Update the documentation to reflect the change in userspace interface.
Signed-off-by: NJerome Marchand <jmarchan@redhat.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

The top-level Documentation/ directory is unmanageably large, so we
should take any obvious opportunities to move stuff into subdirectories.
These sched-*.txt files seem an obvious easy case.
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

See Documentation/ABI/testing/sysfs-firmware-acpi
Based-on-original-patch-by: NLuming Yu <luming.yu@intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

This documents two newly created files:
/sys/bus/usb/device/.../power/connected_duration
/sys/bus/usb/device/.../power/active_duration

Documentation was placed in Documentation/ABI/testing, since that's where the
documentation is for the other USB sysfs power files.
Signed-off-by: NSarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds documentation about /sys/kernel/uids/<uid>/cpu_share
to Documentation/ABI.
Signed-off-by: NDhaval Giani <dhaval@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as920) adds an extra level of protection to the
USB-Persist facility.  Now it will apply by default only to hubs; for
all other devices the user must enable it explicitly by setting the
power/persist device attribute.

The disconnect_all_children() routine in hub.c has been removed and
its code placed inline.  This is the way it was originally as part of
hub_pre_reset(); the revised usage in hub_reset_resume() is
sufficiently different that the code can no longer be shared.
Likewise, mark_children_for_reset() is now inline as part of
hub_reset_resume().  The end result looks much cleaner than before.

The sysfs interface is updated to add the new attribute file, and
there are corresponding documentation updates.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as874) adds another piece to the user-visible part of the
USB autosuspend interface.  The new power/level sysfs attribute allows
users to force the device on (with autosuspend off), force the device
to sleep (with autoresume off), or return to normal automatic operation.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as867) adds an entry for the new power/autosuspend
attribute in Documentation/ABI/testing, and it changes the behavior of
the delay value.  Now a delay of 0 means to autosuspend as soon as
possible, and negative values will prevent autosuspend.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- update documentation

- use clear_bdi_congested/set_bdi_congested functions directly instead of
  old wrappers

- removed DECLARE_BUF_AS_STRING macro
Signed-off-by: NThomas Maier <balagi@justmail.de>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>