enable the spi nor for imx6sl-evk boards.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

add a pinctrl for ECSPI1. This pinctrl can be used in the imx6sl-evk board.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The pwm-node is missing its #pwm-cells property. The pwm-framework will
complain about this.

Add the missing property.
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This is needed for SD3.0 cards working on UHS mode.
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch adds support for lvds backlight on boards
i.MX6q-SabreSD and i.MX6dl-SabreSD
Signed-off-by: NRogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Currently we get the following errors on imx51-babbage:

/display@di0: could not find display-timings node
/display@di0: no timings specified
/display@di1: could not find display-timings node
/display@di1: no timings specified
imx-drm imx-drm: failed to allocate buffer with size 0

Provide timing values for IPU1, which is connected to a DVI bridge and
to IPU2, which can be connected to the WVGA panel, so that both of them can
be functional.

While at it, disable the WVGA panel, so that DVI output becomes the default one.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NGwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NGwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

On the mx53qsb board with mc34708 PMIC, GPIO1_8 resets the system, so better not
to use it as a wakeup source.

Use GPIO 2_14 and 2_15 for wakeup sources instead.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

SDHC1 does not have any GPIO for reading the card detection status, so
remove 'cd-gpios'.

After this change card detection works via the internal SD controller mechanism.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

SDHC3 is 8 bit-wide, so pass the bus-width property to reflect that.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This board is based on the M28 SoM with custom baseboard. Supported
are LEDs, ethernet, PWM, LCD, SD slots.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

GPIO3_29 is used to reset the ethernet phy.

Add support for it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

GPIO1_25 is used to reset the ethernet phy.

Add support for it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

MX6QDL_PAD_EIM_D23__GPIO3_IO23 pin is used to reset the ethernet phy.

Add it to the 'hog' group.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add pcie device node for imx6qdl.
Signed-off-by: NSean Cross <xobs@kosagi.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

For more information about the Udoo board:
http://www.udoo.org/Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add pinmux for 4-bit SD card connected to SSP2.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add initial PHYTEC VF610 Cosmic/Cosmic+ board support with
UART and FEC enabled.
Signed-off-by: NMatt Porter <matt.porter@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This pin definition had been added after the initial patch to use
symbolic pin names in DTS files.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Update the Ka-Ro TX28 DTS file.

- add Copyright header
- use label references for better readability
- sort the entries alphabetically
- add some aliases used by U-Boot to modify the DT data
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

For some reason, the select input of pin function USB_OTG_ID is not
implemented via a regular select input register but using the bit
USB_OTG_ID_ SEL (shift 13) of IOMUXC_GPR1 register (offset 0x4).

As per the workaround for such quirk implemented in pinctrl driver,
we need to compose the input_val cell as below.

	31     23      15      7        0
	| 0xff | shift | width | select |

Thus, we have 0xff0d0100 for MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID and
0xff0d0101 for MX6QDL_PAD_GPIO_1__USB_OTG_ID in input_val cell.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Tested-by: NPeter Chen <peter.chen@freescale.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Convert mx23/mx28 dts files to use the padconfig defintions from
mxs-pinfunc.h.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Convert mx23/mx28 dts filed to use the pinctrl header files.

NOTE: During automatic conversion of these files to use the pinconfig
definitions an inconsistency has been found in:
arch/arm/boot/dts/imx28-apx4devkit.dts

According to the comment the function for pad SSP2_SS0 should have
been MX28_PAD_SSP2_SS0__GPIO_2_19, while the given value 0x2131
represents: MX28_PAD_SSP2_SS0__AUART3_TX

I used the later (though probably wrong) definition because that's
what is actually being used in the DTB.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Remove the list of possible pin configurations from the documentation
file and create header files containing those definitions.
This eliminates the need for error-prone manual lookup of those values
in the documentation and guarantees consistency between the human
readable representation of the pad function in the .dts file and the
actual binary value used in DT.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Provide 'lradc-touchscreen-wires' property to the LRADC driver, so that
touchscreen can be functional.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

On imx6qdl-sabresd the SDHC2 and SDHC3 are 8 bit-wide, so pass the bus-width
property to reflect that.

Otherwise the mmc driver will operate with the default bus-width value of 4.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This is needed for supporting ultra high speed cards like SD3.0 cards.
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add spi aliases.

While at it, keep the aliases entries sorted.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Enable USB function for OTG 1 and OTG 2 at mx6sololite evk.
Besides, fix the wrong interrupt number for OTG2 and host 1.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add iomuxc gpr device node for imx6sl.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: NNicolin Chen <b42378@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch enables DSPI0 and at26df081a flash device for Vybrid VF610
TOWER board.
Signed-off-by: NChao Fu <b44548@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add Freescale DSPI node into vf610 dts.
Signed-off-by: NChao Fu <b44548@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

imx6q-sabrelite board can be connected to a 1024x768 Hannstar LVDS panel.

Add support for it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Put the nodes in alphabetical order so that further node additions can be better
organized.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Trying to use the usb otg port on mx53qsb results in the following error:

$ modprobe g_ether
using random self ethernet address
using random host ethernet address
usb0: HOST MAC 52:0f:8a:1e:aa:09
usb0: MAC de:f3:70:d8:6c:62
using random self ethernet address
using random host ethernet address
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready

(Connect the USB cable)

$ ci_hdrc ci_hdrc.0: remove, state 4
usb usb1: USB disconnect, device number 1
ci_hdrc ci_hdrc.0: USB bus 1 deregistered
ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11

USB otg port goes to connector J3 (mini USB) and also to the USB combo (J2).

As mx53qsb does not provide a USB ID pin, pass the dr_mode as 'peripheral' so
that we can have usb device working.

Tested via g_ether.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Testing g_ether results in the following:

[    1.648022] using random self ethernet address
[    1.652778] using random host ethernet address
[    1.660504] usb0: HOST MAC c6:28:6a:81:dc:ff
[    1.666360] usb0: MAC 7e:81:54:16:c0:c6
[    1.670504] using random self ethernet address
[    1.675842] using random host ethernet address
[    1.682655] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[    1.689332] g_ether gadget: g_ether ready
[    3.328974] irq 237: nobody cared (try booting with the "irqpoll" option)
[    3.335831] CPU: 0 PID: 1 Comm: swapper Not tainted 3.11.0-rc6-next-20130819 #1035
[    3.343500] [<c0014258>] (unwind_backtrace+0x0/0xf0) from [<c0011b20>] (show_stack+0x10/0x14)
[    3.352098] [<c0011b20>] (show_stack+0x10/0x14) from [<c006af4c>] (__report_bad_irq+0x20/0xc0)
[    3.360763] [<c006af4c>] (__report_bad_irq+0x20/0xc0) from [<c006b3f4>] (note_interrupt+0x1d4/0x234)
[    3.369943] [<c006b3f4>] (note_interrupt+0x1d4/0x234) from [<c0069754>] (handle_irq_event_percpu+0xc4/0x268)
[    3.379815] [<c0069754>] (handle_irq_event_percpu+0xc4/0x268) from [<c0069934>] (handle_irq_event+0x3c/0x5c)
[    3.389686] [<c0069934>] (handle_irq_event+0x3c/0x5c) from [<c006bb78>] (handle_level_irq+0x8c/0xe8)
[    3.398865] [<c006bb78>] (handle_level_irq+0x8c/0xe8) from [<c0068ff0>] (generic_handle_irq+0x20/0x30)
[    3.408213] [<c0068ff0>] (generic_handle_irq+0x20/0x30) from [<c000fc9c>] (handle_IRQ+0x30/0x84)
[    3.417040] [<c000fc9c>] (handle_IRQ+0x30/0x84) from [<c0012564>] (__irq_svc+0x44/0x54)
[    3.425094] [<c0012564>] (__irq_svc+0x44/0x54) from [<c0020244>] (__do_softirq+0x90/0x268)
[    3.433400] [<c0020244>] (__do_softirq+0x90/0x268) from [<c00207d4>] (irq_exit+0x9c/0xd8)
[    3.441619] [<c00207d4>] (irq_exit+0x9c/0xd8) from [<c000fca0>] (handle_IRQ+0x34/0x84)
[    3.449577] [<c000fca0>] (handle_IRQ+0x34/0x84) from [<c0012564>] (__irq_svc+0x44/0x54)
[    3.457629] [<c0012564>] (__irq_svc+0x44/0x54) from [<c04602b0>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[    3.467164] [<c04602b0>] (_raw_spin_unlock_irqrestore+0x34/0x44) from [<c0348298>] (input_register_handler+0x98/0xb4)
[    3.477835] [<c0348298>] (input_register_handler+0x98/0xb4) from [<c064bc10>] (mousedev_init+0x30/0x60)
[    3.487275] [<c064bc10>] (mousedev_init+0x30/0x60) from [<c00088ac>] (do_one_initcall+0xe8/0x154)
[    3.496198] [<c00088ac>] (do_one_initcall+0xe8/0x154) from [<c062aabc>] (kernel_init_freeable+0xf0/0x1b4)
[    3.505810] [<c062aabc>] (kernel_init_freeable+0xf0/0x1b4) from [<c0456550>] (kernel_init+0x8/0xe4)
[    3.514899] [<c0456550>] (kernel_init+0x8/0xe4) from [<c000ee60>] (ret_from_fork+0x14/0x34)
[    3.523263] handlers:
[    3.525578] [<c0339d14>] ci_irq
[    3.528757] Disabling IRQ #237

Provide the USB0_ID pin in the usb0 node, so that g_ether can operate
correctly.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Tested via g_ether:

$ modprobe g_ether
using random self ethernet address
using random host ethernet address
usb0: HOST MAC 42:b5:26:a9:48:21
usb0: MAC 36:a6:85:9b:9e:13
using random self ethernet address
using random host ethernet address
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
$ g_ether gadget: high-speed config #1: CDC Ethernet (ECM)
$ ifconfig usb0 10.0.0.2

Then on the PC host side:

~$ sudo ifconfig usb0 10.0.0.1
~$ ping 10.0.0.2
PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data.
64 bytes from 10.0.0.2: icmp_req=1 ttl=64 time=1.26 ms
64 bytes from 10.0.0.2: icmp_req=2 ttl=64 time=0.280 ms
64 bytes from 10.0.0.2: icmp_req=3 ttl=64 time=0.297 ms
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch adds the missing W1 (onewire) devicetree node for i.MX51 CPUs.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>