This patch (as1599) fixes dummy-hcd to make it update the appropriate
driver pointer when a new gadget driver is bound or unbound.  Without
this change, the gadget driver's name doesn't appear in dev_printk
output.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The lpc32xx_udc driver supported only one controller by defining a global
static struct for it. This patch enables multiple instances of the controller
by dynamic allocation of the struct at probe(). A static struct is kept as a
template on initialization since it does some complex preset, reflecting fixed
hardware endpoint structure.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch removes the utilization of struct usb_endpoint_descriptor, as done
by other drivers also. This was done on request by the USB gadget maintainers,
since this API is obsoleted.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adjusts the LPC32xx USB gadget driver to the new udc_start /
udc_stop interface.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When IORESOURCE_IRQ_SHAREABLE is set, the irq handler may be called
even if the interupt of the USB module doesn't happen. So, it may
clear the interrupt flags by mistake. This patch fixes it.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

%pm already provides pretty print for mac addresses, let's
use that and drop homebrew mac address printing.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

usb_gadget_remove_driver() runs through a four-step sequence to shut down
the gadget driver.  For the case of a composite gadget + at91 UDC, this
would look like:

    udc->driver->disconnect(udc->gadget);          // composite_disconnect()
    usb_gadget_disconnect(udc->gadget);            // at91_pullup(gadget, 0)
    udc->driver->unbind(udc->gadget);              // composite_unbind()
    usb_gadget_udc_stop(udc->gadget, udc->driver); // at91_stop()

The UDC driver can receive SETUP packets from the host up until the
point when usb_gadget_disconnect() returns.  On rare occasions, the
gadget driver may see this sequence:

    udc->driver->disconnect(udc->gadget);          // composite_disconnect()
    udc->driver->setup(udc->gadget, &ctrl);        // composite_setup()
    udc->driver->unbind(udc->gadget);              // composite_unbind()

Some gadget drivers, such as composite, assume this will never happen
and crash as a result.

The fix is to quiesce the UDC hardware (via usb_gadget_disconnect)
before running the gadget driver through the disconnect/unbind sequence.
Reviewed-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The timeout values were 1000 and timeout issue occured many times on my
s3c6410 Soc based board (mostly when booting whith USB cable not
connected). This patch increase the values to 10000 to guarantee the
success of reset.

Having set timeout to 10000, I printed the remained timeout values
which could cause timeout issue before this change (tested several
times).
the first timeout value remained:
	timeout = 8079
	timeout = 8079
	timeout = 8078
	timeout = 8081
the second timeout value remained:
	timeout = 7940
	timeout = 7945
	timeout = 7940
	timeout = 7938
Seeing from above values, I think the value 10000 is big enough.
Signed-off-by: NDu, Changbin <changbin.du@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The lockdep hunter mentions a non consistent usage of spin_lock and
spin_lock_irqsafe in the composite_disconnect and usb_function_activate
function:

[   15.700897] =================================
[   15.705255] [ INFO: inconsistent lock state ]
[   15.709617] 3.5.0-rc5+ #413 Not tainted
[   15.713453] ---------------------------------
[   15.717812] inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
[   15.723822] uvc-gadget/116 [HC1[1]:SC0[0]:HE0:SE1] takes:
[   15.729222]  (&(&cdev->lock)->rlock){?.+...}, at: [<7f0049e8>] composite_disconnect+0x2c/0x74 [g_webcam]
[   15.738797] {HARDIRQ-ON-W} state was registered at:
[   15.743677]   [<8006de3c>] mark_lock+0x148/0x688
[   15.748325]   [<8006ecb0>] __lock_acquire+0x934/0x1b74
[   15.753481]   [<8007047c>] lock_acquire+0x98/0x138
[   15.758288]   [<804c776c>] _raw_spin_lock+0x4c/0x84
[   15.763188]   [<7f006ae4>] usb_function_activate+0x28/0x94 [g_webcam]
[   15.769652]   [<7f00820c>] usb_ep_autoconfig_reset+0x78/0x98 [g_webcam]
[   15.776287]   [<7f0082a4>] uvc_v4l2_open+0x78/0x94 [g_webcam]
[   15.782054]   [<80366a38>] v4l2_open+0x104/0x130
[   15.786697]   [<800efd30>] chrdev_open+0xa0/0x170
[   15.791423]   [<800e9718>] do_dentry_open.isra.13+0x1e8/0x264
[   15.797186]   [<800ea5d4>] nameidata_to_filp+0x58/0x94
[   15.802340]   [<800fa29c>] do_last.isra.31+0x2a0/0x808
[   15.807497]   [<800faa40>] path_openat+0xc8/0x3e8
[   15.812216]   [<800fae90>] do_filp_open+0x3c/0x90
[   15.816936]   [<800ea6fc>] do_sys_open+0xec/0x184
[   15.821655]   [<800ea7c4>] sys_open+0x30/0x34
[   15.826027]   [<8000e5c0>] ret_fast_syscall+0x0/0x48
[   15.831015] irq event stamp: 6048
[   15.834330] hardirqs last  enabled at (6047): [<804c81b8>] _raw_spin_unlock_irqrestore+0x40/0x54
[   15.843132] hardirqs last disabled at (6048): [<8000e174>] __irq_svc+0x34/0x60
[   15.850370] softirqs last  enabled at (5940): [<80028380>] __do_softirq+0x188/0x270
[   15.858043] softirqs last disabled at (5935): [<80028944>] irq_exit+0xa0/0xa8
[   15.865195]
[   15.865195] other info that might help us debug this:
[   15.871724]  Possible unsafe locking scenario:
[   15.871724]
[   15.877645]        CPU0
[   15.880091]        ----
[   15.882537]   lock(&(&cdev->lock)->rlock);
[   15.886659]   <Interrupt>
[   15.889278]     lock(&(&cdev->lock)->rlock);
[   15.893573]
[   15.893573]  *** DEADLOCK ***
[   15.893573]
[   15.899496] no locks held by uvc-gadget/116.
[   15.903765]
[   15.903765] stack backtrace:
[   15.908125] Backtrace:
[   15.910604] [<80012038>] (dump_backtrace+0x0/0x114) from [<804bf8a4>] (dump_stack+0x20/0x24)
[   15.919043]  r6:dfb8e6f0 r5:dfb8e400 r4:809717ec r3:60000193
[   15.924766] [<804bf884>] (dump_stack+0x0/0x24) from [<804c0c0c>] (print_usage_bug+0x258/0x2c0)
[   15.933388] [<804c09b4>] (print_usage_bug+0x0/0x2c0) from [<8006e240>] (mark_lock+0x54c/0x688)
[   15.942006] [<8006dcf4>] (mark_lock+0x0/0x688) from [<8006edb8>] (__lock_acquire+0xa3c/0x1b74)
[   15.950625] [<8006e37c>] (__lock_acquire+0x0/0x1b74) from [<8007047c>] (lock_acquire+0x98/0x138)
[   15.959418] [<800703e4>] (lock_acquire+0x0/0x138) from [<804c78fc>] (_raw_spin_lock_irqsave+0x58/0x94)
[   15.968736] [<804c78a4>] (_raw_spin_lock_irqsave+0x0/0x94) from [<7f0049e8>] (composite_disconnect+0x2c/0x74 [g_webcam])
[   15.979605]  r7:00000012 r6:df82b0c4 r5:ded755bc r4:ded75580
[   15.985331] [<7f0049bc>] (composite_disconnect+0x0/0x74 [g_webcam]) from [<8033c170>] (_gadget_stop_activity+0xc4/0x120)
[   15.996200]  r6:df82b0c4 r5:df82b0c8 r4:df82b0d0 r3:7f0049bc
[   16.001919] [<8033c0ac>] (_gadget_stop_activity+0x0/0x120) from [<8033e390>] (udc_irq+0x724/0xcb8)
[   16.010877]  r6:df82b010 r5:00000000 r4:df82b010 r3:00000000
[   16.016595] [<8033dc6c>] (udc_irq+0x0/0xcb8) from [<8033baec>] (ci_irq+0x64/0xdc)
[   16.024086] [<8033ba88>] (ci_irq+0x0/0xdc) from [<80086538>] (handle_irq_event_percpu+0x74/0x298)
[   16.032958]  r5:807fd414 r4:df38fdc0
[   16.036566] [<800864c4>] (handle_irq_event_percpu+0x0/0x298) from [<800867a8>] (handle_irq_event+0x4c/0x6c)
[   16.046315] [<8008675c>] (handle_irq_event+0x0/0x6c) from [<80089318>] (handle_level_irq+0xbc/0x11c)
[   16.055447]  r6:def04000 r5:807fd414 r4:807fd3c0 r3:00020000
[   16.061166] [<8008925c>] (handle_level_irq+0x0/0x11c) from [<80085cc8>] (generic_handle_irq+0x38/0x4c)
[   16.070472]  r5:807f7f64 r4:8081e9f8
[   16.074082] [<80085c90>] (generic_handle_irq+0x0/0x4c) from [<8000ef98>] (handle_IRQ+0x5c/0xbc)
[   16.082788] [<8000ef3c>] (handle_IRQ+0x0/0xbc) from [<800085cc>] (tzic_handle_irq+0x6c/0x9c)
[   16.091225]  r8:00000000 r7:def059b0 r6:00000001 r5:00000000 r4:00000000
r3:00000012
[   16.099141] [<80008560>] (tzic_handle_irq+0x0/0x9c) from [<8000e184>] (__irq_svc+0x44/0x60)
[   16.107494] Exception stack(0xdef059b0 to 0xdef059f8)
[   16.112550] 59a0:                                     00000001 00000001 00000000 dfb8e400
[   16.120732] 59c0: 40000013 81a2e500 00000000 81a2e500 00000000 00000000 80862418 def05a0c
[   16.128912] 59e0: def059c8 def059f8 80070e24 804c81bc 20000013 ffffffff
[   16.135542] [<804c8178>] (_raw_spin_unlock_irqrestore+0x0/0x54) from [<8003d0ec>] (__queue_work+0x108/0x470)
[   16.145369]  r5:dfb1a30c r4:81b93c00
[   16.148978] [<8003cfe4>] (__queue_work+0x0/0x470) from [<8003d4e0>] (queue_work_on+0x4c/0x54)
[   16.157511] [<8003d494>] (queue_work_on+0x0/0x54) from [<8003d544>] (queue_work+0x30/0x34)
[   16.165774]  r6:df2e6900 r5:80e0c2f8 r4:dfb1a2c8 r3:def04000
[   16.171495] [<8003d514>] (queue_work+0x0/0x34) from [<80493284>] (rpc_make_runnable+0x9c/0xac)
[   16.180113] [<804931e8>] (rpc_make_runnable+0x0/0xac) from [<80493c88>] (rpc_execute+0x40/0xa8)
[   16.188811]  r5:def05ad4 r4:dfb1a2c8
[   16.192426] [<80493c48>] (rpc_execute+0x0/0xa8) from [<8048c734>] (rpc_run_task+0xa8/0xb4)
[   16.200690]  r8:00000001 r7:df74f520 r6:ded75700 r5:def05ad4 r4:dfb1a2c8
r3:00000002
[   16.208618] [<8048c68c>] (rpc_run_task+0x0/0xb4) from [<801f1608>] (nfs_initiate_read+0xb4/0xd4)
[   16.217403]  r5:df3e86c0 r4:00000000
[   16.221015] [<801f1554>] (nfs_initiate_read+0x0/0xd4) from [<801f1c64>] (nfs_generic_pg_readpages+0x9c/0x114)
[   16.230937] [<801f1bc8>] (nfs_generic_pg_readpages+0x0/0x114) from [<801f0744>] (__nfs_pageio_add_request+0xe8/0x214)
[   16.241545]  r8:000bf000 r7:00000000 r6:00000000 r5:deef4640 r4:def05c1c
r3:801f1bc8
[   16.249463] [<801f065c>] (__nfs_pageio_add_request+0x0/0x214) from [<801f0e3c>] (nfs_pageio_add_request+0x28/0x54)
[   16.259818] [<801f0e14>] (nfs_pageio_add_request+0x0/0x54) from [<801f1394>] (readpage_async_filler+0x114/0x170)
[   16.269992]  r5:def05c58 r4:80fd7300
[   16.273607] [<801f1280>] (readpage_async_filler+0x0/0x170) from [<800bb418>] (read_cache_pages+0xa0/0x108)
[   16.283259]  r8:00200200 r7:00100100 r6:df74f654 r5:def05cd0 r4:80fd7300
[   16.290034] [<800bb378>] (read_cache_pages+0x0/0x108) from [<801f218c>] (nfs_readpages+0xc4/0x168)
[   16.298999] [<801f20c8>] (nfs_readpages+0x0/0x168) from [<800bb1d0>] (__do_page_cache_readahead+0x254/0x354)
[   16.308833] [<800baf7c>] (__do_page_cache_readahead+0x0/0x354) from [<800bb5d0>] (ra_submit+0x38/0x40)
[   16.318145] [<800bb598>] (ra_submit+0x0/0x40) from [<800bb6b0>] (ondemand_readahead+0xd8/0x3b0)
[   16.326851] [<800bb5d8>] (ondemand_readahead+0x0/0x3b0) from [<800bba20>] (page_cache_async_readahead+0x98/0xa8)
[   16.337043] [<800bb988>] (page_cache_async_readahead+0x0/0xa8) from [<800b2118>] (generic_file_aio_read+0x5b4/0x7c4)
[   16.347565]  r6:00000000 r5:df74f654 r4:80fd70a0
[   16.352231] [<800b1b64>] (generic_file_aio_read+0x0/0x7c4) from [<801e82c0>] (nfs_file_read+0x7c/0xcc)
[   16.361544] [<801e8244>] (nfs_file_read+0x0/0xcc) from [<800eab80>] (do_sync_read+0xb4/0xf4)
[   16.369981]  r9:00000000 r8:def05f70 r7:00000000 r6:00000000 r5:dec34900
r4:fffffdee
[   16.377896] [<800eaacc>] (do_sync_read+0x0/0xf4) from [<800eb548>] (vfs_read+0xb4/0x144)
[   16.385987]  r8:00000000 r7:def05f70 r6:76a95008 r5:003e3dd6 r4:dec34900
[   16.392761] [<800eb494>] (vfs_read+0x0/0x144) from [<800eb624>] (sys_read+0x4c/0x78)
[   16.400504]  r8:00000000 r7:00000003 r6:003e3dd6 r5:76a95008 r4:dec34900
[   16.407279] [<800eb5d8>] (sys_read+0x0/0x78) from [<8000e5c0>] (ret_fast_syscall+0x0/0x48)
[   16.415543]  r9:def04000 r8:8000e864 r6:000086b4 r5:00000000 r4:00000000
[   20.872729]  gadget: high-speed config #1: Video
[   20.877368]  gadget: uvc_function_set_alt(0, 0)
[   20.881908]  gadget: uvc_function_set_alt(1, 0)
[   20.891464]  gadget: uvc_function_set_alt(1, 0)
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix boot up hang when enable udc without otg enabled.
The root cause is that the clock will be shut down when probe routine is
finished because of clock gating. When a gadget driver is registered at
this time, it will call mv_udc_start which in turn will call
mv_udc_vbus_session. If there is no cable attached at the boot up time,
the vbus is low, so it will call stop_activity path without clock
enabled which will cause system hang then.
Actually, we need't go this path when clock is disabled, what we need to
do is just jump out.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix system hang in udc shutdown routine which caused by accessing usb
register when clock is disabled. So enable usb clock before access
register.
Signed-off-by: NYunfan Zhang <yfzhang@marvell.com>
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In order to support iso, we need do the following things:
1. fix length for one dtd
2. allow req contains multiple packets for a ISO transfer
Signed-off-by: NChao Xie <chao.xie@marvell.com>
Signed-off-by: NYu Xu <yuxu@marvell.com>
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

According to ChipIdea's reference manual in section 8.5.2
"Non-streaming operational mode in device mode", we'd better enable stream
mode, especially that ISO endpoints are not supported when the SDIS bit
is set.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

build_dtd() can be called when hold a spinlock, but GFP_KERNEL may cause
dma_pool_alloc() sleep, So we need use GFP_ATOMIC instead of GFP_KERNEL.
But using GFP_ATOMIC may cause failure when allocating memory, add error
handler to handle it.
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Clean unused code for mv_udc driver.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There are several places use udelay(LOOPS_USEC) to wait the status to be
changed, but the delay interval is a bit too long, so reduce it to
enhance the performance.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Following a report of a crash during an automount expire I found that
the locking in fs/autofs4/expire.c:get_next_positive_subdir() was wrong.
Not only is the locking wrong but the function is more complex than it
needs to be.

The function is meant to calculate (and dget) the next entry in the list
of directories contained in the root of an autofs mount point (an autofs
indirect mount to be precise). The main problem was that the d_lock of
the owner of the list was not being taken when walking the list, which
lead to list corruption under load. The only other lock that needs to
be taken is against the next dentry candidate so it can be checked for
usability.
Signed-off-by: NIan Kent <raven@themaw.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull VFIO fix from Alex Williamson:
 "Just a trivial patch to include vfio.h in the installed headers so we
  can complete userspace integration into QEMU."

* tag 'vfio-for-v3.6-rc1' of git://github.com/awilliam/linux-vfio:
  vfio: Include vfio.h in installed headers

Pull fuse updates from Miklos Szeredi.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: verify all ioctl retry iov elements
  fuse: add missing INIT flag descriptions
  fuse: add missing INIT flags
  fuse: update attributes on aio_read
  fuse: invalidate inode mapping if mtime changes
  fuse: add FUSE_AUTO_INVAL_DATA init flag

Merge tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen fix from Konrad Rzeszutek Wilk:
 "Way back in v3.5 we added a mechanism to populate back pages that were
  released (they overlapped with MMIO regions), but neglected to reserve
  the proper amount of virtual space for extend_brk to work properly.

  Coincidentally some other commit aligned the _brk space to larger area
  so I didn't trigger this until it was run on a machine with more than
  2GB of MMIO space."

 * On machines with large MMIO/PCI E820 spaces we fail to boot b/c
   we failed to pre-allocate large enough virtual space for extend_brk.

* tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/p2m: Reserve 8MB of _brk space for P2M leafs when populating back.

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
  sh: intc: Handle domain association for sparseirq pre-allocated vectors.
  sh: sh7269: Fix LCD pinmux
  sh: dma: fix request_irq usage

Moved to djbw@fb.com

Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: NDan Williams <djbw@fb.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When dumping "Code: " sections from an oops, the trapping instruction
%rip points to can be a string copy

  2b:*  f3 a5                   rep movsl %ds:(%rsi),%es:(%rdi)

and the line contain a bunch of ":".  Current "cut" selects only the and
the second field output looks funnily overlaid this:

  2b:*  f3 a5                   rep movsl %ds     <-- trapping instruction:(%rsi),%es:(%rdi

Fix this by selecting the remaining fields too.

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kbuild@vger.kernel.org
Signed-off-by: NBorislav Petkov <borislav.petkov@amd.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull two slave-dmaengine fixes from Vinod Koul:
 "One fixes the correct use of clock API in imx driver and the other
  enables clock for tegra driver, which is used for other tegra driver
  conversion to dmanegine in -next."

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dma: tegra: enable/disable dma clock
  dma: imx-dma: Fix kernel crash due to missing clock conversion

Pull more drm fixes from Dave Airlie:
 "Just some intel and nouveau ones this time, intel has more edp panel
  fixes for macbooks and nouveau has a suspend/resume regression fix in
  there."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: Apply post-sync write for pipe control invalidates
  drm/i915: reorder edp disabling to fix ivb MacBook Air
  drm/nv86/fifo: suspend fix
  drm/nouveau: disable copy engine on NVAF
  nouveau: fixup scanout enable in nvc0_pm
  drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
  drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
  drm/i915: ensure i2c adapter is all set before adding it
  drm/i915: ignore eDP bpc settings from vbt
  drm/i915: Fix blank panel at reopening lid
  drm/nve0/fifo: add support for the flip completion swmthd

Pull two sparc fixes from David S. Miller.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Be less verbose during vmemmap population.
  sparc64: do not clobber personality flags in sys_sparc64_personality()

* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
  drm/nv86/fifo: suspend fix
  drm/nouveau: disable copy engine on NVAF
  nouveau: fixup scanout enable in nvc0_pm
  drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
  drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
  drm/nve0/fifo: add support for the flip completion swmthd

Daniel Vetter writes:

"A few important fixers:
- fix various lvds backlight issues, regressed in 3.6 (Takashi Iwai)
- make the retina mbp work (ignore bogus edp bpc value in vbt)
- fix a gmbus regression introduced in (iirc) 3.4 (Jani Nikula)
- fix an edp panel power sequence regression, fixes the new macbook air
- apply the tlb invalidate w/a

Otherwise we still have another gmbus regression (patches are awaiting
tested-bys) and there's something odd going with some rare systems not
entering rc6 often enough (and hence blowing through too much power).  It
seems to be a timing-related issue and can be mitigated by frobbing the
magic tuning parameters. We're still working on that one. Also, we still
have some fallout from the hw context support, but you can only hit that
with mesa master."

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: Apply post-sync write for pipe control invalidates
  drm/i915: reorder edp disabling to fix ivb MacBook Air
  drm/i915: ensure i2c adapter is all set before adding it
  drm/i915: ignore eDP bpc settings from vbt
  drm/i915: Fix blank panel at reopening lid

On a 2-node machine with 256GB of ram we get 512 lines of
console output, which is just too much.

This mimicks Yinghai Lu's x86 commit c2b91e2e
(x86_64/mm: check and print vmemmap allocation continuous) except that
we aren't ever going to get contiguous block pointers in between calls
so just print when the virtual address or node changes.

This decreases the output by an order of 16.

Also demote this to KERN_DEBUG.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When invalidating the TLBs it is documentated as requiring a post-sync
write. Failure to do so seems to result in a GPU hang.

Exposure to this hang on IVB seems to be a result of removing the extra
stalls required for SNB pipecontrol workarounds:

commit 6c6cf5aa
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Fri Jul 20 18:02:28 2012 +0100

    drm/i915: Only apply the SNB pipe control w/a to gen6

Note: Manually switch the pipe_control cmd to 4 dwords to avoid a
(silent) functional conflict with -next. This way will get a loud (but
conflict with next (since the scratch_addr has been deleted there).

Reported-and-tested-by: yex.tian@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53322Acked-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: added note about merge conflict with -next.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

eDP is tons of fun. It turns out that at least the new MacBook Air 5,1
model absolutely doesn't like the new force vdd dance we've introduced
in

commit 6cb49835
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Sun May 20 17:14:50 2012 +0200

    drm/i915: enable vdd when switching off the eDP panel

But that patch also tried to fix some neat edp sequence issue with the
force_vdd timings. Closer inspection reveals that we've raised
force_vdd only to do the aux channel communication dp_sink_dpms. If we
move the edp_panel_off below that, we don't need any force_vdd for the
disable sequence, which makes the Air happy.

Unfortunately the reporter of the original bug that the above commit
fixed is travelling, so we can't test whether this regresses things.
But my theory is that since we don't check for any power-off ->
force_vdd-on delays in edp_panel_vdd_on, this was the actual
root-cause of this failure. With that force_vdd dance completely
eliminated, I'm hopeful the original bug stays fixed, too.

For reference the old bug, which hopefully doesn't get broken by this:

https://bugzilla.kernel.org/show_bug.cgi?id=43163

In any case, regression fixers win over plain bugfixes, so this needs
to go in asap.

v2: The crucial pieces seems to be to clear the force_vdd flag
uncoditionally, too, in edp_panel_off. Looks like this is left behind
by the firmware somehow.

v3: The Apple firmware seems to switch off the panel on it's own, hence
we still need to keep force_vdd on, but properly clear it when switching
the panel off.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45671Tested-by: NRoberto Romer <sildurin@gmail.com>
Tested-by: NDaniel Wagner <wagi@monom.org>
Tested-by: NKeith Packard <keithp@keithp.com>
Cc: stable@vger.kernel.org
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Pull s390 patches from Martin Schwidefsky:
 "Included are bug fixes and a patch to enable system call filtering
  with BPF."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/compat: fix mmap compat system calls
  s390/compat: fix compat wrappers for process_vm system calls
  s390: do not clobber personality flags in sys_32_personality()
  s390/seccomp: add support for system call filtering using BPF
  s390/sclp_sdias: Add missing break and "fall through"
  s390/mm: remove MAX_PHYSADDR_BITS define

Pull drm fixes from Dave Airlie:
 "Radeon and intel fixes mostly, one fix to the mgag200 driver to not
  hang on certain server variants."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (32 commits)
  drm/radeon: fix typo in function header comment
  drm/radeon/kms: implement timestamp userspace query (v2)
  drm/radeon/kms: add MSAA texture support for r600-evergreen
  drm/radeon/kms: reorder code in r600_check_texture_resource
  drm/radeon: fence virtual address and free it once idle v4
  drm/radeon: fix some missing parens in asic macros
  drm/radeon: add some new SI pci ids
  drm/radeon: fix ordering in pll picking on dce4+
  drm/radeon: do not reenable crtc after moving vram start address
  drm/radeon: fix bank tiling parameters on cayman
  drm/radeon: fix bank tiling parameters on evergreen
  drm/radeon: fix bank tiling parameters on SI
  drm/radeon: properly handle crtc powergating
  drm/radeon: properly handle SS overrides on TN (v2)
  drm/radeon/dce4+: set a more reasonable cursor watermark
  drm/radeon: fix handling for ddc type 5 on combios
  drm/mgag200: fix G200ER pll picking algorithm
  drm/edid: Fix potential memory leak in edid_load()
  drm/udl: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1]
  drm/radeon/kms: allow "invalid" DB formats as a means to disable DB
  ...

Commit 72121572 ("GPIO: gpio-pxa: fix devicetree functions") added an
"xlate" function pointer to the irq_domain_ops, but this function is nor
declared or defined anywhere when CONFIG_OF is disabled, causing the
build error:

  drivers/gpio/gpio-pxa.c:532:11: error: 'irq_domain_xlate_twocell' undeclared here (not in a function)

Extending the DT-only code section to cover the irq_domain_ops and the
pxa_gpio_dt_ids solves this problem and makes it clearer which code is
actually used without DT.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fix is a backport from the reworked nouveau driver.  It masks off the
engines we're not expecting to use before attempting a channel kickoff.
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

The copy engine exhibits random memory corruption in at least one case, the
GeForce 320M (nv50, 0xaf) in the MacBookAir3,1.

This patch omits creating the engine for the specific chipset, falling back
to M2MF, which kills the symptoms.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Fixes screen being black after changing performance level.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: stable@vger.kernel.org [3.5+]
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

At least partially fixes DP output detection on W530.  Not sure if more
issues remain, or if my adaptor is just behaving weirdly (it does that
sometimes).

In any case, this patch is necessary.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>