mac_config() can be called at any point, and the expected behaviour
from MAC drivers is to only reprogram when necessary - and certainly
avoid taking the link down on every call.

Unfortunately, mvpp2 does exactly that - it takes the link down, and
reprograms everything, and then releases the forced-link down.

This is bad, it can cause the link to bounce:

- SFP detects signal, disables LOS indication.
- SFP code calls into phylink, calling phylink_sfp_link_up() which
  triggers a resolve.
- phylink_resolve() calls phylink_get_mac_state() and finds the MAC
  reporting link up.
- phylink wants to configure the pause mode on the MAC, so calls
  phylink_mac_config()
- mvpp2 takes the link down temporarily, generating a MAC link down
  event followed by another MAC link event.
- phylink calls mac_link_up() and then processes the MAC link down
  event.
- phylink_resolve() gets called again, registers the link down, and
  calls mach_link_down() before re-running itself.
- phylink_resolve() starts again at step 3 above.  This sequence
  repeats.

GMAC versions prior to mvpp2 do not require the link to be taken down
except when certain link properties (eg, switching between SGMII and
1000base-X mode, or enabling/disabling in-band negotiation) are
changed.  Implement this for mvpp2.
Tested-by: NSven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It appears that the mvpp22 can get stuck with SGMII negotiation.  The
symptoms are that in-band negotiation never completes and the partner
(eg, PHY) never reports SGMII link up, or if it supports negotiation
bypass, goes into negotiation bypass mode (which will happen when the
PHY sees that the MAC is alive but gets no response.)

Triggering the PHY end of the link to re-negotiate results in the
bypass bit clearing on the PHY, and then re-setting - indicating that
the problem is at the mvpp22 GMAC end.

Asserting the GMAC reset and de-asserting it resolves the issue.
Arrange to assert the GMAC reset at probe time, and deassert it only
after we have configured the GMAC for the appropriate mode.  This
resolves the issue.
Tested-by: NSven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sven Auhagen reported issues with negotiation on a couple of his
platforms using a mixture of SFP and PHYs in various different
modes.  Debugging to root cause proved difficult, but essentially
the problem comes down to the mvpp2 phylink implementation being
slightly at odds with what is expected.

phylink operates in three modes: phy, fixed-link, and in-band mode.

In the first two modes, the expected behaviour from a MAC driver is
that phylink resolves the operating mode and passes the mode to the
MAC driver for it to program, including when the link should be
brought up or taken down.  This is basically the same as the libphy
approach.  This does not negate the requirement to advertise a correct
control word for interface modes that have control words where that
can be reasonably controlled.

The second mode is in-band mode, where the MAC is expected to use the
in-band control word to determine the operating mode.

The mvneta driver implements the correct pattern required to support
this: configure the port interface type separately from the in-band
mode(s).  This is now specified in the phylink documentation patches.

mvpp2 was programming in-band mode for SGMII and the 802.3z modes no
what, and avoided forcing the link up in fixed/phy modes.  This caused
a problem with some boards where the PHY is by default programmed to
enter AN bypass mode, the PHY would report that the link was up, but
the mvpp2 never completed the exchange of control word.

Another issue that mvpp2 has is it sets SGMII AN format control word
for both SGMII and 802.3z modes. The format of the control word is
defined by MVPP2_GMAC_INBAND_AN_MASK, which should be set for SGMII
and clear for 802.3z. Available Marvell documentation for earlier
GMAC implementations does not make this clear, but this has been
ascertained via extensive testing on earlier GMAC implementations,
and then confirmed with a Macchiatobin Single Shot connected to a
Clearfog: when MVPP2_GMAC_INBAND_AN_MASK is set, the clearfog does
not receive the advertised pause mode settings.

Lastly, there is no flow control in the in-band control word in Cisco
SGMII, setting the flow control autonegotiation bit even with a PHY
that has the Marvell extension to send this information does not result
in the flow control being enabled at the MAC.  We need to do this
manually using the information provided via phylink.

Re-code mvpp2's mac_config() and mac_link_up() to follow this pattern.
This allows Sven Auhagen's board and Macchiatobin to reliably bring
the link up with the 88e1512 PHY with phylink operating in PHY mode
with COMPHY built as a module but the rest of the networking built-in,
and u-boot having brought up the interface.  in-band mode requires an
additional patch to resolve another problem.
Tested-by: NSven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

Notice that, in this case, variable size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)

Notice that, in this case, variable size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

size = struct_size(instance, entry, count);

This code was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

Notice that, in this case, variable size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    void *entry[];
};

size = sizeof(struct foo) + count * sizeof(void *);
instance = alloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = alloc(struct_size(instance, entry, count), GFP_KERNEL);

Notice that, in this case, variable size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)

Notice that, in this case, variable alloc_size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)

Notice that, in this case, variable fsz is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds driver support to query SmartAN capability via ethtool.
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds driver interface to read the SmartAN capability from
management firmware.
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new compatibility string for this product. It's using
at91sam9260-macb layout but has a newer hardware revision: it's safer
to use its own string.
Signed-off-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As vregion rehash is happening in delayed work, add some visibility to
the process using a few tracepoints.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Expose new driver-specific "acl_region_rehash_interval" devlink param
which would allow user to alter default ACL region rehash interval.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the hints are returned, the migration should be started. For that to
happen, there is a need to create a second physical region in TCAM with
new ERP set by passing the hints and then move chunk by chunk,
entry by entry.

During the transition, two lookups will occur. One in old region and
another in new region. The highest priority rule will be chosen.

In an unlikely case that the migration will fail and also rollback to
original region will fail the vregion will become in bad state.
Everything will work, only no future rehash will be possible. In a
follow-up work, this can be resolved by trying to resume the rollback
in delayed work and repair the vregion.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For Spectrum-2 this allows parallel lookups in multiple regions.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hints priv comes from ERP code and it is possible to obtain it from
TCAM code. Add arg to appropriate functions so the hints
priv could be passed back down to ERP code. Pass NULL now as the
follow-up patches would pass an actual hints priv pointer.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce an initial implementation of rehash logic in ERP code.
Currently, the rehash is considered as needed only in case number of
roots in the hints is smaller than the number of roots actually in use.
In that case return hints pointer and let it be obtained through the
callpath through the Spectrum-2 TCAM op.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do the split of entry struct so the new entry struct is related to the
actual HW entry, whereas ventry struct is a SW abstration of that.
This split prepares possibility for ventry to hold 2 HW entries which
is needed for region ERP rehash flow.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do the split of chunk struct so the new chunk struct is related to the
actual HW chunk (differs between Spectrum and Spectrum-2),
whereas vchunk struct is a SW abstraction of that. This split
prepares possibility for vchunk to hold 2 HW chunks which is needed
for region ERP rehash flow.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do the split of region struct so the new region struct is related to the
actual HW region, whereas vregion struct is a SW abstration of that.
This split prepares possibility for vregion to hold 2 HW regions which
is needed for region ERP rehash flow.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement simple greedy algo to find more optimized root-delta tree for
a given objagg instance. This "hints" can be used by a driver to:
1) check if the hints are better (driver's choice) than the original
   objagg tree. Driver does comparison of objagg stats and hints stats.
2) use the hints to create a new objagg instance which will construct
   the root-delta tree according to the passed hints. Currently, only a
   simple greedy algorithm is implemented. Basically it finds the roots
   according to the maximal possible user count including deltas.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, user can do dump or get of param values right after the
devlink params are registered. However the driver may not be initialized
which is an issue. The same problem happens during notification
upon param registration. Allow driver to publish devlink params
whenever it is ready to handle get() ops. Note that this cannot
be resolved by init reordering, as the "driverinit" params have
to be available before the driver is initialized (it needs the param
values there).
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Static checker warning complains on uninitialized variable:

        drivers/net/ethernet/netronome/nfp/flower/action.c:618 nfp_fl_pedit()
        error: uninitialized symbol 'idx'.

Which is actually never used from the functions that take it as
parameter. Remove it.

Fixes: 73867881 ("drivers: net: use flow action infrastructure")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPaul Fox <pfox@solarflare.com>
Signed-off-by: NBert Kenward <bkenward@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the common phy binding, so that we can reconfigure the
comphy according to the desired ethernet speed.  This will allow us to
support 1000base-X and 2500base-X SFPs dynamically on SolidRun Clearfog.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With this patch, ndo_tx_timeout callback will be redirected to the tx
reporter in order to detect a tx timeout error and report it to the
devlink health. (The watchdog detects tx timeouts, but the driver verify
the issue still exists before launching any recover method).

In addition, recover from tx timeout in case of lost interrupt was added
to the tx reporter recover method. The tx timeout recover from lost
interrupt is not a new feature in the driver, this patch re-organize the
functionality and move it to the tx reporter recovery flow.

tx timeout example:
(with auto_recover set to false, if set to true, the manual recover and
diagnose sections are irrelevant)

$cat /sys/kernel/debug/tracing/trace
...
devlink_health_report: bus_name=pci dev_name=0000:00:09.0
driver_name=mlx5_core reporter_name=tx: TX timeout on queue: 0, SQ: 0x8a,
CQ: 0x35, SQ Cons: 0x2 SQ Prod: 0x2, usecs since last trans: 14912000

$devlink health show
pci/0000:00:09.0:
  name tx
    state healthy #err 1 #recover 0 last_dump_ts N/A
    parameters:
      grace_period 500 auto_recover false

$devlink health diagnose pci/0000:00:09.0 reporter tx -j -p
{
    "SQs": [ {
            "sqn": 138,
            "HW state": 1,
            "stopped": true
        },{
            "sqn": 142,
            "HW state": 1,
            "stopped": false
        } ]
}

$devlink health diagnose pci/0000:00:09.0 reporter tx
SQs:
  sqn: 138 HW state: 1 stopped: true
  sqn: 142 HW state: 1 stopped: false

$devlink health recover pci/0000:00:09 reporter tx
$devlink health show
pci/0000:00:09.0:
  name tx
    state healthy #err 1 #recover 1 last_dump_ts N/A
    parameters:
      grace_period 500 auto_recover false
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: NMoshe Shemesh <moshe@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add mlx5e tx reporter to devlink health reporters. This reporter will be
responsible for diagnosing, reporting and recovering of tx errors.
This patch declares the TX reporter operations and creates it using the
devlink health API. Currently, this reporter supports reporting and
recovering from send error CQE only. In addition, it adds diagnose
information for the open SQs.

For a local SQ recover (due to driver error report), in case of SQ recover
failure, the recover operation will be considered as a failure.
For a full tx recover, an attempt to close and open the channels will be
done. If this one passed successfully, it will be considered as a
successful recover.

The SQ recover from error CQE flow is not a new feature in the driver,
this patch re-organize the functions and adapt them for the devlink
health API. For this purpose, move code from en_main.c to a new file
named reporter_tx.c.

Diagnose output:
$devlink health diagnose pci/0000:00:09.0 reporter tx -j -p
{
    "SQs": [ {
            "sqn": 138,
            "HW state": 1,
            "stopped": false
        },{
            "sqn": 142,
            "HW state": 1,
            "stopped": false
        } ]
}

$devlink health diagnose pci/0000:00:09.0 reporter tx
SQs:
  sqn: 138 HW state: 1 stopped: false
  sqn: 142 HW state: 1 stopped: false
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: NMoshe Shemesh <moshe@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EMAC driver had a custom IBM_EMAC_RX_SKB_HEADROOM
Kconfig option that reserved additional skb headroom for RX.
This patch removes the option and migrates the code
to use napi_alloc_skb() and netdev_alloc_skb_ip_align()
in its place.
Signed-off-by: NChristian Lamparter <chunkeey@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

8c56df37 ("net: add support for Cavium PTP coprocessor") added the
Cavium PTP coprocessor driver and enabled it by default.  Remove the
"default y" because the driver only applies to Cavium ThunderX processors.

Fixes: 8c56df37 ("net: add support for Cavium PTP coprocessor")
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in sbdma_tx_process() when
skb xmit done. It makes drop profiles(dropwatch, perf) more
friendly.
Signed-off-by: NYang Wei <yang.wei9@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in velocity_free_tx_buf()
when skb xmit done. It makes drop profiles(dropwatch, perf) more
friendly.
Signed-off-by: NYang Wei <yang.wei9@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in bdx_tx_cleanup() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: NYang Wei <yang.wei9@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: NYang Wei <yang.wei9@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in mpc52xx_fec_tx_interrupt()
when skb xmit done. It makes drop profiles(dropwatch, perf) more
friendly.
Signed-off-by: NYang Wei <yang.wei9@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in epic_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: NYang Wei <yang.wei9@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in de_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: NYang Wei <yang.wei9@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current driver only enables Pdelay_Req and Pdelay_Resp when
HWTSTAMP_FILTER_PTP_V2_EVENT, HWTSTAMP_FILTER_PTP_V1_L4_EVENT or
HWTSTAMP_FILTER_PTP_V2_L4_EVENT is requested. This results in ptp sync on
slave mode to report 'received SYNC without timestamp' when using ptp4l.

Although the hardware can support Sync, Pdelay_Req and Pdelay_resp by
setting bit14 annd bits 17/16 to 01 this leaves Delay_Req timestamps out.

Fix this by enabling all event and general messages timestamps.
This includes SYNC, Follow_Up, Delay_Req, Delay_Resp, Pdelay_Req,
Pdelay_Resp and Pdelay_Resp_Follow_Up messages.
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: NJose Abreu <joabreu@synopsys.com>
Tested-by: NAlexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some case, we may use multiple pedit actions to modify packets.
The command shown as below: the last pedit action is effective.

$ tc filter add dev netdev_rep parent ffff: protocol ip prio 1    \
	flower skip_sw ip_proto icmp dst_ip 3.3.3.3        \
	action pedit ex munge ip dst set 192.168.1.100 pipe    \
	action pedit ex munge eth src set 00:00:00:00:00:01 pipe    \
	action pedit ex munge eth dst set 00:00:00:00:00:02 pipe    \
	action csum ip pipe    \
	action tunnel_key set src_ip 1.1.1.100 dst_ip 1.1.1.200 dst_port 4789 id 100 \
	action mirred egress redirect dev vxlan0

To fix it, we add max_mod_hdr_actions to mlx5e_tc_flow_parse_attr struction,
max_mod_hdr_actions will store the max pedit action number we support and
num_mod_hdr_actions indicates how many pedit action we used, and store all
pedit action to mod_hdr_actions.

Fixes: d79b6df6 ("net/mlx5e: Add parsing of TC pedit actions to HW format")
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NTonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>