This patch is to add some basic functions to support umd
P-state function for vangogh.
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to enable the fine grain tuning function for renoir.
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to add the fine grain tuning function for renoir.
This function uses the pp_od_clk_voltage sysfs file to configure the min
and max value of gfx clock frequency manually or restore the default value.

Command guide:
echo "s level value" > pp_od_clk_voltage
        "s" - set the sclk frequency
        "level" - 0 or 1, "0" represents the min value,  "1" represents
        the max value
        "value" - the target value of sclk frequency, it should
        be limited in the safe range
echo "r" > pp_od_clk_voltage
        "r" - reset the sclk frequency, restore the default value instantly
echo "c" > pp_od_clk_voltage
        "c" - commit the min and max value of sclk frequency to the system
        only after the commit command, the target values set by "s" command
        will take effect.
Example:
1)change power profile from "auto" to "standard"
        $ cat power_dpm_force_performance_level
        auto
        $ echo "profile_standard" > power_dpm_force_performance_level
        $ cat power_dpm_force_performance_level
        profile_standard
2)check the default sclk frequency
        $ cat pp_od_clk_voltage
        OD_SCLK:
        0:        200Mhz
        1:       1400Mhz
        OD_RANGE:
        SCLK:     200MHz       1400MHz
3)use "s" -- set command to configure the min and max sclk frequency
        $ echo "s 0 600" > pp_od_clk_voltage
        $ echo "s 1 1000" > pp_od_clk_voltage
        $ echo "c" > pp_od_clk_voltage
        $ cat pp_od_clk_voltage
        OD_SCLK:
        0:        600Mhz
        1:       1000Mhz
        OD_RANGE:
        SCLK:     200MHz       1400MHz
4)use "r" -- reset command to restore the min or max sclk frequency
        $ echo "r" > pp_od_clk_voltage
        $ cat pp_od_clk_voltage
        OD_SCLK:
        0:        200Mhz
        1:       1400Mhz
        OD_RANGE:
        SCLK:     200MHz       1400MHz
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

sienna cichlid interfaces with RAS eeprom on I2C controller port 1
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NJohn Clements <john.clements@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to improve the fine grain tuning function for RV/RV2/PCO.
This patch adds two new commands: "restore" and "commit".
This function uses the pp_od_clk_voltage sysfs file to configure the min
and max value of gfx clock frequency manually or restore the default value.

Command guide:
echo "s level value" > pp_od_clk_voltage
        "s" - set the sclk frequency
        "level" - 0 or 1, "0" represents the min value,  "1" represents
        the max value
        "value" - the target value of sclk frequency, it should be limited in the
        safe range
echo "r" > pp_od_clk_voltage
        "r" - reset the sclk frequency, restore the default value instantly
echo "c" > pp_od_clk_voltage
        "c" - commit the min and max value of sclk frequency to the system
        only after the commit command, the target values set by "s" command
        will take effect.
Example:
1)change power profile from "auto" to "manual"
        $ cat power_dpm_force_performance_level
        auto
        $ echo "manual" > power_dpm_force_performance_level
        $ cat power_dpm_force_performance_level
        manual
2)check the default sclk frequency
        $ cat pp_od_clk_voltage
        OD_SCLK:
        0:        200Mhz
        1:       1400Mhz
        OD_RANGE:
        SCLK:     200MHz       1400MHz
3)use "s" -- set command to configure the min and max sclk frequency
        $ echo "s 0 600" > pp_od_clk_voltage
        $ echo "s 1 1000" > pp_od_clk_voltage
        $ echo "c" > pp_od_clk_voltage
        $ cat pp_od_clk_voltage
        OD_SCLK:
        0:        600Mhz
        1:       1000Mhz
        OD_RANGE:
        SCLK:     200MHz       1400MHz
4)use "r" -- reset command to restore the min or max sclk frequency
        $ echo "r" > pp_od_clk_voltage
        $ cat pp_od_clk_voltage
        OD_SCLK:
        0:        200Mhz
        1:       1400Mhz
        OD_RANGE:
        SCLK:     200MHz       1400MHz
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to enable the "fetch" function of pp_dpm_vclk and
pp_dpm_dclk.
It allows to fetch the current frequency of vcn and dcn and their
DPM levels for vangogh.
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Acked-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to add two new sysfs nodes for vangogh:
pp_dpm_dclk and pp_dpm_vclk.
The two sysfs nodes are similar to pp_dpm_fclk/memclk/socclk.
pp_dpm_dclk represents the DPM frequency of dcn unit.
pp_dpm_vclk represents the DPM frequency of vcn unit.
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Acked-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to add new feature map macros to resolve duplicate name.
Vangogh uses one different format to name some feature bits of swSMU, it
causes some duplicate name in the existing feature map list.
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Acked-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to add supoort to umd P-state function for vangogh.
It enables the "fetch" function of 3 sysfs nodes: pp_dpm_mclk,
pp_dpm_fclk, pp_dpm_socclk,the function is used to fetch
the current frequency of memclk/fclk/socclk.
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Acked-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to correct the sensor value of power for vangogh.
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

the psp access ih path is not needed in navi
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NJane Jian <Jane.Jian@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Adjust a jump target so that a bit of exception handling can be better
reused at the end of this function.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

* Return directly after a call of the function “kzalloc” failed
  at the beginning.

* Delete a label which became unnecessary with this refactoring.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We can have the same src ids for different client ids so make sure to
check both the client id and the source id when handling interrupts.
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We need to take into account the client id otherwise we'll end
up sending generic events for any src id that is registered.

We only support irq domains on pre-soc15 parts so client is
always legacy.
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

tear down software ih ring and its state.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

software ih ring is enabled in vega10 and navi
ih block by default.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

software ih ring will be used as a workaround
in case hardware ih ring 1 and ring 2 don't work
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This is supported by Sienna Cichlid, Navy Flounder and Dimgrey
Cavefish. For these ASICs, the target voltage calculation can be
illustrated by "voltage = voltage calculated from v/f curve +
overdrive vddgfx offset".

V2: limit the smu_version check for Sienna Cichlid only

Here are some sample usages about this new OD setting:
1. Check current vddgfx offset setting by
cat /sys/class/drm/card0/device/pp_od_clk_voltage
...
...
OD_VDDGFX_OFFSET:
0mV
...
...

2. Set new vddgfx offset by
echo "vo 10" > /sys/class/drm/card0/device/pp_od_clk_voltage
cat /sys/class/drm/card0/device/pp_od_clk_voltage
...
...
OD_VDDGFX_OFFSET:
10mV
...
...
3. Commit the new setting by
echo "c" > /sys/class/drm/card0/device/pp_od_clk_voltage
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Enable Sienna Cichlid gfxclk/uclk overdrive support.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Populate the bootup overdrive table settings.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When user specifies a reduced WGP(CU) config via disalbe_cu module
parameter, this does not disable the clocks which uses additional
power. This interface send active WGP number to SMU and SMU will
cooperate with RLC to power off relative WGPs.

v2: Add request active WGPs in Vangogh smu post init.
Signed-off-by: NJinzhou.Su <Jinzhou.Su@amd.com>
Reviewed-by: NJiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: NLijo Lazar <lijo.lazar@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Documents the hooks in struct pptable_funcs.

v2: Improved documentation accuracy.
v3: Improved set_default_od_settings() definition.
Signed-off-by: NRyan Taylor <Ryan.Taylor@amd.com>
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

APUs don't support ih ring 1 and ring 2.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

For all the ASICs that integrate psp v11, vega20
doesn't support ih reroute. arcturus and later will
allow kernel driver to program ih_cfg_index/data
through mmio directly. navi1x and onwards will only
support grb_ih_set command in sriov configuration.

psp_v11_0_reroute_ih is not needed any more.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

except for RENOIR, it is not correct to have
IH_CHICKEN programming in vega10 ih block.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

IH_CHICKEN.MC_SPACE_FBPA_ENABLE field is only
valid when IH_RB_CNTL.MC_SPACE is programed to 0x3,
frame buffer physical address. For both bus address
and gpu virtual address, don't program MC_SPACE_FBPA_ENABLE
field
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

already switched to vega20 ih block for vega20
and arcturus. no need to add vega20 support in
navi10 ih block
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

replace navi10 ih block with vega20 ih block for
vega20 and arcturus
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

in case page faults overwhlem the interrupt handlers
and the driver lost the valuable interrupt information
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

vega20 ih blocks will be used for vega20/arcturus
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

v1: add osssys v4_2 register offset and shift masks
header files. vega20 and arcturus will refer to
these ip headers. (Hawking)
v2: clean up osssys v4_2 registers (Alex)
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>

The iv format is the same for all the soc15 adpater
and onwards and can share a common function to
decode iv.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

since from soc15, all the chips share the same
iv format. create a common helper to decode iv
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

all the ih rb control register offsets are cached
at the beginning of navi10 ih_sw_init.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

use navi10_ih_enable_ring to enable all the
available ring buffers for navi1x and onwards
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

replace ih_enable_interrupts and ih_disable_interrupts
with ih_toggle_interrupts
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Initialize ih control registers offset through helper
function navi10_ih_init_register_offset.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

navi10_ih_toggle_ring_interrupts will be used to
enable/disable an ih ring interrupts for navi1x
and onwards
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

navi10_ih_enable_ring will be used to enable an
ih ring for navi1x and onwards
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>