On EP93XX uncompress.h uses CONFIG_DEBUG_UART_PHYS instead of a hard
coded serial port. This means the build breaks when DEBUG_LL
(and DEBUG_LL_UART_PL01X) is not enabled.

This is fixed by adding a new dependency.
Signed-off-by: NDaniel Thompson <daniel.thompson@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As part of the migration we introduce DEBUG_UART_PHYS/DEBUG_UART_VIRT
which default to UART1 but allow a user to configure UART2 or UART3.
We also introduce symbolic names for the registers and flags.
Signed-off-by: NDaniel Thompson <daniel.thompson@linaro.org>
Acked-by: NArnd Bergmann <arnd.bergmann@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The omap1's debug-macro.S is similar to the generic 8250 code. Compared to
the 8520 code the omap1 macro automatically determines what UART to use
based on breadcrumbs left by the bootloader and automatically copes with
the eccentric register layout on OMAP7XX.

This patch drops both these features and relies instead on the generic
8250 macros:

1. Dropping support for the bootloader breadcrumbs is identical to the
   way the migration was handled for OMAP2 (see 808b7e07...).

2. Support for OMAP7XX still exists but it must be configured by hand
   (DEBUG_OMAP7XXUART1/2/3) rather than handled at runtime.
Signed-off-by: NDaniel Thompson <daniel.thompson@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: linux-omap@vger.kernel.org
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As part of the migration a couple of uart definitions have been copied
from of the platform specific header files.
Signed-off-by: NDaniel Thompson <daniel.thompson@linaro.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Only a very small handful of platforms support DEBUG_LL_UART_NONE but it
lurks in the menus of every single platform config ready to break the
build. This is an especial problem for defconfig/oldconfig since it is
often selected by default.

This patch solves the problem by removing this option. Any platforms
still depending upon this option must be migrated.
Signed-off-by: NDaniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The default value for DEBUG_CNS3xxx appears twice. This patch removes
the one with the wrong sort order.
Signed-off-by: NDaniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Since there is no public documentation, this patch also provide register
offsets for different UART units on this SoC.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This device actually has a 8250 serial with a shift of 0.
Tested this on a BCM4708.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

StrongARM debug-macro.S is quite standalone thing, depending only on
register mappings. Move it to proper place and add Kconfig entry.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Add serial port debug macros for the SCIF(A) serial ports.
This includes all supported shmobile SoCs, except for EMEV2.

The configuration logic (both Kconfig and #ifdef) is more complicated than
one would expect, for several reasons:
  1. Not all SoCs have the same serial devices, and they're not always
     at the same addresses.
  2. There are two different types: SCIF and SCIFA. Fortunately they can
     easily be distinguished by physical address.
  3. Not all boards use the same serial port for the console.
     The defaults correspond to the boards that are supported in
     mainline. If you want to use a different serial port, just change
     the value of CONFIG_DEBUG_UART_PHYS, and the rest will auto-adapt.
  4. debug_ll_io_init() maps the SCIF(A) registers to a fixed virtual
     address. 0xfdxxxxxx was chosen, as it should lie below VMALLOC_END
     = 0xff000000, and must not conflict with the 2 MiB reserved region
     at PCI_IO_VIRT_BASE = 0xfee00000.
       - On SoCs not using the legacy machine_desc.map_io(),
	 debug_ll_io_init() is called by the ARM core code.
       - On SoCs using the legacy machine_desc.map_io(),
	 debug_ll_io_init() must be called explicitly. Calls are added
	 for r8a7740, r8a7779, sh7372, and sh73a0.

This was derived from the r8a7790 version by Laurent Pinchart.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable low-level debug for Mediatek mt8127 & mt8135 SoC.
Signed-off-by: NJoe.C <yingjoe.chen@mediatek.com>
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>

Removing minimal support for etb/etm to favour an implementation
that is more flexible, extensible and capable of handling more
platforms.

Also removing the only client of the old driver.  That code can
easily be replaced by entries for etb/etm in the device tree.
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver manages CoreSight ETM (Embedded Trace Macrocell) that
supports processor tracing. Currently supported version are ARM
ETMv3.x and PTM1.x.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>

coresight-etm3x: adding missing error checking
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver manages CoreSight ETB (Embedded Trace Buffer) which
acts as a circular buffer sink collecting generated trace data.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver manages CoreSight TPIU (Trace Port Interface Unit)
which acts as a sink. TPIU is typically connected to some offchip
hardware hosting a storage buffer.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver manages CoreSight TMC (Trace Memory Controller) which
can act as a link or a sink depending upon its configuration. It
can present itself as an ETF (Embedded Trace FIFO) or ETR
(Embedded Trace Router).

ETF when configured in circular buffer mode acts as a trace
collection sink. When configured in HW fifo mode it acts as link.
ETR always acts as a sink and can be used to route data to memory
allocated in RAM.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CoreSight components are compliant with the ARM CoreSight
architecture specification and can be connected in various
topologies to suit a particular SoC tracing needs. These trace
components can generally be classified as sources, links and
sinks. Trace data produced by one or more sources flows through
the intermediate links connecting the source to the currently
selected sink.

The CoreSight framework provides an interface for the CoreSight trace
drivers to register themselves with. It's intended to build up a
topological view of the CoreSight components and configure the
correct serie of components on user input via sysfs.

For eg., when enabling a source, the framework builds up a path
consisting of all the components connecting the source to the
currently selected sink(s) and enables all of them.

The framework also supports switching between available sinks
and provides status information to user space applications
through the debugfs interface.
Signed-off-by: NPratik Patel <pratikp@codeaurora.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the UART definitions needed to support earlyprintk on brcmstb machines.
Signed-off-by: NMarc Carino <marc.ceeeee@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

The commit 2111667b ("ARM: pxa: call debug_ll_io_init for
earlyprintk") triggers in the current kernel the attached backtrace on
PXA/tosa early in the boot time when DEBUG_LL is enabled.

It is due to overlap between uart virtual memory defined in
DEBUG_UART_VIRT and mapped by debug_ll_io_init() and peripheral bus
mapped by pxa_map_io at the same address, 0xf2100000.

As hinted by Arnd, map early virtual memory for low level debug on
address 0xf6200000, even if that means 2 virtual mappings will give
access to the pxa internal UARTs (FFUART, BTUART, STUART, ...).

------------[ cut here ]------------
kernel BUG at /home/lumag/linux/mm/vmalloc.c:1143!
Internal error: Oops - BUG: 0 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.17.0-00032-g8e0d202-dirty #23
task: c062a5a8 ti: c0620000 task.ti: c0620000
PC is at vm_area_add_early+0x54/0x84
LR is at add_static_vm_early+0xc/0x60
pc : [<c03e1100>]    lr : [<c03d9ef4>]    psr: 800001d3
sp : c0621f04  ip : c03efa74  fp : c03edf84
r10: c0637e98  r9 : 40000001  r8 : c03da57c
r7 : c3ffcfb0  r6 : 00000000  r5 : c3ffcfb0  r4 : 02000000
r3 : c3ffcfd8  r2 : f2100000  r1 : f4000000  r0 : c3ffcfb0
Flags: Nzcv  IRQs off  FIQs off  Mode SVC_32  ISA ARM  Segment kernel
Control: 00007977  Table: a0004000  DAC: 00000017
Process swapper (pid: 0, stack limit = 0xc06201c8)
Stack: (0xc0621f04 to 0xc0622000)
1f00:          c3ffcfd8 40000001 c3ffcfd8 c03ee08c c03da570 c03db90c c0637d24
1f20: 00000000 c03ec7cc c066e654 a0700000 000a0700 c03db914 c03db90c c03daf84
1f40: 00000000 000a0000 c0000000 c03ec7cc 000a0700 c0700000 ffff1000 000a3fff
1f60: 00001000 00000007 00000000 c03ec7cc c0008000 c03ed748 c0621fd4 c03d5d18
1f80: 69052d00 a03ec48c 00000000 c03d8ad0 0000006c 00007977 c036c6e8 00000001
1fa0: c0621fd4 c03ed744 c0628000 a0004000 69052d00 a03ec48c 00000000 c03d68d4
1fc0: 00000000 00000000 00000000 00000000 00000000 c03ed748 c0649894 c062801c
1fe0: c03ed744 c062b2f0 a0004000 69052d00 a03ec48c a0008040 00000000 00000000
[<c03e1100>] (vm_area_add_early) from [<c03d9ef4>] (add_static_vm_early+0xc/0x60)
[<c03d9ef4>] (add_static_vm_early) from [<c03da570>] (iotable_init.part.6+0xa8/0xb4)
[<c03da570>] (iotable_init.part.6) from [<c03db914>] (pxa25x_map_io+0x8/0x24)
[<c03db914>] (pxa25x_map_io) from [<c03daf84>] (paging_init+0x744/0x8d8)
[<c03daf84>] (paging_init) from [<c03d8ad0>] (setup_arch+0x354/0x608)
[<c03d8ad0>] (setup_arch) from [<c03d68d4>] (start_kernel+0xa8/0x3dc)
[<c03d68d4>] (start_kernel) from [<a0008040>] (0xa0008040)
Code: e5904008 e0811004 e1520001 2a000005 (e7f001f2)
---[ end trace f24b6c88ae00fa9a ]---
Kernel panic - not syncing: Attempted to kill the idle task!
---[ end Kernel panic - not syncing: Attempted to kill the idle task!

Cc: <stable@vger.kernel.org>
Reported-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NArnd Bergmann <arnd@arndb.de>

The uarts on sun9i are still compatible with the dw_8250, but are
located at different addresses.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

UARTs on CNS3xxx are 8250-compatible, not AMBA.
The base address for UART0 is 0x78000000 (physical)
and 0xfb002000 (virtual).
Signed-off-by: NKrzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

UARTs on CNS3xxx are 8250-compatible, not AMBA.
The base address for UART0 is 0x78000000 (physical)
and 0xfb002000 (virtual).
Signed-off-by: NKrzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Add the UART definitions needed to support earlyprintk for MesonX SoCs
on UARTAO.
Signed-off-by: NCarlo Caione <carlo@caione.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Enable low-level debug for Mediatek mt6589 SoC on UART0.
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

HIP04 was added out of order, but so was the previous HISI debug uart
support as well. Minor reshuffling of order.
Signed-off-by: NOlof Johansson <olof@lixom.net>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Broadcom BCM63xx DSL SoCs have a different UART implementation for which
we need specially crafted low-level debug assembly code to support. Add
support for this using the standard definitions provided in
include/linux/serial_bcm63xx.h (shared with their MIPS counterparts).
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add the support of Hisilicon HiP04 debug uart.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

Rename Hisilicon HI3716 to HIX5HD2 and add dependency on ARCH_HIX5HD2.

HiX5HD2 is a SoC with dual Cortex A9 cores for STB market, and original
Hi3xxx SoC is for mobile market.

To avoid confusing the two types of SoCs and also because of different
implementation (SMP, IPs integrated and earlycon config), rename Hi3716
to HIX5HD2 and add ARCH_HIX5HD2.
Signed-off-by: NHaifeng Yan <yanhaifeng@gmail.com>
Signed-off-by: NJiancheng Xue <jchxue@gmail.com>
Signed-off-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: NWei Xu <xuwei5@hisilicon.com>
[olof: fixed description typos]
Signed-off-by: NOlof Johansson <olof@lixom.net>

The uarts on rk3288 are still compatible with the dw_8250, but located
at a different position and need DEBUG_UART_8250_WORD enabled.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NWill Deacon <will.deacon@arm.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

The debug uart settings from the DEBUG_RK3X_UART options are usable on
all Rockchip SoCs from the rk30xx and rk31xx series but not on the
new rk3288 SoCs. Thus clarify their use to prevent confusion.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Move debug-macro.S from mach/include to include/debug where
all other common debug macros are.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

In a multiplatform config, the low level debug option shows several
UART port entries. Improve the user visible string so that it becomes
clear to the user about Samsung UART ports.
While at it also remove some lines from the help text that are no
longer applicable across all Samsung platforms.
Signed-off-by: NSachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Now that all boards have been converted to DT and all the support code
lives in mach-mvebu, we can remove mach-kirkwood.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1405028192-9623-2-git-send-email-andrew@lunn.chSigned-off-by: NJason Cooper <jason@lakedaemon.net>

One more step to allowing CLPS711X to participate in the
multi-platform defconfig.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NOlof Johansson <olof@lixom.net>

sun6i/sun8i have a UART in the RTC block group, which can be used
as an early console. This is most useful on sun8i as UART0 is muxed
with MMC0, which is not available if we boot from MMC.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add information about the APQ8084 debug UART physical and virtual
addresses in the DEBUG_QCOM_UARTDM Kconfig help section.
Signed-off-by: NGeorgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Move debug-macro.S from mach/include to include/debug where
all other common debug macros are.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This removes the need for mach/-headers in the debug macro.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Using the lowlevel debug uart is a corner case - even more so in a
multiplatform environment. So it seems reasonable to simply let the
developer set the appropriate uart type for the debugged SoC.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>