After exynos_dp have been split the common IP code into analogix_dp driver,
the analogix_dp driver have deprecated some Samsung platform properties which
could be dynamically parsed from EDID/MODE/DPCD message, so this is an update
for Exynos DTS file for dp-controller.

Beside the backward compatibility is fully preserved, so there are no
bisectability break that make this change in a separate patch.
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NYakir Yang <ykk@rock-chips.com>

Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux-keypad,wakeup" boolean property to enable the
wakeup source, "wakeup-source" is the new standard binding.

This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>

The eMMC is non-removable so mark it using the non-removable DT
property to avoid having to redetect it after a suspend/resume.

Also remove the card-detect-delay property that is not needed with
non-removable.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>

The Exynos5250 Snow Chromebooks have a Marvell WiFi SDIO chip which
can't neither be removed nor be detected. But the node isn't marked
as non-removable and instead has the broken-cd DT property.

This causes the device to be removed when the system enters into a
suspend state and the following warnings is shown after a resume:

[  181.944636] mmc2: error -2 during resume (card was removed?)

Also remove the card-detect-delay property that is not needed with
non-removable.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>

There are 2 revisions of the Exynos5250 Snow Chromebook that were
shipped: Rev4 and Rev5. The only difference between these 2 revisions
is the codec, Rev4 has a max98095 codec while Rev5 has a max98090.

Mainline only supports Rev4 so this patch moves the common device
nodes to a DTSI file and adds a DTS for the Exynos5250 Snow Rev5.

The Snow Rev5 DTS is based on the DTS found in the ChromiumOS 3.8
tree.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Tested-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>
Reviewed-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Although there is only one choice of chipselect it is necessary to
specify it. The driver cannot claim the gpio otherwise.
Signed-off-by: NMichal Suchanek <hramrach@gmail.com>
Acked-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Acked-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

For Exynos5250 platforms, add CPU operating points and CPU regulator
supply properties for migrating from Exynos specific cpufreq driver
to using generic cpufreq driver.

Cc: Doug Anderson <dianders@chromium.org>
Cc: Andreas Faerber <afaerber@suse.de>
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
[b.zolnierkie: split Exynos5250 support from the original patch]
[b.zolnierkie: added CPU regulator supply property for Spring boards]
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier@dowhile0.org>
Tested-by: NJavier Martinez Canillas <javier@dowhile0.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

The i2c_7 node (i2c@12CD0000) with LVDS bridge child node was put in
Exynos5250 Snow DTS file twice. Move the LVDS bridge to proper existing
i2c_7 node.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

The Marvell mwifiex driver prevents the system to enter into a suspend
state if the card power is not preserved during a suspend/resume cycle.

So Suspend-to-RAM and Suspend-to-idle are failing on Exynos5250 Snow.

Add the keep-power-in-suspend Power Management property to the SDIO/MMC
node so the mwifiex suspend handler doesn't fail and the system is able
to enter into a suspend state.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

The kernel can use as the default console a serial port if is defined
as stdout device in the Device Tree.

This allows a board to be booted without the need of having a console
parameter in the kernel command line.

Currently the Snow DTS has a bootargs in the /chosen node and this is
kept since users that don't have a serial console on this board might
be using it to have the boot log shown in the display. This will have
more precedence than the stdout-path but it's fine since is only used
when CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND is enabled.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Define videoports and use endpoints to describe the connection between
the encoder, bridge and the panel, instead of using phandles.
Signed-off-by: NAjay Kumar <ajaykumar.rs@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Tested-by: NRahul Sharma <rahul.sharma@samsung.com>
Tested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Enabling SDIO IRQ signalling for the wifi MMC/SDIO slot
doubles the transmission transfer rate.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

The Snow board has a MMC/SDIO wifi chip that is always powered but it
needs a power sequence involving a reset (active low) and an enable
(active high) pins. Both pins are marked as active low since the MMC
simple power sequence driver asserts the pins prior to the card power
up procedure and de-asserts the pins after the card has been powered.

So the reset line will be left de-asserted and the enable pin will be
left asserted.

The chip also needs an external 32kHz reference clock to be operational
that is by the MAX77686 PMIC clock.

Add a simple MMC power sequence provider for the wifi MMC/SDIO slot.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

The Exynos5250 Snow Chromebook has GPIO keys for power and lid
so the SoC I/O pins have to be configured in external interrupt
mode. Currently, this is working without setting the pinctrl
lines but is better to set it explicitly instead of relying on
the previous state of the I/O pins.

The DTS snippets were taken from the downstream ChromeOS tree.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Explicitly set the dr_mode for the dwc3 controller on the
Snow board to host mode. This is required to ensure the
controller is initialized in the right mode if the kernel is
build with USB gadget support.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

commit 546b117fdf17 ("rtc: s3c: add support for RTC of Exynos3250 SoC")
added an "rtc_src" DT property for the Samsung's S3C Real Time Clock
controller that specifies the 32.768 kHz clock that uses the RTC as
its source clock. In the case of the Exynos5250 based Snow board, the
Maxim 77686 32kHz AP clock is used as the source clock.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Use the new style for referencing inherited nodes and use symbolic
names. Goal is the alignment of all exynos5250 based device trees
for comparison.
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: rebased and squashed]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

exynos5250-cros-common.dtsi had an empty /chosen node.
Fill in exemplary boot arguments.
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Use the new style of referencing inherited nodes and use symbolic
names. Reorder one pinctrl node in GPIO order.
Goal is the alignment of all exynos5250 based device trees for
comparison.
Suggested-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: rebased and squashed]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add DT nodes for ptn3460 bridge chip and panel.
Add backlight enable pin and backlight power supply for pwm-backlight.
Also add bridge phandle needed by dp to enable display on snow.
Signed-off-by: NAjay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

dw-mmc controller can support multiple slots.
But, there are no use-cases anywhere. So we don't need to support the
slot-node for dw-mmc controller.
And "supports-highspeed" property in dw-mmc is deprecated.
"supports-highspeed" property can be replaced with "cap-sd/mmc-highspeed".
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NTushar Behera <trblinux@gmail.com>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NSachin Kamat <sachin.kamat@samsung.com>
[kgene.kim@samsung.com: rebased exynos5250-snow changes]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

exynos5250-cros-common.dtsi was meant for sharing common pieces across
ChromeOS devices. This turned out premature, as several devices ended up
in the common file that are not common after all. Since the remaining
common ChromeOS pieces are fairly minor,  exynos5250-cros-common.dtsi
was requested to be merged into the Snow device tree, sharing only the
keyboard controller for now. This may be re-evaluated as both mature.
Suggested-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The pinctrl properties should be on the device directly and not on the
slot sub-node.
Reported-by: NDoug Anderson <dianders@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Move it from exynos5250-cros-common.dtsi to exynos5250-snow.dts.
Spring does not need it, it uses an Atmel maXTouch instead.
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Move it from exynos5250-cros-common.dtsi to exynos5250-snow.dts.
Spring does not need it, it uses an s5m8767 instead.
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add sound-card name property to Snow/Peach-Pit/Peach-Pi boards.
Signed-off-by: NTushar Behera <tushar.b@samsung.com>
Acked-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Enable dp-controller for snow board.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Enable fimd node for snow board.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add PWM backlight node for exynos5250 based snow board.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NAjay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add required fixed-regulator for VBUS supply for USB 3.0
controller phy.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The audio codec on Snow board, MAX98095 is connected on I2C7 bus.
Also it requires the GPX1-7 line to be pulled up.

Updated Snow DTS file to incorporate above changes and added a
sound node to instantiate the I2S-based sound card.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Enable support for HDMI for exynos5250 based Snow board.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Acked-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Added TPS65090 regulator related nodes to Snow board.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Added pinctrl node for embedded controller (EC) IRQ
on Snow board.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Added i2c-arbitrator pinctrl node to Snow board.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add generic compatible strings to the respective board DT files.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Some boards might not have RTC xtal, so RTC shouldn't really be
enabled by default. Enable it in the required board files. For
now enable it for all board files to maintain the enabled status
exisitng prior to this patch.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Make it easier to notice the common file for ChromeOS devices based on
the Exynos5250 by giving it the exynos5250 prefix that the boards have.
Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NTomasz Figa <t.figa@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Commit e908d5c5 ("ARM: dts: change status property of dwmmc nodes
for exynos5250") missed out handling the exynos5250 snow dts file.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>