Before commit 99724c18 ("mlxsw: spectrum: Introduce support for
router interfaces") we used to assign vFIDs to the created vPorts. Since
these vPorts were used for slow path traffic we had to disable learning
for them, as it doesn't make sense to have it enabled.

This is no longer the case and now vPorts are either used for router
interfaces (for which learning is disabled by the firmware) or bridge
ports (for which learning is explicitly enabled by the driver).

Therefore, we can remove the learning configuration upon vPort creation.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We now offload the learning configuration to the device and don't rely
on the driver to decide whether to learn the FDB record, so remove the
check.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up until now we simply stored the learning configuration of a bridge
port in the driver and decided whether to learn a new FDB record based
on this value.

However, this is sub-optimal in cases where learning is disabled on the
bridge port, as the device repeatedly generates learning notifications
for the same record.

Instead, offload the learning configuration to the device, thereby
preventing it from generating notifications when learning is disabled.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are going to prevent the device from generating learning
notifications for a port that was configured with learning disabled.

Since learning configuration is done per {Port, VID} we need to apply
the port's learning configuration for any VID that is added to the
bridge port's VLAN filter list.

When a VID is added to the VLAN filter list of a VLAN-aware bridge port,
configure the {Port, VID} learning status according to the port's
configuration. When the VID is removed, disable learning for the {Port,
VID}.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When removing VLANs from the VLAN-aware bridge we shouldn't abort on the
first error, as we'll otherwise have resources that will never be freed.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 05978481 ("mlxsw: spectrum: Create PVID vPort before
registering netdevice") removed __mlxsw_sp_port_vlans_del() from the
init sequence of the driver, which forced it to be non-symmetric with
regards to __mlxsw_sp_port_vlans_add().

Make both functions symmetric as the constraint no longer exists.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up until now a learning session ended whenever the number of queried
records was zero. This turned out to be problematic in situations where
a large number of MACs (48K) had to be processed by the switch driver,
as RTNL mutex is held during the learning session.

Instead, limit the number of FDB records that can be processed in a
session to 64. This means that every time the device is queried for
learning notifications (currently, every 100ms), up to 64 records will
be processed by the switch driver.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the return type of ena_set_push_mode() to be void,
as it always returns 0.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove including <linux/version.h> that don't need it.
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add provision for configuring the fastpath queues with Tx (or Rx) only
functionality.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we disable SRIOV, we used to unregister the netdev but wasn't
freed. But next time when the same netdev is registered, since the state
was in 'NETREG_UNREGISTERED', we used to hit BUG_ON in register_netdevice,
where it expects the state to be 'NETREG_UNINITIALIZED'.

Alloc netdev and register them while configuring SRIOV, and free them
when SRIOV is disabled. Also added a new function to setup ethernet
properties instead of using ether_setup. Set carrier off by default,
since we don't have to do any transmit on the interface.

Fixes: 7829451c ("cxgb4: Add control net_device for configuring PCIe VF")
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

liquidio_set_rxcsum_command is a local function only, no need to expose
it outside of lio_main.c so declare it static and make sparse happy.
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These ops allow to control number of channels driver is allowed to
work with at cpdma level. The maximum number of channels is 8 for
rx and 8 for tx. In dual_emac mode the h/w channels are shared
between two interfaces and changing number on one interface changes
number of channels on another.

How many channels are supported and enabled:
$ ethtool -l ethX

Change number of channels (up to 8)
$ ethtool -L ethX rx 6 tx 6

Per-channel statistic:
$ ethtool -S ethX
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Keep the driver internals in C file. Currently it's not required for
drivers to know rx or tx a channel is, except create function.
So correct "channel create" function, and use all channel struct
macroses only for internal use.
Reviewed-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cpsw h/w supports up to 8 tx and 8 rx channels. This patch adds
multi-queue support to the driver only, shaper configuration will
be added with separate patch series. Default shaper mode, as
before, priority mode, but with corrected priority order, 0 - is
highest priority, 7 - lowest.

The poll function handles all unprocessed channels, till all of
them are free, beginning from hi priority channel.

In dual_emac mode the channels are shared between two network devices,
as it's with single-queue default mode.

The statistic for every channel can be read with:
$ ethtool -S ethX
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The interrupts shouldn't be disabled while receiving skb, but while
ctrl_stop, the channels are stopped and all remaining packets are
handled with netif_receive_skb(), it can cause WARN_ONCE when ctrl
is stopping while not all packets were handled with NAPIs:

lock_irq_save
    cpdma_ctlr_stop
       cpdma_chan_top
           __cpdma_chan_free
               cpsw_rx_handler
                   netif_receive_skb

So, split locking while ctrl stop thus interrupts are still
enabled while skbs handling. It can cause WARN_ONCE in rare
cases when ctrl is stopping while not all packets were handled
with NAPIs.
Reviewed-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tx channels share same pool of descriptors. Thus one channel can
block another if pool is emptied by one. But, the shaper should
decide which channel is allowed to send packets. To avoid such
impact of one channel on another, let every channel to have its
own piece of pool.
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement set_tx_maxrate NDO to perform per queue tx rate limiting.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to bind/unbind specified tx queues to/from scheduling
classes.  If a queue is already bound to a scheduling class, it is
unbound first and then bound to a new specified class.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to create tx traffic scheduling classes with specified
scheduling parameters.  Return an existing class if a match is found
with same scheduling parameters.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each VF employees a lock that's supposed to serialize its usage of the
HW channel for communication with its PF, but the critical section is
ill-defined:

  - VFs currently release the lock whenever the PF response arrives,
    prior to actually processing the reply buffer [which was also supposed
    to have been protected by same lock].

  - The lock would be released on first response, ignoring the possibilty
    the sw flow isn't over [as might be the case of the acquisition flow].
    As a result, the flow would run unprotected and would cause a double
    mutex release [as the additional message completion would release it
    while its actually already free].

Change the flow to have a dedicated function to be called at end of each
flow and release the lock.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modern VFs can't run on old non-compatible as the fastpath HSI is
slightly changed - but as the HSI is actually very close [basically,
a single bit whose meaning flipped] this can be supported with small
modifications.

The major differences would be in:
  - Recognizing that VF is running on top of a legacy PF.
  - Returning some slowpath configurations that are no longer needed
    on top of modern PFs, but would be required when working over
    the legacy ones.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware would silently drop any control frame sent by VF to prevent
a malicious VF from generating pause flood in the network.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 8.10.x FW added support for forward compatability as well as
'future' backward compatibility, but only to those VFs that were
using HSI which was 8.10.x based or newer.

The latest firmware now supports backward compatibility for the
older VFs based on 8.7.x and 8.8.x firmware as well.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* Reuse existing functionality from memdup_user() instead of keeping
  duplicate source code.

  This issue was detected by using the Coccinelle software.

* Return directly if this copy operation failed.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify the return expression.
Signed-off-by: NWei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy_dev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the new copper device X557.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This shouldn't matter as nothing should be attached still to be
consisted control MDIO speed for these devices as well.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The X557 devices use a different interface to the LED for the port.
This patch reflect that change.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add geneve Rx offload support for x550em_a.

The implementation follows the vxlan code with the lower 16 bits of
the VXLANCTRL register holding the UDP port for VXLAN and the upper
for Geneve.

Disabled NFS filters in the RFCTL register which allows us to simplify
the check for VXLAN and Geneve packets in ixgbe_rx_checksum().

Removed vxlan from the name of the callback functions and replaced it
with udp_tunnel which is more in line with the new API.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The PF driver was only receiving the first 4 bytes of the MAC due
to an incorrect size parameter for ixgbevf_write_msg_read_ack()
in ixgbevf_set_rar_vf().

Correct the size by calculating it on a fly for all instances where
we call ixgbevf_write_msg_read_ack()
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ethtool reports backplane type interfaces as 1000/10000baseT link modes.
This has been corrected to report the media as KR, KX or KX4 based on the backplane interface present.
Signed-off-by: NVeola Nazareth <veola.nazareth@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

RDMA client is closed during the PF reset and needs to be opened again.
Setting the flag so that RDMA client is opened in watchdog() function.

Change-ID: I507b1e4cbd05528cdff68fd360ef3dcac8901263
Signed-off-by: NAvinash Dayanand <avinash.dayanand@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Several defines and code comments were indented with spaces instead
of tabs, correct the issue to make indentation consistent.

Change-ID: I0dc6bbb990ec4a9e856acc9ec526d876181f092c
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>

Correcting the mutex usage, in client_subtask(), mutex_unlock has
to be called just before client_del_instance() since this function opens
and later closes the same mutex again.
Similarly in client_is_registered removing the mutex since it closes
the mutex twice.

This is a patch suggested by RDMA team.

Change-ID: Icce519c266e4221b8a2a72a15ba5bf01750e5852
Signed-off-by: NAvinash Dayanand <avinash.dayanand@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use __stringify instead.
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The function i40e_client_release has a print statement that uses an
adapter pointer which is not initialized if a previous if statement
is not true. Hence, intialize it in the right place.

Change-ID: I1afdaa2c46771ac42be56edcc41bb56b455b06c8
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>