Enable led sub device in Marvell 88PM860x. Two LED arrays can be supported.
Each LED array can be used for R,G,B leds.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This driver provides an interface for controlling LEDs (or vibrators)
connected to PMICs for which there is a regulator framework driver.

This driver can be used, for instance, to control vibrator on all Motorola EZX
phones using the pcap-regulator driver services.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The LT3593 is a step-up DC/DC converter designed to drive up to ten
white LEDs in series. The current flow can be set with a control pin.

This driver controls any number of such devices connected on generic
GPIOs and exports the function as as platform_driver.

The gpio_led platform data struct definition is reused for this purpose.

Successfully tested on a PXA embedded board.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

This code is based on a driver that came in the "Open-source
and GPL components" download here:

http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Server+Products&ProductLine=Intel%C2%AE+Storage+Systems&ProductProduct=Intel%C2%AE+Entry+Storage+System+SS4200-E&OSVersion=OS+Independent

It was in a file called nasgpio.c inside of a second zip file
called SS4200-E_Linux_SIO_Driver-v1.4.zip and is based on this
updated to use the LED subsystem with the ioctl and hardware
monitor support removed.

I don't have any need for brightness
control, and its code is *completely* separate from the on/off
controls implemented here.  If anyone else wants it, I'd be
happy to look into adding it, but I don't care enough for now.

Except for the probe routines, I rewrote most of it.  I also
Note that I don't have any hardware documentation except for
the original driver.

Thanks go to Arjan for his help in getting the original source
for this released and for chasing down some licensing issues.
Signed-off-by: NDave Hansen <dave@sr71.net>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The WM831x devices feature two software controlled status LEDs with
hardware assisted blinking.

The device can also autonomously control the LEDs based on a selection
of sources.  This can be configured at boot time using either platform
data or the chip OTP.  A sysfs file in the style of that for triggers
allowing the control source to be configured at run time.  Triggers
can't be used here since they can't depend on the implementation details
of a specific LED type.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

LEDs driver for National Semiconductor LP3944 Funlight Chip
http://www.national.com/pf/LP/LP3944.html

This helper chip can drive up to 8 leds, with two programmable DIM
modes; it could even be used as a gpio expander but this driver assumes
it is used as a led controller.

The DIM modes are used to set _blink_ patterns for leds, the pattern is
specified supplying two parameters:
  - period: from 0s to 1.6s
  - duty cycle: percentage of the period the led is on, from 0 to 100

LP3944 can be found on Motorola A910 smartphone, where it drives the rgb
leds, the camera flash light and the displays backlights.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

ROHM BD2802GU is a RGB LED controller attached to i2c bus and specifically
engineered for decoration purposes.  This RGB controller incorporates
lighting patterns and illuminates.

This driver is designed to minimize power consumption, so when there is no
emitting LED, it enters to reset state.  And because the BD2802GU has lots
of features that can't be covered by the current LED framework, it
provides Advanced Configuration Function(ADF) mode, so that user
applications can set registers of BD2802GU directly.

Here are basic usage examples :
; to turn on LED (not blink)
$ echo 1 > /sys/class/leds/led1_R/brightness
; to blink LED
$ echo timer > /sys/class/leds/led1_R/trigger
$ echo 1 > /sys/class/leds/led1_R/delay_on
$ echo 1 > /sys/class/leds/led1_R/delay_off
; to turn off LED
$ echo 0 > /sys/class/leds/led1_R/brightness

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NKim Kyuwon <chammoru@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The gpio led trigger will allow leds to be triggered by
gpio events.

When we give the led a gpio number, the trigger will
request_irq() on that so we don't have to keep polling
for gpio state.

It's useful for usecases as n810's keypad leds that could
be triggered by the gpio event generated when user slides
up to show the keypad.

We also provide means for userland to tell us what is the
desired brightness for that special led when it goes on
so userland could use information from ambient light sensors
and not set led brightness too high if it's not necessary.
Signed-off-by: NFelipe Balbi <me@felipebalbi.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Mikrotik built six LEDs into the Routerboard 532, from which one is
destined for custom use, the so called "User LED". This patch adds a
driver for it, based on the LEDs class.
Signed-off-by: NPhil Sutter <n0-1@freewrt.org>
Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Add a simple driver for pwm driver LEDs.  pwm_id and period can be defined
in board file.  It is developed for pxa, however it is probably generic
enough to be used on other platforms with pwm.
Signed-off-by: NLuotao Fu <l.fu@pengutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Add an LED driver using the DAC124S085 DAC from NatSemi

[randy.dunlap@oracle.com: use header files for interfaces]
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Move the second part of the HP laptop disk protection functionality (a red
led) to the same driver.  From a purely Linux developer's point of view,
the led and the accelerometer have nothing related.  However, they
correspond to the same ACPI functionality, and so will always be used
together, moreover as they share the same ACPI PNP alias, there is no
other simple to allow to have same loaded at the same time if they are not
in the same module.  Also make it requires the led class to compile and
update the Kconfig text.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The voltage and current regulators on the WM8350 AudioPlus PMIC can be
used in concert to provide a power efficient LED driver.  This driver
implements support for this within the standard LED class.

Platform initialisation code should configure the LED hardware in the
init callback provided by the WM8350 core driver.  The callback should
use wm8350_isink_set_flash(), wm8350_dcdc25_set_mode() and
wm8350_dcdc_set_slot() to configure the operating parameters of the
regulators for their hardware and then then use wm8350_register_led() to
instantiate the LED driver.

This driver was originally written by Liam Girdwood, though it has been
extensively modified since then.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Driver for PC Engines ALIX.2 and ALIX.3 LEDs.
Signed-off-by: NConstantin Baranov <const@mimas.ru>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

HP notebooks contain accelerometer-based disk protection subsystem,
and LED that indicates hard disk is protected. This is driver for the
LED part.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The cm-x270 board uses leds-gpio so remove the now unneeded driver.
Acked-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

This allows LEDs to be controlled as a backlight device where
they turn off and on when the display is blanked and unblanked.
This is useful where you need various key backlight LEDs to
dim at the same time as the backlight.
Signed-off-by: NRodolfo Giometti <giometti@linux.it>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-spitz

Drop leds-spitz.c and the declarations of now un-referenced
spitzscoop_device, spitzscoop2_device.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-corgi

Drop leds-corgi.c and remove the declaration of now un-referenced
corgiscoop_device.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver supports the PCA9550, PCA9551, PCA9552, and PCA9553
LED driver chips.
Signed-off-by: NNate Case <ncase@xes-inc.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

NXP pca9532 is a LED dimmer/controller attached to i2c bus.  It allows
attaching upto 16 leds which can either be on, off or dimmed and/or blinked
with the two PWM modulators available.

This driver is a "new-style" i2c driver that adheres to the driver model and
implements the led framework api.  Since the leds connected to the driver are
platform specific, it is only useful when platform data is passed to the
driver to define what leds are connected to which pins.
Signed-off-by: NRiku Voipio <riku.voipio@iki.fi>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

Add a trigger which allows LEDs to default to the full
brightness state.
Signed-off-by: NNick Forbes <Nick.Forbes@huntsworth.com>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

The LEDs on the Freecom FSG-3 are connected to an external
memory-mapped latch on the ixp4xx expansion bus, and therefore cannot
be supported by any of the existing LEDs drivers.
Signed-off-by: NRod Whitby <rod@whitby.id.au>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

As now tosa uses leds-gpio, drop leds-tosa driver.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is a LED driver using the PWM on newer SOCs from Atmel; brightness is
controlled by changing the PWM duty cycle.  So for example if you've set up
two leds labeled "pwm0" and "pwm1":

	echo 0 > /sys/class/leds/pwm2/brightness	# off (0%)
	echo 80 > /sys/class/leds/pwm2/brightness
	echo 255 > /sys/class/leds/pwm2/brightness	# on (100%)

Note that "brightness" here isn't linear; maybe that should change.  Going
from 4 to 8 probably doubles perceived brightness, while 244 to 248 is
imperceptible.

This is mostly intended to be a simple example of PWM, although it's
realistic since LCD backlights are often driven with PWM to conserve
battery power (and offer brightness options).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the LEDs on the HP Jornada 620/660/680/690 devices.
Signed-off-by: NKristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

All boards using the IXP4XX-GPIO-LED driver have been updated to use
the generic leds-gpio driver instead.
Signed-off-by: NRod Whitby <rod@whitby.id.au>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

The driver supports the mail LED commonly found on different Clevo notebooks.
The driver access the LED through the i8042 hardware which is handled by
the input subsystem.
Signed-off-by: NMárton Németh <nm127@freemail.hu>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

This patch provides core support for CM-X270 platform.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add Cobalt Raq series LEDs support.
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

The leds-cobalt driver only supports the Coable Qube series
(not included in Cobalt Raq series).
Rename the driver and update Kconfig/Makefile.
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: NFlorian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

This patch adds support for GPIO connected leds via the new GPIO framework.

Information about leds (gpio, polarity, name, default trigger) is passed
to the driver via platform_data.
Signed-off-by: NRaphael Assenat <raph@8d.com>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

Add support for Cobalt Server front LED (MIPS)
Signed-off-by: NFlorian Fainell <florian.fainelli@int-evry.fr>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

This patch adds the support for the IPAQ h1940 leds.

In order to create the amber led (used for the battery charging), the red and
green leds are set to the same default trigger. Due to hardware limitations,
the blue led can only be set in blinking mode.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

A driver for the PCEngines WRAP boards (http://www.pcengines.ch), which are
very similar to the Soekris net4801 (same NS SC1100 geode reference
design).

The LEDs on the WRAP are on different GPIO lines and I have modified and
copied the net48xx error led support for this.  It also includes support
for an "extra" led (in addition to error).  The three LEDs on the WRAP are
at GPIO lines 2,3,18 (WRAP LEDs from left to right).  This driver gives
access to the second and third LEDs by twiddling GPIO lines 3 & 18.

Because these boards are so similar to the net48xx, I basically sed-ed that
driver to form the basis for leds-wrap.c.  The only changes from
leds-net48xx.c are:

 - #define WRAP_EXTRA_LED_GPIO

 - name changes

 - duplicate relevant sections to provide support for the "extra" led

 - reverse the various *_led_set values.  The WRAP is "backwards" from the
   net48xx, and these needed to be updated for that.

[akpm@osdl.org: build fix]
Signed-off-by: NKristian Kielhofner <kris@krisk.org>
Acked-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add LED Class device support for the Soekris net48xx Error LED.  Tested
only on a net4801, but should work on a net4826 as well.  I'd love to find
a way of detecting a Soekris net48xx device but there is no DMI or any
Soekris-specific PCI devices.

[akpm@osdl.org: fixlets, cleanups]
Signed-off-by: NChris Boot <bootc@bootc.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add an LED trigger acts like a heart beat.  This can be used as a
replacement of CONFIG_HEARTBEAT code exists in some arch's timer code.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: NRichard Purdie <rpurdie@rpsys.net>
Cc: "Nish Aravamudan" <nish.aravamudan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>